Why is the cold water pipe wet. Why condensation forms on cold water pipes and what to do: effective methods to fix the problem

The occurrence of condensate on the pipes of cold water supply is quite common. Both metal and plastic pipes are most covered with moisture in the summer: in order to effectively overcome this problem, it is important to understand the exact cause of its origin.

Why condensation occurs

The main reasons for cold pipe humidification are:

1. If we are talking about a cold water riser, in this case, condensate will form on an ongoing basis, up to the appearance of puddles on the floor. The reason may be a leak in one or more pipes in the upper neighbor's apartment. Often the whole thing is in an unreliable toilet tank. To clarify this, it is best to choose the night time, when it is possible to hear well the fall of drops along the sewer riser. Condensation on hot water pipes usually does not occur.
2. When there is no exhaust ventilation. The same may be due to interruptions in her work. This problem often affects new buildings or dwellings where there are metal-plastic windows: in such cases, there may be no hood if the windows are tightly closed. To determine the difference, a simple experiment is carried out by applying a newspaper to the ventilation grill, opening and then closing the windows. If there is no exhaust ventilation, sometimes the additional fan is powerless.
3. If condensation is observed on the plastic pipes that are included in the apartment wiring, quite often the reason lies in the breakdown of the plumbing fixture, with insufficient or completely absent hood.

Condensation on the pipes in the toilet

Condensation on the cold water pipes in the toilet can occur due to high humidity or temperature fluctuations. If this problem is detected, ventilation is first checked: for this, you can leave the door to the room open at night. If during this time the moisture on the pipes disappears, then it's all about poor ventilation. Another potential cause is the constant flow of water through the tank.

This leads to the effect of cooling the pipe, since there is no time left for heating the water inside it. As a result, the surface of the pipe becomes a comfortable place for moisture condensation. Usually, after repairing the taps and the inlet valve, the problem disappears.

Condensation in the bathroom on cold water pipes

Before starting repair measures, it is important to determine exactly the cause of the problem, which usually consists of the following:

• When the riser pipe gets wet, the whole thing is usually the flow of the neighbors from above.
• If a pipe gets wet near a plumbing fixture, then the reason lies in a faulty faucet.
• If ventilation problems are found, work will need to be done to eliminate blockages blocking the hood.

If condensation appears in the bathroom on the pipes: what to do in such cases? Listing ways to eliminate condensate, one cannot help but recall thermal insulation, which quite effectively helps in this problem.

In case this material is not available, it can be replaced by a simple polyurethane foam. For this, a corrugation with a diameter slightly larger than the diameter of the problematic pipe is taken, and cut into separate sections, convenient for installation on communication. After putting on the corrugations, its inner space foams.

How to install thermal insulation on your own

Insulating cold water pipes from condensate is quite easy to do on your own.

This will require the following consumables:

• sanding paper.
• Rust converter.
• Strong thick thread.
• Fabric strip 50-60 mm wide.
• Epoxy putty.
• Acetone.
• spatula.

1. Sand the insulated section of the pipeline to improve its adhesive properties.
2. Pouring a little acetone on a rag, degrease the surface.
3. Apply phosphoric acid for corrosion protection.
4. After the pipe is completely dry, an epoxy putty of a thick consistency is applied to its surface (it is important that the material does not drain)
5. Without waiting for the substance to harden, you need to quickly wind the fabric using good tension. To fix the last turn, a prepared thick thread is used. During this procedure, it is very important that the turns of the fabric completely overlap each other, and the putty completely soaks them.
6. After waiting until the putty is completely dry, according to the same scheme, you need to apply a couple more layers of thermal insulation. The final coating will be a layer of epoxy material.
7. When the finish dries, the pipe can be sanded and painted.

