Ceiling tiles diagonally. How to glue ceiling tiles diagonally - gluing rules

landscaping 29.08.2019
landscaping

Pasting the ceiling with tiles seems to be a very simple job. The main thing in this business is correct calculations, accurate marking, and a neat sticker of the central four plates. The ceiling covering can be laid not only straight, but also obliquely. It looks interesting, extraordinary, and at the same time it will slightly mask the curvature of the walls. This article will tell you how to glue the ceiling tiles diagonally.

The ceiling is finished with white ceiling tiles

What you need to know

Important

Before you go to purchase material, you need to find out the footage of the ceiling and calculate required amount coatings. Standard sizes tiles 50x50 cm, that is, for one square meter the ceiling will need four tiles.

In this case, it should be borne in mind that a certain part of the tile will go to undercuts, alignment and fitting of the pattern. And if you decide to glue it diagonally, spending facing material will increase by another 15-20%.

Ceiling surface preparation

Before you start any decoration of the ceiling, you need to prepare it for this.

  • The surface should be freed from the remnants of old paint or other coatings.
  • Prime the ceiling twice. The second primer is applied only after the final drying of the first layer.

    Before starting installation, we make a primer on the ceiling

  • After the ceiling has dried well, markings are needed that will orient the laying of the tiles so that it goes neatly and economically.

markup

You can not beautifully glue the tiles diagonally from corner to corner. Correctly, if the tile lies relative to the walls of the room at an angle of 45 degrees. For perfect installation, you need to start marking from the middle of the ceiling.

Be sure to check its accuracy once or twice. It is easier to double-check the result than to redo the spoiled work later.

1 - marking for pasting diagonally; 2 - marking for parallel pasting;

  • Stick ceiling tiles should be from the middle of the ceiling or from the chandelier.
  • Glue is applied around the perimeter of each tile very carefully, and a drop is added to the middle without smearing it.

Apply glue to the tile around the perimeter

How to install tiles correctly:

  • The size of the pieces is calculated separately and depends on the area and geometry of the ceiling. If necessary, cut the tiles against the wall with a sharp knife, although it is best to make every effort to make the most of each tile.
  • So that the adhesive on the coating does not spoil the view, it is necessary to remove it from the surface immediately during the cladding.
  • Using a ruler and a knife, cut out pieces to glue the small remaining sections on the sides of the ceiling. If you do this with a calculation, then from one tile you can get a certain number of pieces suitable for business.
  • If the master accurately marked the ceiling and set to work strictly from the middle, then the cut pieces on opposite sides ceilings must be exactly the same.

When the center is the chandelier

Sometimes it is better to start marking from the chandelier, even if its location does not coincide with the center of the ceiling. Under the chandelier there will be joints of the first 4 plates.

  • The scheme in this case is as follows: we outline a rectangle on the ceiling and divide it with diagonal lines. The only thing you need to check is that the center of the rectangle is defined correctly and corresponds to the attachment point lighting device.
  • The diagonals of the square crossed at the attachment point of the chandelier. From this point, work should begin, distributing the starting four plates so that their edges run parallel to the diagonal lines of the rectangle, and the tops converge at the point of attachment of the lighting device.
  • It is quite possible that the corners of the first four plates, converged in the center, will have to be cut off a little. This probability is directly dependent on the configuration of the chandelier. The cut edges of the tiles will be hidden after work is completed. decorative element chandelier or the chandelier itself. The main thing here is to cut the corners as accurately and accurately as possible.
  • Then we continue gluing, coordinating each next tile along the side of the previous one.

The final stage of work

  • In order to give the tiled composition a complete look, you need to use a special ceiling plinth, which can be glued with the same paste as the cladding. If its width is approximately 3.5 cm, then it will help hide small flaws around the perimeter of the room.
  • Then you need to take a damp cloth and remove the remaining glue and all pencil marks from the surface.
  • At the end of the work, it is useful to check whether all the tiles are well stuck to the ceiling. In case something went wrong, it is necessary to immediately correct possible errors.

