A mixture for bas-relief with your own hands. Decorative gypsum bas-relief on the wall: as a newcomer to make it with your own hands

Lrack on the walls interior premises Always considered a sign of a good taste and prosperity. Today, despite the fact that there are a wide variety of various gypsum and plastic finished elements that can be decorated with walls of a room in the house, but the modeling on the wall will deliver a lot of pleasure on the wall and makes proud of your work. Still, because you made it yourself. Someone maybe think that the modeling on the wall is difficult. Not at all. Each person who even never scared before, can easily cope with such work. It would be only a desire to create.

Beautifully decorated modeling will decorate any wall, make it dear and stylish.

How to make a laying on the wall with your own hands

This will require:

• building mixture for plaster;
• sculpture clay (or other material);
• stacks, knife, kneading capacity;
• rock.

Before proceeding with the modeling, you should prepare the wall of the room, it should be carefully leveled with plaster. Clay for the modeling should be mixed so that it does not stick to the hands. Elements of the planned composition will be formed from it. Part of the clay is mixed in the container to the state of the liquid sour cream. It is called a slip and needed to connect the finished elements to each other.

Tools for modeling.

You can sculpt anything, but most often various vegetable compositions are made. From a piece of involved clay, you need to break as much as it is necessary to create one element, and the rest of the clay should be kept wrapped in wet cloth and plastic bag. It will keep it from drying out.

Can be simple example Consider how very simply grape bunch. You need to take a sheet of grapes, put it on a polyethylene film and circle along the contour. It will be a template. Then the clay and shlice is mixed. A piece of clay is rolled up with a rolling pin in a cake and is attached to the surface of the wall with a slicker. The template is placed on the clay and rushes along the contour. Using tools, an extra clay is removed. You can use both professional tools (stacks) and any foolish. First, the contour of the sheet is formed, and then the inner part (streak and deepening).

The sheet should be on the vine. Therefore, a thin harness is rolled out of clay and attached to the wall. Then the balls roll out of clay and a bunch of grapes is formed. After the manufacture, the composition should dry. Then, along with the wall, it is covered with primer and paint with water-mounted paint or running. You can make a color composition, adding a color to paint and using artistic brushes.

Modeling with putty and other materials

Instead of sculptural clay, you can use putty. It is mixed in the tank, applied to the wall and, while the spacure is raw, the elements of the composition are formed. It is recommended to form sequentially small sitesSince this material dries quickly enough. Instead of putty, you can use gypsum or alabaster.

Photo 1. Step-shit embossed painted walls will decorate the children's room.

The described method can be decorated with a wall with relief. But you can make a surround image and decorate, for example, a wall or angle of the children's room. A child from such an ornament will simply be delighted (photo 1).

The easiest way to do all the same vegetable compositions, as in the example above with grapes. Consider how you can cut the bulk branch of the tree with leaves and a bird sitting on it.

In order for the branch to be volumetric, it is necessary to make a frame. It is made from the wire that is screwed to the wall of the room using self-tapping screws. In the wall in the places of fasteners, it is pre-drilled holes and drive the plastic dowels in them. Wire fixed on the wall should be wrapped with a bandage and deceive with a solution of sculptural clay, putty, gypsum or alabastra. Using a knife, you need to form a tree bark on the resulting branch. It remains only to attach the leaves and put a bird on the branch. The bird is easiest to cut out of clay, as it is more plastic.

After drying, the whole composition is painted. You can use gouache or water-emulsion paint by adding a kel into it. It looks like this decoration is simply great, especially if you make a backlight with a small point lamp with directional beam of light.

Decoration living room stucco composition

The wall in the living room can also be decorated with a large vegetable composition flipped from putty. You need to choose an open surface that is not closed with interior elements and furniture. As already mentioned, the wall should be completely smooth. It is easier to work with vegetable elements, since symmetry is not required. A composition with large parts is more suitable for the living room, for example, big flower or tree.

Photo 2. You can decorate the living room with a stucco composition with a putty.

First, the contour is drawn on the wall surface. You can then dilute the putty and put it with a spatula on the wall, right there by forming the desired part of the part with a knife and other girlish tools. If the putty is dry, then you can trust the work, carefully cutting up too much. But it is still easier to work with raw material.

