How to glue wallpaper in the corners - the secret to perfect gluing. How to glue wallpaper in the corners: design features How to stick wallpaper on the outer corner

Wall decoration with wallpaper is the most popular option for decorating walls in rooms. Undoubtedly, wallpapering on smooth walls this is quite elementary and requires only a little skill, but wallpapering the corners of the room is technically more difficult. Before sticking wallpaper with your own hands, you need to properly prepare the walls.

First you need to clean off old wallpaper or paint, apply primer to the walls and level their surface. And only then begin to paste over the corners with wallpaper.

So, repair specialists distinguish the following stages of this process:

1. You need to start by aligning the corners, for this you can use putty and, after it dries, clean up sandpaper. In order for the angle to be even, you can use special device- a plastic corner that is attached to the putty. Remember that if you don't get rid of uneven surfaces wallpaper may come off.
2. The next step is to apply glue - before gluing the wallpaper into the corner of the room, you must very carefully glue the entire height of the corner with glue. If the roller does not cope with its task and leaves unsmeared fates, it is worth using a brush.
3. Direct wallpapering of corners with wallpaper - there are different lessons of specialists that help to properly wallpaper the corner of a room, it is worth listening to them, but for greater productivity, we will outline some of the features of this stage: competent finishers do not recommend gluing wallpaper in the corners with whole strips, this is due to the fact that they can distortions will appear and the joints will be uneven.
4. The wallpaper canvas must be cut so that their side from the sides extends 50 mm onto the adjacent wall.

Glue must be applied to the strip of wallpaper and the corner of the wall. Next, you need to attach the wallpaper to the corner of the wall as follows - if the pasting process starts from left to right, then the left side is applied to inside corner for even coverage.

At this stage, you need to clearly understand that you need to wallpaper the outer and inner corners in different ways.

outside corner

External corners can be glued in two ways: firstly, if the outer corner has a flat surface, you can not waste time on leveling it and immediately apply wallpaper to the corner, then use the level and measure the edge of the strip so that the remaining strips lie evenly; secondly, to glue the outer corners, you first need to lead the strip around the corner by 4-5 cm, and glue the next part of the wallpaper at the top. Using a clerical knife and a ruler, cut these layers vertically.

Inner corner

Internal corners require more attention. Wallpaper must be glued so that they go onto the adjacent surface by about 3 cm, but not more, otherwise they will go wrinkled. The fold and turn of the wallpaper must be coated with glue. Next, you need to measure the width of the wallpaper located on the adjacent wall, mark the allowance of the glued side, which is glued at a distance of about 2 cm from the corner and a vertical line is drawn through it with a plumb line - this will mark the edge of the glued wallpaper.

Alignment of the wallpaper is done by rolling, for this there are special rollers and spatulas.

All the above stages of wallpaper stickers in the corners go sequentially.

Corners on the walls on the wallpaper: what is it

plastic corners on wallpapers are a good finish for finishing corners - they have protective functions and give the corner a finished look.

Construction markets offer different decorative corners:

• Corners with a width of 20 × 20 to 50 × 50 mm are suitable for corners that are subject to heavy wear;
• Dimensions 10 × 10 or 15 × 15 mm will give a neat finished look to the wall - they are called decorative corners;
• The corners may differ in color, may have the texture of wood or metal.

For arched outer corners, it is better to use corners with the following approximate dimensions: 5×17.7×17.10×20 and 15×25 mm. Plastic corners are recommended to be mounted using silicone sealant, it is colorless and has a good grip. The length of the corners varies from 3 to 7 m, so it can be adjusted to individual sizes.

Plastic decorative corners help protect wallpaper from mechanical damage at the corners of the wall, in addition, they are not expensive and easy to install.

How to glue wallpaper in non-woven corners: features and tips

Non-woven wallpaper is particularly durable, but working with them is quite difficult, especially on corner surfaces, because. they are not elastic.

To paste over the corner of the wall with such wallpaper, when cutting off part of the wallpaper, it is necessary to make an allowance of 1.5 cm, this allowance must overlap.

Need to know little secret- sticking non-woven wallpaper will be easier if you make equal cuts along their entire length along their edge.