Outcome

If you don’t like it when cut pieces on the sides remain from all edges, then you need to very accurately calculate the number of tiles based on its size and the parameters of the room. It does not make sense to use the method of diagonally laying the ceiling slab if a seamless coating is used. As you can see, working with ceiling tiles is not so laborious, it does not require large physical and financial costs. A person who does not even have professional skills in construction and interior decoration will be able to cope with this work.

opotolkax.com

How to glue ceiling tiles diagonally

Ceiling tiles can be laid not only in a straight line relative to the walls. Styrofoam tiles laid diagonally not only look original, but also hide the curvature of the walls, which naturally can not be mated at right angles. As a rule, this method is the solution to many problems. It makes no sense to lay tiles diagonally only if you have a seamless one.

It must be borne in mind that sometimes the base of the ceiling itself can shine through the seams, therefore, before laying it, it is necessary to prime it with a deep penetration primer. If any dark spots appear on the ceiling, then you need to paint over them with white water-based paint.

It will be easier for beginners in the construction business to glue white ceiling tiles, because after gluing the seams are easily masked with finishing putty. After the ceiling can be painted several times with water-based paint of any color. The paint will hide all defects - soiled seams and fingerprints. Besides, white tiles can be glued on glue putty - it is much more convenient and reliable than celluloid glue. If you have purchased a colored ceiling tile, then you will need to work with it very carefully, since all the flaws will be very clearly visible.

Laying ceiling tiles diagonally is practically no different from conventional scheme. Here the main rule is to correctly mark the ceiling.

So, in order to properly glue the ceiling tiles diagonally, we do the following:

1. Determine the center of the ceiling. To do this, we draw two mutually perpendicular lines connecting the midpoints of parallel walls.

2. We glue the first ceiling tile in the center so that its corners are aligned with the drawn axes.

4. We lay the rest of the ceiling surface with solid tiles.

  1. We cut out the necessary pieces for gluing the small remaining area along the edges of the ceiling. If cut sparingly, several pieces can be obtained from one tile.

After the entire surface of the ceiling has been pasted over, remove any remaining glue and pencil marks from the tiles with a damp cloth.

If necessary (if the ceiling tiles are white), you can putty the seams, glue the ceiling plinth and paint the updated ceiling with water-based paint in several layers.

You can learn the general principle of working with ceiling tiles from our article “Installation of a ceiling made of polystyrene tiles”.

www.diy.ru

How to properly and quickly glue the ceiling tiles diagonally

Have you already decided to finish the ceiling with polystyrene tiles, but do not like standard solutions? In this case, there are two ways to avoid banality: you can combine plates of different colors, or you can stick them in an unusual pattern, for example, diagonally. How to glue the ceiling tiles diagonally, you will learn from this article. The diagonal scheme is especially useful if in some part of the room the walls “collapse” - after all, unlike the usual one, diagonal gluing does not emphasize this defect.

Materials and tools

For work you will need:


It looks like a diagonal way of gluing with sealing seams with sealant

You need to purchase the following materials:

  • Ceiling tiles in the right amount with the addition of a few pieces for cutting.

With diagonal gluing, there is much more waste than when working in the usual way. The tile should be with seams, because seamless will not allow you to evaluate the unusual location of the material on the ceiling, because the seams will not be visible. Ordinary white square slabs work well, which can then be painted with water-based paint to mask fingerprints and glue stains.

Advice. It should be painted as soon as possible after gluing, ideally on the same day. If you postpone painting for a couple of weeks, then it will become more difficult, because a little dust will already settle on the ceiling, and if this is a kitchen, then soot.

  • Glue will be offered to you in the store along with the tiles.

Most likely it will look like a clear liquid in a plastic bottle. It will be inconvenient to work with such glue, because the plates will have to be held at the top with your hands for a long time. In addition, it will not allow you to align them relative to each other in height and the quality of work will not be ideal. It is more convenient to use glue putty, in this case you can adjust the thickness of the glue layer and at the same time putty the gaps between the plates.


Oblique intersecting lines at the top optically push the walls apart

Do-it-yourself glue preparation

You can make a good adhesive putty yourself. To do this, approximately 10% PVA glue is added to the usual finishing or acrylic putty. So, for example, 150 g of PVA building glue should be added to a one and a half kilogram bucket of putty. Dry putty (in powder form) is first diluted with water according to the instructions on the package, and only then the glue is poured.