Elimination of condensate on the pipeline

To eliminate this unpleasant phenomenon, one of the following methods can be used:

1. Troubleshooting the ventilation system. Insufficient ventilation can not only lead to condensation on the pipes: it is important to remember that such conditions can provoke the formation of mold, which is very harmful to breathing and can cause many diseases. To enhance passive ventilation, an additional forced manual fan is usually used. In addition, automation can be installed, to turn on which a timer or hygrometer is used.
2. The reason may also lie in large temperature fluctuations in the room and the water supply: because of this, the surfaces with which cold water is in direct contact fog up. In the future, the accumulation of moisture can develop into streams flowing to the floor. In this case, good thermal insulation of the cold pipeline helps, which is easiest to do with the help of special tubular material (thermoflex, energy flex, polyethylene foam). This insulation is available in several sizes. When selecting, you need to focus on the indicator of the inner diameter, which should be equal to the diameter of the pipeline. The tube is cut along the entire length, followed by pulling on the pipe and gluing the seam. For these purposes, it is best to use a special metallized adhesive tape of a permanent type.

The indoor climate is often directly affected by weather conditions in the form of prolonged rains, or the specifics of the local climate. This is especially true for areas near large rivers, lakes, seas or oceans. In this case, even the highest quality waterproofing of the house will not help: it is much more efficient to use dehumidifiers or air conditioners that have a similar function. It should be said that the struggle to normalize the humidity inside the home is useful not only in terms of combating condensate: it will also have a beneficial effect on the safety of the interior decoration and the health of the inhabitants of the house.

Condensation can almost always be observed on cold water pipes. This phenomenon not only spoils the appearance of the bathroom to some extent, but can cause serious problems. Constantly wet tubular elements have a limited service life.

Therefore, such a problem should be solved very quickly. In this case, questions arise about what to do if drops of water are found on the pipeline and how to remove condensate from cold water pipes. First, there is no need to over-dramatize the situation. Secondly, you need to familiarize yourself with all the methods for eliminating this problem. Thirdly, choose the most optimal option and put it into practice.

Causes of condensation

Condensation on cold water pipes can appear for the following reasons:

• The presence of a source of high humidity in the room.
• Insufficient ventilation.
• Water supply pipes have poor quality thermal insulation.
• Temperature changes. For this reason, in the summer, there may be a stronger formation of condensate, which simply flows down the surface of the pipes.

The main part of the reasons for the formation of condensate does not require explanation. As for the first item from the list, some clarifications are required.

Sources of high humidity include the following:

• Problems arising in the process of functioning of communication systems and buildings. These can be steam from cooking, evaporation from wet laundry, a flooded basement, a pipe failure, and a clogged vent.
• Defects in the building resulting from a violation of construction technology.
• Geographical features of the region: the proximity of large bodies of water or high levels of humidity in combination with rocky soil, which contributes to the formation of condensate.
• Unfavorable natural phenomena: sleet, prolonged rains or humid climate of the area.

Prerequisites for the appearance of condensate on cold water pipes

In most cases, condensate appears on pipes located in bathrooms. Despite the specifics of these rooms, it is not only for this reason that the pipes become wet.

There are a number of factors that can cause condensation to form on the pipes in a toilet:

• Insufficient ventilation. To determine that condensation appears precisely because of this, it is enough to leave the doors to the toilet open at night. If the pipeline turns out to be dry in the morning, then you should repair the ventilation system and make it better.
• Constant flow of water in the tank due to a malfunction of the valve. This leads to the fact that the pipeline begins to cool, resulting in a greater accumulation of condensate on its surface. A simple repair of the inlet valve and tank taps will help fix the problem.
• Leak in the toilet of the neighbors living on the top floor. In this case, you need to inform the owners about the situation. In their absence, you can temporarily eliminate the condensate with your own hands. To do this, the section of the pipeline, on which the accumulation of water drops is found, is wrapped with a bandage in several layers and one end of the winding is lowered into a container, the accumulated water is regularly poured out. See also: "".

The accumulation of water on the cold water pipes in the bathroom can occur in the following situations:

• Incorrect location of the water supply system. If the pipes of hot and cold water supply pass close enough to each other and do not have thermal insulation, then accumulation of water droplets is observed on the elements through which cold water flows. The way out of this situation is to ensure high-quality thermal insulation of pipe elements using suitable materials.
• Mixer failure. If water constantly drips from the tap, the overall temperature of the working medium decreases, which leads to cooling of the pipes and the formation of condensate on their surface. Repairing the mixer will help solve the problem.