Glue in this case is applied only to the wall, and the wallpaper must remain dry. In the work on decorating the corner with such wallpaper, it is better to first use the corner, then unnecessary crooked places will not appear. If the choice is made in favor of wallpaper with a pattern, in this case it is necessary to qualitatively adjust the pattern in the corners. In order to keep the pattern in the corners intact, you need to cut the next strip from the corner to fit the pattern of the already pasted wall.

Here are some tips:

• It is necessary to make a small overlap on another wall;
• It is better to hide the joints at the top of the corner;
• Wallpaper with a pattern in the corners is better to glue on a plumb line.

Meter wallpaper is a wide non-woven fabric a little over a meter. This type of wallpaper helps to paste over faster big apartment and pattern selection becomes easier. In order to stick meter-long wallpaper in the corners, you need to overlap up to 3 cm on the next wall. The rest of the procedure will not differ from the standard pasting of corners, which is described above.

How to glue corners on wallpaper: installation technique

Then proceed according to the following plan:

1. The adhesion of the corners to the wall will be stronger if they are glued to the wall, and not to the wallpaper;
2. Distribute adhesive material evenly on the inside of the corner;
3. Attach and press to the desired area on the wall, remove excess glue with a napkin;
4. Do not touch the corners until the material is completely dry.
5. In order for the sealant to better grab on the site, you can fix the corner with adhesive tape.

How to glue wallpaper in the corners (video)

So, knowing the technology of wallpapering in the corners, you can perform quality repair with their own hands and in addition to help relatives in this difficult matter.

In the article you can find the answer to the question of how to glue wallpaper in the corners. It is worth taking the finishing process with all responsibility, irregularities can be striking, thereby spoiling the impression of a freshly made repair.

Step-by-step instructions for gluing inner corners

When finishing main problem uneven walls and the resulting folds on the wallpaper can become. It should also be borne in mind that with curved walls, the joints wallpaper may diverge.

How to glue the outer corner (outer)?

The protruding corner must be pasted over by analogy with the internal one, however, there are slight differences that must also be taken into account when working.

What to do if the corners are uneven?

Uneven walls are a common problem in old houses. Before you start gluing the finish coat, it is advisable to carry out preparatory work and bring the surfaces "in order". If visually the corners are even and do not require overhaul, it will be enough to walk with a hard cloth, removing small bumps and dust. If the irregularities are visible to the naked eye, then it is better to do a little work before you start gluing the wallpaper.

Features of gluing meter wallpaper

Wide canvases are convenient in that they allow you to finish with fewer seams on the surface. Gluing them is more difficult, but the result is worth it.

How to join in corners?

It would seem that such a trifle as gluing corners in a room can completely ruin all the work if done incorrectly. And if there is also a pattern on the wallpaper that needs to be customized, then you should approach the finish responsibly.

How to adjust the pattern in the corners?

It is important that the pattern is continuous and even around the entire perimeter of the room. To do this, you need to correctly combine the pattern, and cut off the excess.

1. The strips are also overlapped. Leave an allowance for both walls.
2. With a plastic spatula, the wallpaper is pressed against the corner.
3. After gluing the second canvas, the wallpaper is cut according to the pattern. This method applies to wallpaper with a small pattern. For a large pattern, trimming around the edges may be required.

Before gluing, you must first prepare the material for work by spreading the floor covering and studying the pattern. Segments are cut off after selecting the pattern in height.

Features trimming wallpaper in the corners

In order to get a perfectly even seam in the corner, you need to properly trim the excess.

1. After the wallpaper is pasted to the wall, a flat metal ruler is applied, it can also be a spatula or a rule. To make the cut line even, you can use the level.
2. With a sharp clerical knife, cut off the excess along the edge of the ruler, after which upper layer wallpaper will come off.
3. The bottom layer of wallpaper is carefully tucked in and removed, removed in the same way.
4. The canvases are smeared with glue and pressed tightly against the corner. As a result, the coatings fit snugly together.

Gluing wallpaper in the corners is not so difficult, but special care and accuracy is required. Today there is a finishing method that allows you to work without joints at all, namely liquid wallpaper. They are applied in an even layer and do not require such complexities as adjusting the pattern, width, accuracy in rounded places and other nuances.

Tsugunov Anton Valerievich

Reading time: 4 minutes

Wallpaper is a universal finishing material, the main advantage of which is the relative ease of working with it. With their sticking, you can successfully cope on your own, without resorting to the help of specialists. But if a decision is made to transform the appearance of the room on your own, it is important to understand how to properly glue the wallpaper in the corners. It is this part of the work that is the most difficult.