Surface preparation

First of all, you need to carefully prepare the surface: clean old whitewash or water emulsion, sweep dust from the surface, you can even wash it. Extensive cavities are puttied, the protrusions are cut off. Cracks and seams are sealed with plaster, you can use reinforcing tape for this. Be sure to walk along the ceiling with a deep penetration primer. Any will do: acrylic, polymer, dispersion, antiseptic - all of them are deeply absorbed into the base, fastening its layers together, improve the quality of the finish, prevent dampness and the development of microorganisms.

Through thin tiles, spots on the base ceiling can be seen through. In this case, it will be enough to apply one layer of white water-based emulsion on it.

Step-by-step instruction

Ceiling markings

The quality of all subsequent work depends on this crucial stage, so measurements should be taken with all care. Marking is done with a paint cord. Working with it involves the presence of a second person, but if there is nowhere to take an assistant, you will have to drive some fasteners (nails, concrete screws) into the ceiling in the right places, on which you can fix the second end of the cord.


gluing tiles

You can start gluing. We apply liquid glue around the entire perimeter and a few drops in the center, spread the glue-putty with a spatula. If Titanium and its analogues are used, the tile must be pressed against the ceiling, removed and pressed again after a minute, finally. This operation makes the liquid adhesive thicker, the finish will hold more securely. If glue gets on the front side, remove it immediately damp cloth.


Once all the materials are dry, you can paint the ceiling and reinforce the ceiling plinth.

Video lesson: glue the ceiling tiles diagonally

Knowing how to glue the ceiling tiles diagonally, you can diversify the finishes with this inexpensive material, make the design of the room much more interesting and at the same time hide small defects in the proportions of the room.

toppotolok.su

How best to glue the ceiling tiles diagonally: video

Tile diagonally

Ceiling tiles (see Armstrog Ceiling Tiles) are a great solution for those who do not want to deal with complex and lengthy repairs, as they are easy to use, functional and have a good service factor. It is very valuable to know some practical advice, which you will inevitably encounter when decorating the ceiling with tiles with your own hands.

Ceiling tiles serve as a good finishing material and are appropriate in almost any room - living rooms, kitchens, corridors and even bathrooms. You choosed suitable color and the size of the product, and before you the question is how to glue the ceiling tiles diagonally?

What tools and glue to choose? Below you will read detailed guide on finishing work using tiles.

Choosing glue

We start, as usual, with the purchase the right materials so that later at the last moment you don’t realize that something was missing, something was missed and we will create conditions in which it will be easy and fast to work.


Adhesive for polystyrene tiles

Mounting adhesive is represented on the market by many companies that specialize in the manufacture of adhesive masses for specific purposes. We need ceiling tile adhesive (see Can I stick ceiling tiles on whitewash?), so it's better to buy the most popular type - "TITAN Wild".

Choosing a tile

The adhesive has good performance and does not pose a threat to humans, made from natural high-tech raw materials. Acceptable cost, fast sticking and quality of work are significant qualities when choosing an adhesive.


Ceiling tiles - a high-quality and inexpensive solution

Before we start gluing tiles on the ceiling diagonally, first of all we will choose the right one depending on the type of our room and its design solution (see Design of plasterboard ceilings in the hall). Most cheap option- polystyrene tiles.

Buying a tile from this material, you get:

  • Safety;
  • Versatility;
  • Ease of installation and weight;
  • The minimum thickness is no more than 10 mm.

Such tiles are durable and easy to use, but the coating is difficult to wash and accumulates dust.

Polystyrene tiles are available in three types:

  • Pressed;
  • Injection;
  • extruded.

Pressed tile is the most affordable material today, but the least durable. Injection tiles make an impression easily seamless ceiling, and also copes with noise and heat insulation.

Tiles as a way to decorate the ceiling

Extruded tiles are the most durable and are covered with a special film that can be washed, vacuumed or made wet cleaning. The range of colors among polystyrene boards is very rich - how to choose the right color?