It is possible to work with a putty and in another way, overlapping it with layers by forming a volume. Each layer must dry. The lower layers are not necessary to smooth out, so they will be better to hold on to those that are superimposed on top. Some craftsmen recommend to knead the putty, adding toilet paper to it to give a solution of the best plasticity.

Such a flower or tree on the wall of the hall will not only decorate the room, but will serve as a subject of your pride, because All this you did with your own hands.

So, decorate the walls with a modeling is not difficult and does not require professional skills, especially if used useful recommendations. Need to use your fantasy to create really original composition (Photo 2).

It should be noted that the stucco composition looks many times more attractive if it is highlighted.

Therefore, choosing a wall for work, you immediately need to determine where the lamps can be installed.

His house wants to make beautiful and original. Most reliable way - Unique homemade decorations. One of the very interesting ways - Bas-relief on the wall. This is a three-dimensional image of a plaster or any other similar material. Gypsum in pure form is used very rarely - it freezes too quickly without giving time to processing. Most often use gypsum plaster mixes. They go with additives that facilitate work. With them, you can make a bulk wall panel with your own hands even without experience.

Total Bas Account Creation Technology

To make a bas-relief on the wall, it is necessary to prepare it to start it: clean, align. Already on a flat and completely dry surface, you can start working. When you are going to make large bas-reliefs, it is advisable to climb the wall - for a better clutch of the composition with the wall.

Bas-relief on the wall can be of varying degrees of complexity. This is complicated. For beginners is clearly unasamed. But you know what can be done in perspective

For first experience, it is better to start with small products - type of medallions (round or square) with simple embossed images. As the basis for such products, it is best to take moisture-resistant. Under it can make a frame (from the profile, for example). In this form, the bulk composition can be outweigh from place to place. It is easier to master the basics of technology.

This is all the technology in general features. There are nuances on which it is worth stopping separately. The first concerns applying the starting layer of putty on the walls and transfer of the pattern. In more complex compositions, the bas-relief on the wall begins with the transfer of contours of the drawing. Do it with a pencil or chalk (if you know how to draw) or using the image printed in the desired size and the copier-plated software. Then those places on which we will apply putty are covered with soil (for better clutch), and then with the help of Mastekhins (small spatulas different shapes) Apply the first layer of material. Next, the sequence of actions is similar to the described.

Materials for creating bas-relief

The most common question among beginners: What putty is better to take for the manufacture of bas-relief? In principle, come on any finish gypsum putty. Each wizard has its favorite brands and compositions. Here are a few that can be recommended:

• Knauf Uniflot. Very durable and plastic. From it you can form a deep relief - not fall off and without reinforcement. Failure: dear.
• Fugeen. Slightly less durable, it cuts a little worse. Much cheaper than Knauf Uniflot (almost three times). You can also make a relief without any problems.
• Pufas. This is a gypsum putty with cellulose fiber. Processing time - about 60 minutes, it is applied to a layer of any thickness, it is well cut, it is easily grinding.
• "Rotband" for the lower layers and the "tilt" for the upper.
• "Acryl Putz" (Poland). Finished acrylic putty. It is good because he is slowly "grasped", to study the parts of the hour and more (depends on the humidity in the room).

In addition, impregnation is needed. They are selected based on the starting characteristics of the material. There are compounds that strengthen the hearty materials, penetrating deep and binding particles of materials with each other. This is necessary, since the panel of gypsum weigh decently, create an additional load. Without prior preparation, they can fall off from fragile grounds. You can use the moisture-proof soil concentrate firm PUFAS. It is suitable for all mineral bases, including wood and wood slabs. Aquastop moisture protection is suitable for bulk grounds.

In addition, these compositions are used:

• before starting work - to improve the clutch with the wall material (or base);
• for layer-by-layer processing - when creating a deep relief, when one layer of putty is applied to the already dried, imposed earlier;
• for finishing impregnation before painting - for leveling absorbing ability and that the paint lay down exactly, emphasizing the relief, and without being upgraded.