How to remove condensate, how to wrap pipes

For those who have encountered such a phenomenon, the question immediately arises of how to wrap the pipe so that there is no condensate. There are several ways to prevent the appearance of water droplets on the surface of cold water supply pipes, one of which is thermal insulation. This option is considered the most effective, as it eliminates the cause of their appearance - a temperature drop. The easiest and fastest way to resolve the issue is by means of an insulating tube, cutting it lengthwise for convenient placement. For the manufacture of the tube, polyethylene foam, energy flex or thermoflex is used.

There is another way to deal with condensate on tubular elements, but it is considered more complicated. Using this option requires the following materials: epoxy putty, acetone, rust remover, sanding paper, spatula, nylon thread and strips of fabric about 5 cm wide.

The process looks like this:

• The pipe is cleaned with sanding paper to improve surface adhesion.
• Degrease the skinned area with acetone.
• The surface is treated with a rust remover and allowed to dry (read also: "").
• A thick epoxy putty is applied to the pipe and wrapped with strips of fabric. The edges are fixed with a thread.
• Another layer of putty is applied on top and again wrapped with a cloth.
• Cover the fabric with putty and leave to dry completely.
• After all layers have dried, the pipe is sanded and painted.

In the event that drops of water appear as a result of a malfunction of the plastic pipeline, you can independently replace the damaged section of the pipeline with a new elbow. Metal pipelines can only be replaced by plumbers with special equipment and skills.

To prevent condensation on plastic cold water pipes, the following types of insulating materials are recommended:

• Styrofoam or expanded polystyrene is considered a universal insulation for pipelines made of polymeric materials. It comes in the form of a shell, consisting of two halves. They are connected to each other by means of a tongue-and-groove lock. The use of such insulation is quite simple: the shell halves are put on the pipe and fixed with adhesive tape.
• Mineral wool for pipeline insulation is produced in rolls, which greatly simplifies the use of this material.
• Polyurethane foam refers to heaters with high insulating characteristics. The temperature range of such a material is quite wide, from -160 0 C to +150 0 C. Almost all polypropylene pipes have such a layer, it is formed on products during the production process. In this case, the thickness of the insulation reaches 5 cm.

Chemical elements that help get rid of condensate

Products of the chemical industry help to protect cold water supply pipes from condensate formation: Stermizol, Korund, Teplomett and others.

The use of these insulating compounds implies the following actions:

• The pipe is cleaned of dirt and rust.
• Apply a layer of primer for better adhesion of the insulation to the surface and leave to dry.
• Using a roller, brush or spray, cover the surface with a protective mixture. The most effective is the application of 5 layers of insulation, and each layer must dry well before the next application. The optimal drying time for such mixtures is about 1 hour.
• A special fixer helps to extend the service life of a heat-insulated pipeline, which in parallel will make the pipes more attractive.

Which method to use to deal with condensate on cold water pipes depends on the reasons for the formation of this phenomenon and the specific operating conditions. It is very important to consider how often the problem occurs, as well as at what stage it is.

Condensate drain - condensate trap

To remove the formed condensate in automatic mode, a float-operated condensate trap is used. This device is installed at the outlet of the apparatus that provides heat exchange, including water heaters and heaters. Through such a technical device, the water accumulated in the system simply evaporates.

Steam traps fall into three main groups:

• Combined devices.
• thermostatic.
• Float.

The operation of float type steam traps is based on the use of the difference between the density of condensate and steam. These devices are very popular due to the large number of positive characteristics.

The main advantages of this type of device are the following:

• High degree of reliability.
• Excellent performance figures.
• Possibility of work at the minimum loadings.
• No need for condensate cooling.
• Resistant to sudden temperature changes.
• Uninterrupted operation under increased loads.

It is also impossible not to note the optimal energy saving indicators of thermal systems with float-type steam traps.