Depending on the space, hardware stores offer a wide range of textures and patterns.

Tiles are produced white color, but:

  • You can draw a picture on it;
  • colorize special paint;
  • Pick up an imitation of wood, fabric or wood.

The decorative properties of the tiles are rich and suitable for any kind of premises.

Before you glue the tiles diagonally, you can watch a short video clip about the installation process.

Finishing work

Agree, not everyone is satisfied with pasting with plates exactly, parallel to the walls, and I want something new.

To do this, people resort to various design solutions, for example:

  • Tiles laid diagonally;
  • Non-standard masonry;
  • Combination of types;
  • Combination different colors plates, etc.

We will look at how to stick tiles on the ceiling diagonally and thereby kill two birds with one stone - the room will noticeably change, and you will practice on your own.

Keep in mind that ceiling tiles are rarely glued to whitewash!

Ceiling markings

In both cases of masonry, the ceiling tiles are glued in the same way, but the markings are of particular importance - even luggage will depend on this condition. In order for the tile to lay flat, we start marking from the middle of the ceiling. Usually there is a chandelier hanging there, but you may not have it:

  • We draw four lines from the midpoint to the corners of the room
  • Divide the four corners in half and get 450.

Ceiling marking instructions

Thus, these lines will become the main reference point in pasting the ceiling with tiles, and the installation will shift by 450 relative to the walls.

Advice! It should be taken into account that when choosing a tile, it is better to be guided by the size of the room where the repair is supposed to be. It is not always wise to use non-standard masonry, but in any case, you need to know how to glue tiles diagonally in a large room.

doing repairs!

Trained by Andrey Belotkach,

repair specialist

apartments, Perm.

FREE PHOTO LESSONS

APARTMENT REPAIR ◊

1. How to putty a crack

2. How to quickly seal a seam

3. We make out the arch

4. Close the pipes in the kitchen

5. How to cut drywall

6. How to align the corners of the walls

7. We glue the ceiling tiles

8. Install double doors

9. Plasterboard ceiling

10. Making a stretch ceiling

11. Self-adhesive film

12. Drywall in the bathroom

13. Align the slopes at the window

14. Making a box in the bathroom

15. Making a mezzanine

16. The secret of puttying joints

17. Remove yellow spots

18. Perfect layer transition

19. Why you need a chipper

20. Wiring

21. Repair sequence

22. Decorating the corners of the tiles

23. Eliminate repair defects

24. Decoration of old doors

25. Ceiling moldings

26. We fix the plinth on the bath

27. We paint doors with high quality

28. Ceiling curtain

29. Making a box with a hatch

30. Install the outlet

31. Towel dryer

32. Repair cracks in frames

33. and ceiling plinth

34. Installation of the ceiling in the bathroom

35. We fix the threshold at the door

36. Wall insulation

REPAIR TIPS

1. Ceiling option No. 1

2. Ceiling option No. 2

3. Ceiling option No. 3

4. Ceiling option No. 4

5. Ceiling option No. 5

6. How to check the quality

7. Dismantling sockets

8. Puttying Tips

9. How to choose a sealant

10. What glue for wallpaper

11. What paint to paint

12. How to choose linoleum

13. Lack of laminate

14. How to attach platbands

15. DIY repair

How to glue ceiling tiles diagonally. construction portal diy.ru

  • How to make a pendant with your own handsOften to show your loved ones how dear they are to us...
  • How to build a tree house Who did not dream of a tree house as a child? If the dream is...
  • Do-it-yourself window renovation: paint an aluminum profile aluminum profile are reliable, beautiful...
  • We cook delicious mushrooms: pickled mushrooms, two recipes Mushrooms this summer are apparently invisible. Two hours in our forests...
  • Insulation with expanded polystyrene. Features of the use of polystyrene in private construction Modern heaters can be divided into two types...
  • How to choose a gun for polyurethane foam. polyurethane foam in construction and repair Among the considerable number of tools in demand in everyday ...
  • How to install a built-in vacuum cleanerBuilt-in vacuum cleaners appeared on Russian market about 10 l...
  • How and where to buy material for handmade onlineOften visitors of our portal are interested in where you can buy...