For layer-by-layer processing, primers are needed, which create an adhesive surface on the surface. In this case, you can put a new layer of putty even on the surface of the surface. For these purposes suited primer Ceresit deep penetration and impregnating PUFAS soil. They can be used for finish treatment Before painting.

Instruments

The tools for creating a bas-relief are needed for two types of work - for applying putty and to remove / cut off the extension solution. Therefore, the set of tools and fixtures is quite extensive. For applying putty or decorative paints Use:

These are all tools that may be needed. From the necessary: \u200b\u200bKelma, spatula, chisels. Mastichens are very comfortable, it is difficult without scalpels and a confectionery syringe. But stacks are a tool for perfectionists - for accurate improvement of the relief.

Making a bas-relief from plaster plaster: photo report

For the embossed picture on the wall, a maritime theme was chosen - with fish, octopus, algae. Great option for obtaining first experience! A light pattern that can be formulated gradually.

Preparatory work

The drawing with a pencil is transferred to a pre-aligned and projected surface. For the manufacture of a bas-relief, a gypsum stucco stitching / Sheetrock (with a smaller stamp) is used. During the dilution of the solution, a smaller amount of water is added: to take 0.5 liters of water to a kilogram of the mixture (instead of 0.6 on the recommendation). With such a kneel, the composition is harsh, but it is so better for making a relief image on the wall.

Immediately knead a small amount of solution: the gypsum plaster quickly loses elasticity (15-17 minutes) and you need to have all the volume not only to lay out on the wall, but also align and give the desired outlines. For the first time, knead grams of 300-400, lay out, attach some form. If in the process you will feel that you can cope with a large volume, knead more.

Little way, masticine is laid out the solution, filling the contour of algae, cut off excess, as far as possible

With such tactics - small portions of the solution - most of Time takes exactly to knead the putty. Knead better in the dishes with high side - bucket or saucepan. However, of them, the frozen solution is hard to delete. If there is an old ball in the house, you can cut up the top and knead the putty in it. Even small particles are easily removed from such a container.

Put powder into the container, add clean cold water, quickly mix with a spatula, then bring the composition until uniformity, leave for 5 minutes, then mix again. There must be a homogeneous thick paste without lumps or inhomogeneities. Exposure time and "setting" is indicated on packing with putty, if you use another composition, follow the manufacturer's recommendations.

Formation of small details

To begin with, it is easier to start with a shallow relief. When forming small details We take a small amount of solution on the Kelma, we apply to the right place, trying to swing well to the clutch of the solution with the wall is good. If the wall is covered with a primer that improves the clutch (the surface is slightly rough and lipgy to the touch), there will be no problems. If the details are very small - such as the suckling of jellyfish - it is more convenient to put a masticine solution.

The bas-relief jellyfish from gypsum or acrylic putty make a slightly harder ...

Having a mixed portion of the solution on the wall, immediately proceed to equalizing and forming the relief. We work the edge of the Kelma, masticines, knives, rocks, scalpels - to all that is at hand and that can give the desired shape surface. If during the process it is already dried, but not yet modified, it can be mixed out of the sprayer and try to refine in a few minutes. When you achieve the desired degree of perfection, clean the tank for the knead from the residue and knead the new portion. Note: capacity should be absolutely clean. The slightest particles Will leave scratches.

We form the main reliefs

In the manufacture of a bas-relief, which will be outside the wall will be no more than 2 cm, no reinforcing structures are required. With a greater thickness, in those places where the layer is planned 2 cm, screws are screwed. On them it will be possible to navigate when applying plaster, they will support the solution, without letting it crawl.

Fish and sink have a larger volume - in some places more than 2 cm. Here they screw the screws for reinforcement

In this bas-relief, the most speakers are fish and sink with pearls. In those places where a thick layer will be laid and screw the screws. Pearl roll separately, having blinded the ball and putting it on the self-tapping screw.

The thickest place is head

In places where the relief is assumed to be deep, it is possible to apply a solution at no one, but in several layers. At the same time, it is completely optional to smooth out. The more uneven the surface it turns out, the easier it will impose the following layer. When the required volume is achieved on a certain site (for example, a fish head), we begin work on small details - eyes, mustache, gills, etc.

When elapping small parts, not over 100-200 grams of solution - while cut, align, the solution is seized, therefore large portions are simply not needed.