To deal with condensate, you can choose any of the following methods. In most cases, their use helps to eliminate unwanted moisture. If these options are not effective enough, it is possible to get rid of the formation of condensate on cold water pipes by waterproofing all surfaces of the room. High-quality performance of this type of work is possible only with special knowledge and skills.

Moisture often appears on the pipelines of one's own houses, less often apartments, which in some cases is barely noticeable, in others it causes great inconvenience. There are factors that can influence the intensity of an unpleasant process and reduce the scale of the consequences that inevitably follow.

The need to make early repairs with the replacement of pipelines intimidates any owner who imagines the inevitable financial costs and discomfort. Therefore, there is a desire to figure out in advance why condensation forms on cold water pipes and take preventive measures.

Causes of condensation

Condensation in your house or apartment in a multi-storey building is like morning dew on meadow grasses, which forms during wet weather with large temperature fluctuations. In a dry hot summer with warm nights, the foliage cannot “cry” due to unsuitable conditions for this.

Steam will condense under the following circumstances:

• increased concentration of moisture in the air space;
• large temperature difference between air and solid base.

If the bathroom is warm and humid, and the pipeline is cooled by constantly flowing cold water, it will be difficult, almost impossible, to deal with condensate.

It is possible to avoid the appearance of moisture on the pipes of the central riser and the intra-apartment plumbing only through the adoption of comprehensive measures, without which the metal or plastic will constantly sweat. Before you understand what to do against strong condensate on cold water pipes, you need to establish all the reasons that cause it to form.

It is possible that the drain system in the tank is constantly leaking in the toilet, therefore, cold water flows through the pipeline all the time, causing it to become hypothermic. In a multi-storey building, leaks in apartments located above can cause condensation on the riser, so you will have to discuss the problem with your neighbors. Residents of private homes are quite able to deal with problems on their own.

In any case, you should check the efficiency of air exchange in the room, clean the ventilation grilles, windows, pipes. Excess moisture settles not only on pipes, but also on walls, furniture, ceiling, which leads to damage to finishes and property.

Overheating of the air around pipes with cold water, the formation of condensate on them can be facilitated by improper installation of the water supply system. If the hot water pipe is located too close to the usual cold water pipe, it is likely that the latter will easily sweat. Therefore, it is very important to invite qualified specialists who have knowledge of the standard distances between pipes for the initial installation work, then you will not have to get rid of problems during operation.

It happens that everything is checked, done correctly, and condensate on pipes with cold water still forms regularly. Then you have to take special additional measures that will help get rid of the problem.

What does it threaten

The temptation is great to ignore the formation of condensate, not to try to get rid of it immediately, to wait until everything normalizes by itself. The idea is good, but in this case it can lead to unpleasant consequences.

Constantly wet metal pipes easily rust and deteriorate, moreover, they are a stimulant for the reproduction of microbes and mold fungi. Plastic pipelines with condensate do not undergo oxidation, but are a source of deterioration in the sanitary condition of the apartment, so the problem must be eliminated.

You can remove moisture by wiping the cold water pipeline and puddles under it every morning, but in practice no one will do it - it is too long, difficult and unpleasant. In many hard-to-reach places in the toilet or bathroom, it is generally impossible to get rid of condensate by simple cleaning, so the wet surface is constantly stored there and causes harm.

Important! The colonization of a room with mold fungi can harm health, it is much easier to get rid of condensate immediately after it is detected, to prevent the reproduction of microorganisms.

So, the reasons for the appearance of moisture on pipes with cold water have been established, what can be done next, how to get rid of it - you should think about it.

Application of thermal insulation

To reduce the temperature drop on the surface of the pipeline, you can use a layer of thermal insulation. The easiest way is to take special tubes made of foamed polymer materials, cut them lengthwise and fix them with wire on the pipeline, which will not sweat after the procedure. In order for the insulation to be guaranteed successful, it is necessary to select the diameter of the polymer product according to the dimensions of the cold water pipeline. Too wide or narrow layer of heat insulator will not help to completely get rid of condensate.

Advice! With a not very large difference in the temperatures of pipes and air, it is possible to isolate the metal surface by applying a special liquid composition - anticondensate.