Ceiling decoration is attached great importance, as it is a completely open area in the interior. You can offer beautifully, elegantly decorate it with ceiling tiles. Let's get acquainted how to stick a ceiling tile on a diagonal.

Geometrically, the sides of a room are not always perfectly parallel. The diagonal arrangement of elements on the ceiling surface visually hides this.

Today's building materials market is represented in huge assortment on design ceilings. It can be different kinds installation of ceiling systems or more affordable materials.

Not everyone can install elite stretch ceiling. And an inexpensive tile will help out many. Try sticking ceiling tiles with your own hands. The main thing is to be careful when calculating and careful when pasting. In addition to the aesthetic side, it provides better soundproofing, which is important in apartments of multi-storey buildings.

If there are small cracks, irregularities on the surface, then the tile finish will hide them, visually the room will become larger. You can stick it on suspended structure(from mineral fiber, plasterboard, acoustic version).

The material of ceiling tiles can be made of wood, metal, mirror, which makes interesting element into the interior. The seamless option gives the surface solidity. We will consider the most common option, the cheapest and most used products from foam tiles.

Before we learn how to stick a ceiling tile diagonally, we will briefly consider its types depending on the production technology and composition.

Types of ceiling tiles

  • Injection tiles - during their production, the initial components are exposed to high temperatures during the technological process. In this case, the output is a thicker product, which allows you to give it a more voluminous, deep relief.
    This is a seamless model that creates a single picture, without seams, as when pasting individual elements. It has the correct geometry, improved sound insulation characteristics, it can be painted with water-dispersed paints, and is unpretentious in maintenance.
  • Extruded tiles are among the most durable products of this type. Manufactured by pressing polystyrene strips. It is smooth or laminated, which makes it possible to care for it using water with detergent solutions. Thanks to slightly concave edges, it successfully hides the flaws of the plane.
  • Stamped tiles are the cheapest products and strength characteristics they have the lowest. They are produced by pressing, fragile, which requires delicate handling. However, if you glue, paint the ceiling tiles with high quality, they look quite good, they can be wiped with a sponge.

Which ceiling tile is better to choose - it's up to each of you. Pasting is carried out according to one technology, but depends on the chosen method. Hence the different surface markings.

Ceiling preparation

First of all, clean it from the previous coating. Remove old wallpaper, a layer of whitewash, paint, other coatings. If the overlap has irregularities, then level it with putty.

The surface must be even so that the tiles stick well, there are no gaps between the elements. If the surface is even, but there are cracks, small chips, other damage on it, seal them with putty, prime them.

You can lay the tiles parallel to the walls. Today we will analyze how to stick the ceiling tiles diagonally. This is dictated mainly when there is a curvature of the walls.

When laying along the walls, this nuance will be immediately noticeable, while the diagonal arrangement will smooth out all the bumps. The same can be said if the room is of the wrong configuration. And for aesthetic reasons, the diagonal method looks very advantageous in the interior.

Correctly calculate the required amount of material. The best option it will be if you sketch and lay the tiles to size on paper to scale. Or take the area of ​​\u200b\u200bthe ceiling (floor) plus 15-20% as the initial amount (with the diagonal method of sticking the material, it takes a little more).

All tiles should be checked upon purchase for even edges, loose structure, pattern matching. Items must be from the same batch. Let the tile after the acquisition get used to the future conditions of its residence a little. It will take indicators of humidity, room temperature, so that after installation its geometry does not change, there is no deformation.

Ceiling markings

You need to find the center of the room - the sticker will be drawn from it. If the lamp (chandelier) located in the room is not located in the middle, then we will markup from the location of the chandelier.

In any scenario, the center is determined by dividing the ceiling with two perpendicular lines coming from the middle opposite walls. It turns out four rectangles or squares.

For safety net, beginners can additionally beat off the lines dividing the right angle of each rectangle in half. The plane is puffed up, divided into eight parts with equal angles at 45 degrees.

Diagonal ceiling tile sticker

Consider it yourself technological process how to stick a ceiling tile diagonally. It differs from the sticker parallel to the walls with markings, the direction of the corners of the tiles, and a slightly higher consumption of material.