After the drawing from the putty on the wall is ready, it is left for a couple of days until complete drying. Then you can start grinding - we take sandy paper with an average grain, process, achieving the desired smoothness. When the relief is ready, it is re-made fine-grained emery.

Two days and more, may dry elements with deep relief. Smaller - algae, waves, jellyfish - dry faster. With them and you can start. While they will bring them to mind, dry and thicker details. After the grinding is completely over, we remove dust with a thick brush. If desired, you can spend pressure. Next, covering decorative panel From the plaster in the primer of deep penetration.

The last step of making a bas-relief on the wall - painting. The way of color everyone chooses himself. IN this case used ordinary water produce (the primer was under the paint on water based). This can be considered that you made a bas-relief on the wall with your own hands. In this case, it turned out big composition On two free adjacent walls.

One advice: the bas-relief on the wall looks better with specially designed illumination. So before leveling the wall, output the ends. After aligning and driving the surface, install those lamps with those lamps that will later highlight relief picture. With this light it will be necessary to grind the volumetric panels made by you from plaster mix. Only in this case it will look good. Because if you work with a different lighting, when installing regular luminaires, you can detect a "nightmare and horror".

Bas-relief on the wall: photo ideas

Without experience it is very difficult to understand what and how can I do with the help of ordinary gypsum plaster. In fact, the volumetric paintings from the gypsum can be the most different themes, but the most common - flowers, trees and landscapes (urban, country). In this section, we collected a certain amount of the most diverse bas-reliefs on the wall. With their help, you can imagine the topic for art modeling on the walls. In fact, the process is similar to work with plasticine.

When making the interior of the dwelling, a good solution will be the smearing on the wall. Despite the large number of plaster and plastic products for decorating walls, art Lepak Still remains relevant. This finish is not much of great complexity and it can be easily done independently. This article will consider how to make a laying on the wall with your own hands and what materials for this can be used.

Preparatory procedures

Even the most common stucco from plaster or plaster will give the apartment of uniqueness and elegance. In the design of any room, you can use embossed patterns.

First you need to choose which walls will be applied. It is extremely important to consider the lighting factor whether the light is natural or artificial.

The next stage will be the choice of paintings and places on the wall, where the modeling will be performed.

Newbies in this craft are better not to be taken for complex paintings.

The optimal solution will be images, leaves or colors. An example of such a modeling can be seen in the picture.

It will also be necessary to prepare the following set of tools:

• trowel;
• flat brush;
• palette knife;
• mcList;
• painting tape;
• latex gloves;
• polyethylene film.

It will take the material that is used to align the surfaces.

Bas-relief on the wall

For modeling can be applied various materials. The most common option is to create a bas-relief of plaster and putty.

First you need to choose the most appropriate texture. Beginner leaders are better working with and mixed on the basis of clay. Also for the first time it is better not to draw big images.

A good solution will be the creation of a draft bas-relief on a separate tablet. To do this, you can use wood or plasterboard.

Preparation of drawing

You need to choose the most pro-hand image. The contours are translated on paper, and a plastic film is superimposed on top. And already on top of it the image is applied.

Preparation of the basis

The base of the bas-relief is made of or wax. A layer of plaster with a spatula is applied to a sheet of plasterboard, after which it is aligned.

After about 20 minutes, after solidification of the solution, the picture is being transferred. The stencil from the film is put on the basis and contours of the image are enrolled in a pencil. A relief drawing remains on the cumulative surface, which will after will be moved to the wall.

Creating a picture

This part of the work is the most important and time consuming. A specialist can cope with it quickly, but

the newcomer will need more time. The essence of the procedure is to give the volume of the drawn image.

Creating a volumetric pattern on the wall consists of several stages. The putty is applied on parts of the image not immediately, but gradually, layer behind the layer.

The solution by which the modeling is carried out, is reported to have a high indicator of elasticity and hardening not immediately. Prepare a mixture of the desired consistency is necessary in advance.

Coloring and fixing bas-relief

After the bas-relief is completely sealed, it will take carefully dry. Sharp corners And the edges are processed emery paper. This work should be done with caution in order not to delete too much.