The mass is well distributed with a roller, brushes, dries, forming a durable protective layer. There are several brands of products that insulate pipes, the composition and structure of the composites are similar, so the method of use is the same. Painting with the product must be carried out several times. Manufacturers recommend applying a layer in 5 stages with a difference of at least 1 hour, which allows the liquid mass to dry well, and subsequently get rid of condensate.

If funds for the purchase of polymeric materials are not enough, you can get by with improvised materials. To do this, the pipe is well dried, cleaned of rust, degreased with acetone, puttied. Then, on a wet layer of putty mass, a layer of old fabric, gauze, rags is fixed by wrapping. From above, a pipe insulated in this way can be wrapped with ropes or cords, wait until it dries completely and paint. The whole procedure does not require the cost of expensive materials, is performed independently without much effort, allows you to get rid of condensate for a long time.

Installing the hood

In bathrooms, kitchens, bathrooms of multi-storey buildings, a centralized ventilation system is built in, the capabilities of which should be enough to maintain normal air exchange in the apartment. In practice, it often happens that it works inefficiently. If in kitchens with gas stoves the state of air outflow is controlled by employees of the city gas services during scheduled visits, then no one monitors this in the bathroom and toilet.

To normalize the exchange of air flows, reduce humidity, an exhaust system should be installed at the repair stage, and it should be regularly turned on as a rule. The device is not so expensive, and the result will be visible to the naked eye, allowing you to quickly get rid of condensate.

Condensate drains

In the sanitary rooms of private houses, water or air heaters are sometimes installed, the operation of which is based on heat exchange processes. The units must be equipped with an efficient condensate drainage system, otherwise the humidity in the room will increase significantly, which makes it very difficult to get rid of condensate on cold water pipes.

There are several types of devices for removing condensed water, the most effective is the float type. The unit demonstrates high efficiency with minimal energy consumption, which attracted the attention of a large number of consumers.

If condensation constantly forms on cold water pipes, it is unwise to turn a blind eye to this, there are several reliable ways to get rid of the problem. They differ in the amount of funds needed to eliminate moisture in the pipelines, the degree of complexity of the troubleshooting work. Each owner is able to assess the acceptability of one or another option for a set of specific circumstances, to choose the necessary and affordable one.

Condensation forms on cold water pipes - what to do?

Droplets of condensate on cold water pipes are common, especially in summer when the air is heated to high temperatures. Droplets collect in streams and often puddles form on the floor next to the water supply pipe.

How to get rid of condensate, prevent corrosion of the pipeline, eliminate the fungus that occurs from moisture?

Causes of condensation on pipes

During the repair of the premises, especially with constant high humidity, it is worth taking care of communications in advance. Condensation on pipes, both metal and plastic, can occur for the following reasons:

1. Leakage plumbing as a result of improper installation, or in the process of wear.
2. Weak ventilation, improperly organized humid air exhaust system. Blockages in the ventilation system will lead to excess moisture on the surfaces of the room.
3. Leak in the plumbing system, neighbors' toilet bowls.
4. A sharp temperature drop in the room where condensate collects. The situation is especially deplorable in summer, when water literally flows over the surface of the pipeline.
5. Configurations of distributing cold, hot water supply. If they are not thermally insulated, but are located close to each other, condensation is inevitable.

How to get rid of condensation?

If moisture accumulates on the riser, it is possible that the neighbors have a mixer, a toilet bowl, and other plumbing. This can be tested at night, when the characteristic sounds of flowing water are heard in silence. The problem with ventilation is observed when the windows are locked, especially those equipped with metal-plastic bags. Checking the operation of the system is easy.

It is enough to take a sheet of paper, attach it to the hood, clogging the windows, then do the same with the doors open. If there is no ventilation, the visual effect is obvious.

If moisture is concentrated on the apartment's wiring pipes, the reasons may be as follows. Faulty plumbing fixtures directly in the apartment may be to blame. The second reason is poor air circulation, especially in rooms with constant high humidity.