Choose the right one for the job adhesive composition, there are enough of them in stock. It should not contain a solvent (for foam tiles). Often used are "Liquid nails", "Eco - carries", "Moment - installation", "Titan", "Dragon", other compositions. Many use a special mastic or prepare the adhesive mass themselves by mixing putty with PVA.

Apply glue dotted along the edges of the tiles plus, connecting opposite corners diagonally or dotted along the entire reverse side - it all depends on the composition chosen, follow the manufacturer's instructions.

First glue along the axes

The first tile should be placed at the intersection of the axes so that its corners coincide with the marking lines. Squeeze it and hold it for a while. Next, you need to stick the next tile along the marking line, joining the corner of the first with the next.

From the axes you conduct further pasting

According to this principle, the label is carried out diagonally along all guide lines. It remains to fill the gaps between the tiles laid along the guides. And so the entire surface. From time to time, check the correct position of the elements relative to the markup.

When you come to the walls, then in place, cut out the extensions and glue them. Remove the adhesive composition that has come out with a sponge. If small cracks have formed somewhere, then you can putty them with putty, seal them with sealant.

Having eliminated drafts, let the tile dry well, frame it with a baguette, then you can proceed to painting it. We have considered the main steps on how to stick a ceiling tile diagonally. It remains to choose the tiles you like and decorate your interior with it.

Ceiling decoration with ceiling tiles is popular among people who prefer to do their own repairs and not spend a lot of money on it. However, to make the ceiling look beautiful, you should follow certain rules when gluing.

Diagonal styling features

There are three types of foam tiles, any of which is suitable for installation:

  1. Pressed. It has a democratic price, a variety of textures and colors.
  2. Injection or seamless. You need to glue it in accordance with the arrows on the wrong side. More expensive and denser. It is difficult for a beginner to use for decoration with a rhombus, because even the slightest deviation in the calculation will immediately affect the design of the ceiling.
  3. extruded. An expensive option with smooth surface and wide colors. More suitable for rooms with high humidity.

The most popular materials for decorating the ceiling in an apartment are foam materials. Styrofoam tiles are inexpensive, easy to clean, and soft enough to be cut.

Gluing ceiling tiles diagonally or with a rhombus has a number of features that must be considered when choosing a mounting method:

  • Such placement involves precise marking of the ceiling and accurate cutting of the material. Process diagonal laying will require patience and a large number time.
  • During installation, you can easily hide irregularities and other surface imperfections, which will be more noticeable with parallel gluing.
  • When choosing, it must be taken into account that for diagonal laying it is better to use plates with seams. Seamless models are more suitable for the option when the fragments are stacked parallel in a row.
  • Diamond layout requires cutting a significant part of the material, the trimmings of which may be unsuitable for further use. Unintentional damage to tiles often occurs, which increases consumption and material costs respectively.
  • The combination of material of various colors and textures can create a bright and unusual interior.

Material calculation for diagonal layout

The size of a foam tile is 50x50 cm, that is, its area will be 0.25 m².

The easiest way to perform the calculation is if the room is square or has the shape of a rectangle. It is enough to multiply the length by the width and divide this value by 0.25. The resulting figure will show the required number of tiles for finishing the ceiling. It is more difficult to calculate the material for custom sizes or if you plan to create a complex pattern. For unusual shape rooms should measure all sides, draw up a diagram on paper, enter the values ​​\u200b\u200bthere, add them up and divide them into the area of ​​​​one tile.

For laying diagonally, with the calculation of trimming, it is necessary to purchase 15-20% more material.

Ceiling markings

It is possible to glue the ceiling tiles with a rhombus only after marking the surface. It is made using a paint cord from the center of the room or from a chandelier.

From the center

To determine the center of the ceiling, you need to draw two straight lines from the midpoints of opposite walls. The resulting four corners of 90 ° divided in half at 45 °, they will be the direction for gluing the tiles.