In order for the bas-relief to take the final appearance, its surface will need to handle primer and paint. The primer will allow you to increase the level of adhesion for further painting. For decorative bas-reliefs, it is most often applied water-emulsion paint. The scheme of such a procedure can be seen in the figure.

Gypsum bas-reliefs

How to make a laying of gypsum? This material is suitable for both professionals and beginner artisans. It will be enough to familiarize yourself with the next learning video lesson to simplify the procedure.

Gypsum before use is mixed with PVA glue. This mixture outwardly resembles plasticine to create separate sections of the picture. To obtain a surround image with such a material, it will be enough to purchase the appropriate form in the store. A solution of plaster and glue is poured into it, after you need to wait until it hardens. After hardening, the product is extracted from the form and is attached to the desired part of the apartment.
Optimal lighting - the key to success

You can make a practically any image, but the vegetable compositions are most often selected. A piece of mixed gypsum is chosen, which will be required to create a separate element. The rest of the material must be wrapped in a wet cloth and store in a polyethylene package. This will prevent possible solvent drying.

Newbies often use the image of a grape cluster. To create it, you need to take a sheet of grapes, put it in polyethylene and circling the contours. This will create a template for further work.

After the gypsum is mixed, it takes a small piece of material and is rolled with a rolling pin, after which it is attached to the wall with the help of a slip. The template is placed on the gypsum and drive around the contour. Using the tools, excess material is removed. For these purposes, it is possible to apply both professional devices and faded. First, the contour of the sheet is created, and then its middle.

For creating unique interior You can also use bas-reliefs made with the addition of artificial colors. Flowers, in turn, can be made of tissue or paper material.

To create such a bas-relief in the apartment will be needed in a predetermined tank of a solution of putty with the addition of glue. The consistency of the mixture should externally resemble sour cream or yogurt. Artificial flower Miscellates several times in this solution. The main thing is to follow, so that there are no drums that can quickly dry, and then it will be quite difficult to remove them. After each dipping, a small pause is maintained so that the solution managed to dry a little. After the texture of the figure acquires uniform saturation, the stage can be considered completed.

When the flowers fully solidify, they are attached to the panel with a dense alabaster. From individual sites, a complete composition is created on the entire wall.

As can be seen from the article, there is nothing difficult in creating bas-reliefs and you can do this work. The main thing is to use high-quality materials and tools. Using the photo reviewed earlier, you can pick up suitable option drawing. However, if we plan to model complex patterns consisting of large number Parts, it is recommended to seek help from a professional artist.

Stucco is considered an antique architectural tradition that has been popular yet in Ancient Greece. Despite the variety of existing stylistics for interior design, the desire to equip such a decor, the own home did not disappear and its modern residents.

Let's talk how to make a stucco wall surface with your own hands using inexpensive materials.

What is the stucco?

Once the drawing on the wall surface was created manually. A specially prepared solution was applied by specialists for the plaster and was transformed into original patterns, from where the name is stucco. When forming was invented in the production, the stucco became affordable by the wall decor.

Molds made of metal allow you to create a variety of ornament elements without auxiliary finish. Without loss of high quality, all forms are withstanding at least 2,000 excellent fills.

In the process of creating a stucco, a positive result depends on the quality of the materials used to which:

Gypsum

Ecological, maximum resistant to temperature differences. During hardness, mass from the gypsum becomes more, has properties even penetrate into small gaps. The plasticity of this material facilitates the workflow associated with gypsum design.

Gypsum is not complicated in processing, it is for this reason finished products It is not difficult to give necessary size. When working with stucco from this material, you can mask surface defects, as well as various damage to the elements that often appear during transportation.

When creating a layer of plaster in the workshop of the house, the shape that is filled with a mass is important to shake to eliminate air bubbles.

Facing of the gypsum has its own minuses: considerable weight, which adversely affects the durability of the finish. Also, plaster does not push moisture, but attracts it, which leads to the formation of fungus on the relief.

From such a drawback, you can get rid of if you apply a special protective agent on the stucco.

Polystyrene.

This type of stucco in the interior is characterized by an acceptable cost, but exclusivity can not boast. The decoration is very fragile, requires careful treatment, it is for this reason that it is mainly used to finish the ceiling surface and the top of the wall.