If the cold water pipe leading to the plumbing gets wet, the faucet, the shower faucet, the inlet valve of the tank in the toilet are to blame. When the riser is constantly getting wet, you need to look for the problem of water pipes from the neighbors from above. If the ventilation is clogged, it is worth checking the air circulation in it.

How to eliminate condensate?

You can get rid of the problem in several ways:

1. Check the hood, remove debris, cobwebs from there, then buy a compact fan, install it instead of the ventilation grill. Manufacturers offer a wide range of similar devices, different in price, power.
2. Isolate the water supply system with special insulating tubes with a cut, which are available in building supermarkets. They are made of energy flex, polyethylene foam, the ends are fixed with permanent metallized tape. This method is the easiest, fastest, but before insulating the pipeline must be thoroughly dried.
3. Complete isolation will provide the following method. First, the pipe is plastered, after which the surface is wiped with acetone, then with a rust converter. After drying the pipeline, it is covered with epoxy putty and quickly wrapped with strips of fabric in 2-3 layers, the edges of the fabric are fixed with a clamp, wire. Then the epoxy putty is applied again, after drying, the surface is sanded, covered with paint.

Caustic soda for sewer cleaning - pros and cons.

Methods for protecting metal pipelines

If condensation is not removed from the metal pipes of cold water supply, corrosion will cover them over time. What can be done in this case:

1. First, the surface of the pipes is cleaned of rust, then dried, covered with drying oil, oil paint.
2. You can use carbolate, a paste-like mass for sealing cracks in floors and walls. The composition is applied to the surface with a 5 mm layer, left to harden for 24 hours. After that, it is sanded with fine-grained sandpaper, painted with oil paint.
3. Protective primers can be used, consisting of zinc dust diluted with drying oil, epoxy varnishes. They cover the surface of the pipe, after that they are painted with paints, enamels.
4. The pipeline in the toilet can be coated with a composition based on drying oil, minium in a ratio of 20:80 or primers such as GF-031, FL-03K, FL-053, GF-021.

If we are talking about a bathroom, here for painting hot pipelines, heated towel rails, oil-resistant enamels are used, for cold ones - any enamels, paints.

How else can you deal with condensation?

The following is a good way to fix the problem. It is necessary to put on the pipeline a corrugation with a diameter larger than that of the pipe, then fill the cavity between the surfaces with mounting foam. If puddles form on the floor, in the place where condensate accumulates, a sleeve made of pipes several diameters larger than the wiring itself will help get rid of them. The system is simple, while it will not interfere with the repair, replacement of the pipeline in the future.

Dehumidifiers sold in appliance supermarkets are a great way to deal with the problem. They are a plastic box inside which an absorbent tablet is placed. The absorber will relieve not only of condensate on the pipe, but also eliminate humidity in the entire room.

A more expensive option is to install an air conditioner with climate control, which will ensure the optimal level of humidity.

It is advisable to waterproof the floor of the bathroom, toilet, which will help to cope with the problem of condensation on pipes and surfaces. If this method of repair is not feasible, it is worth opening windows after taking a hot shower, taking a bath, opening the bathroom doors. The circulation of cool air will quickly eliminate the accumulated condensate, help to effectively cope with moisture on the pipes.

Based on the practical experience of dealing with condensate on pipes, the masters advise the following:

1. Yuri Rogov, a plumber, recommends buying Gofroterm, a special compound sold in specialized stores. It is applied to the surface of the pipe, after which a strong elastic film is formed on it, which prevents the formation of moisture.
2. Andrey Kazantsev, foreman of the production site, advises to purchase liquid thermal insulation, which is applied like paint to the dried, cleaned surface of the pipeline. According to him, this method is better than thermoflex, other insulating materials.
3. If the ventilation, plumbing, plumbing is in good order, the cause of the accumulation of condensate may be the temperature difference between the pipe and the air. Locksmith Nikolai Korotkov advises in this case to conduct insulation. To do this, you will need long covers of polyethylene foam, or merylon, hollow inside, which are sold in hardware stores. They are put on the pipeline, fixed at the bottom with a wire, a clamp.