From the chandelier

If the light source is not located strictly in the center, for beauty it is better to take its location as a starting point, and not the middle of the room. The markup differs from the chandelier in that the lines do not pass through the center of the ceiling, but through the place where the lighting device is attached. Depending on the pattern of the material, the chandelier will be located at the junction of a rhombus of four plates or in the center of one fragment.

The markup should be double-checked, since the beauty and accuracy of the final result depends on its accuracy.

Where to start tiling

To make the ceiling look aesthetically pleasing, it is more correct to glue the ceiling tiles diagonally from the center.

Often in apartments, the chandelier may not be located in the middle, then the markings should be carried out from it, so as not to violate the geometric symmetry of the room.

glue ceiling tiles you can also from the corner of the room, but you need to follow certain rules:

  1. Cut the material diagonally.
  2. Glue half of the fragment to the corner.
  3. Next, attach the whole tile with its side to the cut side.
  4. Following this algorithm, decorate the remaining surface.

How to glue tiles diagonally

Before starting work, you will need to prepare the following tools:

  • stationery knife for cutting material;
  • glue;
  • a simple pencil for marking;
  • dry cloth to remove glue residue and pencil lines.

Glue the ceiling covering with a rhombus can be both square and rectangular.

Before installation, carefully prepare the surface:

  1. Remove the old coating to ensure perfect adhesion of the material to the ceiling.
  2. Putty all the bumps and cracks.
  3. Prime the ceiling twice. This will prevent mold and mildew from growing under the material and help the adhesive adhere to the surface. Only after complete drying can you proceed with the design of the tiled coating.

Glue on the tile should be applied along the edges without smearing, retreating a few centimeters so that it does not leak out when applied to the surface. If this happens, immediately remove the excess with a dry cloth. Place one drop in the center.

At different types Adhesive bonding time is different, therefore, in order for the tiled coating to hold well, you must strictly follow the instructions. Usually, to achieve maximum adhesion, it is enough to wait 2-3 minutes and only then attach the fragment to the ceiling for 15 seconds. This applies to universal glue (Master, Titan and others). In addition to it, you can use liquid nails (Moment). They should also close up various cracks or seams. The price, in comparison with universal glue, is much higher, more and more consumption.

You can also use acrylic putty, it should be applied to the material with a spatula. It is suitable for sealing seams and small discrepancies. Many do not even realize that this is the cheapest and convenient option for sticking tiles.

In order to correctly glue the ceiling tiles diagonally, it is important to lay the first one in the center so that its edges strictly coincide with the lines drawn from the walls. It is from the competent location that the beauty of the picture will depend.

For work, we need the following tools: a long (at least 50 cm), preferably a metal ruler, a stationery knife and a simple pencil.

It is better to start the ceiling tile sticker from the center of the room, more precisely from the chandelier. Under the chandelier, we will have a junction of four central tiles. Of course, you can make it so that it is in the center of a separate tile, but this already depends on the pattern on the tile. If the pattern is the same as in the first photo below, then it is better to place the chandelier in the center of the tile. If the drawing is the same as in the photo at the end of the article, or there is no drawing at all, then better chandelier will look at the crosshairs of the four central tiles.

Why do we start from the center? At the edges of the room, in any case, the tile will not be entirely, it will have to be cut off. And if you start the sticker from the corner, then on two walls the tiles will be entirely, and on two - trimmings. Asymmetrical. Sometimes asymmetry looks even better, but in our case it will look ugly.

To enlarge, click on the photo

Here, the center of the room is chosen as the starting point. Due to this, the tile is slightly offset relative to the chandelier, which, if you look closely, does not look very nice. Although you can not look closely.

Ceiling markings for ceiling tiles

Sticker tiles diagonally - this is by no means "from corner to corner." Tiles should lie at an angle of 45 degrees to the walls. The room is most often oblong, and if you draw a line "from corner to corner", then the angle of this line to the wall will be far from 45 degrees.

I somehow unknowingly drew a line "from corner to corner" and tried glue tiles. Having pasted a few pieces, he was horrified and tore them all off.

Naturally, a protractor for finding right angle we will not use. This is done much easier. First, remove the chandelier and find a point in its very center (point BUT). From this point we measure the distance to the nearest wall (distance C), trying to maintain a right angle (deviation plus or minus 1 cm is not critical). Then the same distance (distance C) set aside from the corner of the room to the wall farthest from the chandelier (we find the point B, see figure).