Polystyrene production is carried out automatically. High quality elements are obtained by extrusion from pre-molten composition.

There is no granules in their texture with a pronounced contour available in the foam, which is produced by foaming. Due to this grain, the stucco is deprived of the clarity of the ornament.

Certain forms produce foam extruded, which has a high degree of density, the durability of which is comparable to a polyurethane and an array.

Polyurethane

Get connections required components To obtain a gas formation reaction, resulting in plastic foamed. This material It has a high degree of resistance to temperature drops.

Polyurethane stucco is durable, easy, easy in painting, moisture resistant, has a huge assortment series, does not absorb specific aromas.

On texture and density is similar to a natural array, but unlike it does not change the form and does not crack even after long period time.

Varieties of elements from stucco

From the materials that were discussed above, a wide variety of products are created, as in the photo stucco on the wall surfaces in the represented directory.

Festo and medallions

Festo or garlands imitate the original plant decor and are placed in the top of the wall surface. Medallions are a panel with a pattern of color.

Niche. Installed to wall surfaces, a frame for niches can be purchased separately. Often the bottom of the overhead niches create out of the matte snow-white organic glass, which makes it possible to organize high-quality backlight.

For these purposes, under the glass surface, they set dim lightingwhich effectively illuminating the details equipped in niche, emphasizes their incredible attractiveness, giving the exclusivity of the palette.

Pilasters and columns

Include several parts. The trunks decorated with grooves to make elements elements. Columns from stucco are created in different style performance. As a rule, columns made from polyurethane are intended exclusively for successful wall design, do not carry any load.

However, if necessary, hollow elements can be equipped under carriers. For these purposes, a rack from a metal is placed in the cavity of such a column, which will carry the load.

Columns produced from plaster, in such cases need to be reinforced. Columns from stucco often hide various risers located along the walls in the apartment in a prominent place.

Brackets, pedestals

As for the first elements, they are reliable supports For shelves with books, window sills. It is possible to shut down on the joints of the wall and ceiling surfaces in the form of angular details.

Pedestals are considered supports for decorative accessories. Such a stucco withstands the load of no more than 50 kilograms. Placed on the pedestal ordinary parts look exclusively and significantly.

Like pedestals, and the brackets give the stylistics of the room some highlight, solemnity, add architecture, and also successfully divide the area to the functional space.

In the process of installing such details, it is important not to forget about their proportionality in the ratio of the size of the room. The massive stucco on the wall surface is narrowed by a visually room, and on the contrary - the small stucco can be easily lost in large-sized space.

Dome

Applied as a ceiling decor in Ampire style. You can create a painting on the dome, hiding inside the chandelier, which will become a rather original solution.

Remember, competently selected decor transforms any room. And if there is a stucco to issue a conventional wall surface, then you can get a cozy, extravagant apartments, where many emotions reigns - from rigor to a solemn pomp.

Stock Foto Stucco on the walls

Often this designer acceptance is customary to be used to decorate private houses, where the layout includes. At the same time, the decor can protrude not only in the form, but also as a pattern that the fireplace is moving. In addition, this interior decoration will look great in the door and window Operm, here is the main thing - to choose right size and invoice. The highest aerobatics is a decorative bas-relief that will include the presence of backlight. It will make images more volumetric, creating the impression of 3D graphics.

An important point of use of the embossed decor on the wall - it is not at all necessary for him to have different colors, as it happens in the case of a common painting. The main thing here is to competently select lighting, it will allow to get the selection of various faces of the image, using only artificial lightingAs shown in the photo.

There is an erroneous opinion that the finish of the house with the elements of bas-relief inserts is too expensive. In fact, how to do, bas-relief on the wall with your own hands is quite accessible for beginners. It is clear enough to follow step by step leadershipwhich is presented below. It is supplemented with a video that will allow you to answer many questions arising during the work.

Bas-relief do-it-yourself master class for beginners

People, far from repair, are often mistakenly thinking that such an artistic decor is a prefabricated design, the elements of which are cast from plaster. In fact, it is done manually, and in essence it is really original and unique works of art. Each bas-relief is unique in itself, even if the same sketch is used to create. In principle, the creation of a surround pattern on the wall requires certain skills and skills, as well as thorough compliance with technology, however, it will cope with the task of even beginners.