There are various ways to get rid of fogging of the cold water supply pipeline. Which one to choose should be determined after analyzing the situation.

Plumbing work, if you have a tool, experience, you can do it yourself, as an option - seek help from specialists.

http://postwater.ru

A serious problem in the cold season is the occurrence of condensate on the cold water supply pipes. The release of dew drops can be quite significant, which leads to increased corrosion of steel pipes and does not bode well for plastic and polypropylene pipelines.

Condensation on pipes can appear as a result of the following factors:

• Increased air humidity;
• Insufficient ventilation of the room;
• Faulty pipes, plumbing valves and taps;
• Temperature instability.

Content:

If, for one reason or another, condensate appears on cold water pipes, our article will tell you what to do in the situation that has arisen. First of all, it is necessary to clearly understand what a serious problem the appearance of dew is for the water supply. The presence of additional moisture on the pipes leads not only to the loss of an attractive appearance, but also is fraught with failure of pipelines and flooding.

Causes and consequences of condensation on the pipe

Condensation in the bathroom is most likely due to temperature fluctuations and high humidity that occurs while taking a bath or shower.

As for the toilet, this is most likely the case here. As a result of the constant replacement of water, its temperature remains significantly lower than the ambient temperature, which leads to cooling of the walls of the tank, resulting in a temperature drop and the occurrence of condensate on the pipes.

The consequences of drops not eliminated in a timely manner, both for water supply and for sewage, can be very deplorable.

First of all, the flow of droplets down under the action of gravity leads to the creation of favorable conditions at the base for the formation of various. With increased dampness, bacteria and molds will actively increase the population, so it will be far from easy to destroy them later.

Metal pipes of cold water supply, upon contact with drops, rust intensively, plastic and polypropylene pipes lose their attractive appearance. The constant presence of dew drops adversely affects all types of finishing materials.

Regular flow to the base of the pipe, of course, will not cause a spontaneous flood in the apartment, but the water wears away the stone and sooner or later certain problems will arise there, which is unlikely to have a favorable effect on good neighborly relations. In addition, the accumulated condensate at the base of the pipes, with a high degree of probability, will render such a floor covering as unusable, or linoleum.

As can be seen from the above, the consequences of an untimely reaction to the presence of condensate on pipes can be quite serious, so we will consider possible methods to prevent its occurrence. The fact is that the prevention is cheaper than the elimination of the destruction caused by this unpleasant phenomenon.

How to get rid of condensation from cold water pipes

In modern construction, water supply can be mounted both from steel, and from plastic and polypropylene materials. Depending on the material of the pipeline, there are various methods of dealing with additional moisture.

How to remove condensation from a plastic pipe

Although the appearance of dew drops on plastic is unlikely to lead to failure of the water supply system, nevertheless, negative consequences cannot be avoided.

If moisture forms on plastic hot and cold water pipes, you can get rid of condensate using one of the following methods:

• To improve air circulation, replace the hood with forced ventilation;
• Carry out thermal insulation using special polyethylene tubular insulation designed specifically for plastic and polypropylene pipes;
• If the room is subject to a sharp temperature drop, the solution may be to use a special tread primer, which can significantly reduce the formation of condensate on the surface of the pipe.

We get rid of moisture on metal pipes of cold water supply

The resulting condensate on metal pipelines is more dangerous than in the case of using plastic water pipes. The fact is that in addition to the loss of aesthetic indicators, in the case of using metal, its corrosion destruction can occur. Consider the popular protection methods:

• The first, most simple and effective step to get rid of condensate is to clean the pipe from various contaminants, degrease, dry and cover with oil paint;
• Next, you should treat with a waterproof sealant the gaps at the points of contact of the pipes with the floor, ceiling and in other likely places;
• The entire pipeline is treated with a protective compound and coated with enamel, in addition, it is possible to use insulating materials.

Having carefully studied the essence of the problem, condensate on cold water pipes, what to do now is more or less clear, but it should be noted that it is worth trying to prevent the occurrence of condensate through preventive measures. This is due to the fact that it is much more difficult and expensive to eliminate the possible consequences of the appearance of dew.