Now from the point B draw a line to the center of the chandelier. You can do this this way: pull the twine between two points (an assistant will be required) and put a few points on the ceiling with a pencil so that there is enough ruler length between them. After that, consistently draw a line along the ruler. Everything, our markup is ready.

Ceiling preparation

Before you begin to work on the sticker of the ceiling tiles, you need to prepare. We mean that we have a fairly even whitewashed ceiling.

First, let's get rid of the dust. This can be done with a vacuum cleaner. Then we apply one or two coats of primer to the ceiling. I usually prime twice, but a single primer will be enough. Once the primer is dry, you can start tiling.

Ceiling tile sticker

For ceiling tiles, I usually use TITAN ceiling adhesive. It is inexpensive and of good quality.

The glue is applied along the perimeter of the tile with a strip of 2-3 cm, and a spot is made in the center with a diameter of 10 cm. It is convenient to apply the glue as follows: slightly evenly pressing on the bottle, at the same time smear it with a valve in small circular motions. It is desirable that there are no places not covered by glue along the edges of the tile.

After applying the adhesive to the tile, allow it to dry for a couple of minutes, after which the tile can be glued.

It is very important to stick the first four tiles evenly. But it is even more important to stick the first tile evenly. To do this, set one corner of the tile as accurately as possible to the point BUT, while the opposite angle must exactly coincide with the line drawn by us.

After the tile has been applied, it should be held for a minute, pressing it against the ceiling. You can press the tiles with light strokes using a soft cloth.

Now glue the remaining three tiles. It should be noted, however, that some manufacturers ceiling tiles make the corners slightly rounded. This is imperceptible to the eye, however, if this is not taken into account, it will turn out uneven. Therefore, we try on each next tile not in one of the corners, but completely along the edge of the tile.

For the same reason, it is better to glue the remaining three central tiles at the same time, well, or one immediately after the other so that you can correct their position relative to each other on the spot. Otherwise, the last of the four tiles may either not fit into the space allotted for it, or, conversely, there will be too much gap between the tiles.

Everything, the beginning is necessary, further it will be easier. The same way glue the rest of the tiles around the central ones. It is better to glue all the whole tiles first, and then those that need to be cut (along the perimeter of the room). The edge, cut tiles do not have to fit too closely to the wall. Ceiling plinth, whose width is 3.5 cm, will hide small flaws.

At ceiling tile sticker it is often necessary to bypass . To do this, a groove is cut in the tile with a width of a couple of millimeters less than the diameter of the pipe. This is done so that there is no gap between the tile and the pipe. The groove must be rounded at the end (under the pipe).

After gluing the tiles, a small piece of tile is glued into the remaining space between the pipe and the wall. If the distance between the pipe and the wall allows you to glue the plinth there, then this piece is not necessary to glue.

Mounting ceiling plinth

Glue ceiling molding quite simple, but here you need to take into account some nuances.

Glue can be used the same - TITANIUM. Glue is applied in the same way as on the tile - in circular motions over the entire contact surface. After applying the glue, we wait a couple of minutes, and put the plinth in the right place, press it until it is fixed.

When sticking a plinth, you should not forget about the drawing on it, if it is, of course. The drawing needs to match. Often a plinth comes across, which by mistake can be glued “upside down” (such is the pattern on it), and here you need to be careful.

The hardest thing about ceiling plinth installation are internal and outside corners. In order not to create unnecessary problems with the corners, I recommend using special corner elements. They can be both simple, shaped like a plinth, and made in the form of decoration.

The use of corner elements allows you not to suffer with cutting a complex angle on the plinth. Usually the shape of the corner elements is such that the plinth is glued to them with even factory (or also trimmed) ends.

And last tip: If you don't want the freshly pasted white to be covered with gray spots, wash your hands often during the process of pasting it. If not after each glued tile, then after three or four for sure. And keep the cloth clean if you use it to press ceiling tiles or baseboards.

We recommend reading

Top