To begin with, determine the material to create decor. In this process, you can use various options, Suppose, plaster, gypsum, alabaster and even clay. Nevertheless, if you are a newcomer in this activity, it is better to start work so far exclusively by plaster. As a last resort - plaster on a plaster basis.

Master Class Bas-relief flower from plaster shtklanka do it yourself video

After selecting the material, it should be proceeded to create a so-called foundation in which the decorative bas-relief on the wall will be created. To do this, you need to collect wooden drawer With low sides, which will require several rails and plywood as the bottom. The dimensions of the resulting box will coincide with the dimensions of the future decor, it should be considered when assembling it. Replace the box will be able to any box that will have rigid walls and base.

The base of the box should be seen by the film, while it is necessary that the folds are completely absent on it either you should try to make them the minimum. Then it is necessary to prepare a solution, which should be carried out exclusively according to the manufacturer's instructions. Solution B. finished video Flooded in shape. For high drawings, a wire for reinforcement will be required. Bay the mixture to the box, leave it alone for the primary drying, the duration of this period depends on the manufacturer's recommendations.

Bas-relief in the interior photo in the apartment

Now you can proceed directly to the manufacture of bas-relief with your own hands. The main condition here is to create the contour of the future ornament, which then it is necessary to fill out by means of a mixture, which in turn will be prepared again. The volume of the future decor should increase the stage behind the stage, giving each previous layer how to dry. You can draw contours on the surface with the film, covering it surface, after which the film is cleaned.

Master class for novice bas-relief wood video

A very good material will be plaster, since it is very convenient to work with it while it is in a wet state. Thanks to the power of the material, it will be quite possible to remove excess plaster, as well as adjust the form of the future picture. Also, the plaster, which is not dry enough, is easily exposed to Okurization. Do not try to immediately perform several layers, because solidification of each segment is a prerequisite.

In addition, the guide "To create an artistic bas-relief on the wall for beginners" includes the possibility of creating deepening in the future wall panel. The recess is created by two available ways:

• Disparing the material and eliminate some of its part from the finished layout with the help of the chisel.
• Building the background around a certain point, which results in lower.

Most often, the image of the image on the bas-relief is chosen flower, usually lily or tulip. Creating a lily with your own hands initially may seem too difficult task, in fact, this process is at least a beginner. It is important to observe each step of the process, which guarantees the creation of a successful relief.

Bas reliefs Pictures on the walls Design Photo

Often lilies are applied directly on the wall, without creating a base in the form of a box. In this case, the mandatory point is the complete closure of the remaining elements of the interior with the help of painting tape to avoid damage. Next, the future foundation of the drawing must be covered with putty, and then, waiting for its drying, apply primer. It is desirable to use the so-called soil paint as a primer, because it allows you to get a maximum coupling with elements of decorative bas-relief in the future. Drying such a composition of about three hours.

Marseille wax is applied by Kelma, which is a rapidly frozen material suitable for the starting step. With the help of a film attached throughout the surface of the future bas-relief, it is necessary to draw parts. Fixing the film, do not forget about being able to bend freely to be free, for this one edge should be left free.

Bas-relief on the wall in the interior photo in the apartment

Initially, the outlines of the future drawing on the film is possible using a marker. After that, moving the film, followed by the received tracks to pour out future Lily with the help of the same Marseille wax, which will be the most successful material if the painting goes directly along the wall, without using the substrate.

Usually the wax used in operation is characterized by white. To diversify the bas-relief, it is possible to cover the frozen flower with a certain composition. However, the main task of the master is to give the bas-relief maximum realistic. As a finite layer decorative finish Lilies can be used acrylic paints. You must not forget about the finishing layer, which you need to draw every element of the composition.

Master class how to create a flower on a video wall lesson

As can be seen from the leadership above, the bas-relief on the wall is an interesting process, but laborious, to create it with your own hands. Beginner masters will need a bit of adequacy and attention, as well as the exact following technology. It is important here - stock attention and necessary tools.