Preparatory activities

Criteria for choosing wallpaper for uneven walls and corners

If there is no desire or opportunity to engage in leveling the base, you need to approach more carefully.

• The material for curved surfaces should be loose so that the joints where the overlapping strips will have to be glued are not conspicuous. Non-woven fabrics are well suited.
• The drawing should be small and frequent or completely absent.
• The unevenness of the walls will help hide the material with a relief structure.
• For heavily damaged surfaces, fiberglass wallpaper is suitable for painting.

Work materials

Tip: do not start gluing wallpaper from the corner, to start work, select a flat part of the wall.

Experts have their own secrets for pasting corner elements.

• I glue it on. When gluing wallpaper in a butt corner, there is a risk of the canvases diverge after drying and the appearance of a gap that cannot be quietly removed.
• We do not glue the whole canvas, even if the corner is perfectly even. Otherwise, after drying, folds and distortions are almost inevitably formed.
• Coat the wall with glue. It is in the corners that the probability of material lagging is especially high, therefore this rule applies to all types of canvases: paper, non-woven, vinyl.

Wallpapering inside corners

For pasting the inner corner, follow the following procedure.

• We measure the distance from the edge of the strip that was last pasted on the wall to the corner. We add 2 cm to the obtained value. We cut the canvas, bend it according to the added allowance and transfer it to the wall smeared with glue. The excess must go to the adjacent side. The glued sheet must be smoothed with a roller or a rag so that all the air comes out from under it.

• We also bend the second sheet by 2 cm and glue it on the other side of the corner so that the allowance overlaps on the previously glued sheet. The correctness of gluing this canvas must be checked with a plumb line. While smoothing the sheet, we try not to press those very few centimeters of the allowance.

• We don’t need two layers of wallpaper, they will stand out, so we apply a long ruler to the corner and cut the layers along it construction knife. Then remove the excess top coat.
• Raising the top layer, remove the lower segments, coat its edge again with glue and press it tightly against the wall, squeezing out the air. This method allows you to get a very even butt joint.

Wallpapering in outer corners

To wallpaper the outer corner with wallpaper, you need to calculate the width of the canvas so that the sheet, bending around the ledge, passes to the adjacent wall by 2–5 cm. Having measured the required width of the canvas, cut off the excess part. Remember that when using too wide a strip, we will inevitably get folds and wrinkles.

• We apply glue both on the wallpaper and on the wall. We apply the sheet to the ledge so that the canvas wraps around it, as in the next photo. If the material is dense, you need to make small cuts for good contact with an angle.

• We press the sheet in its upper part. At the bottom of the excess canvas we make an incision. If the material for gluing is smooth, smooth it with a roller, press the embossed one with a cloth. The part of the strip that has gone around the turn can be cut off, leaving a small edge.

• We take next sheet or the remainder of the previous one and paste it the same way to the adjacent wall. The canvas should overlap on the first layer. Using a plumb line, we check the verticality of this strip, if necessary, we combine the pattern. Carefully smooth out the fabric.

Wallpaper is the most common finishing method in our country. interior spaces, especially apartments and living rooms in private houses. However, there are several difficult moments where the majority makes mistakes and spoils the impression of the repair as a whole. One of these moments is working with corner elements, and we will tell you how to properly paste wallpaper in the corners.

Glue wallpaper in the corners

Why is it important to know

There are several reasons why we decided to write about corner areas and their wallpapering.

If there are usually no problems with the rest, even parts of the walls, then here we see the following picture:

• It is at the joints of the walls that crumpled, broken, torn, peeling or swollen wallpapers are most often observed. Take a closer look at the wallpaper pasted with your own hands at friends or at home, and you will notice such a pattern;
• Angled lines are the most prominent and noticeable elements of the room, this is a kind of indicator of the quality of the finisher's work. If there are problems there, they will definitely be noticed, and this will spoil the whole impression of;
• AT apartment buildings, as in private ones, there is a significant deviation in the geometry of the walls and their relative position, verticality and planar orientation from the drawing norm . As a result, we get not quite right angles and not quite even walls, and when two adjacent walls are uneven, each in its own way, then the line of contact between them can even surprise you with its shape;
• Finally, most novice repairmen are interested in this particular part of the work on decorating the room with wallpaper.

Important!
All of the above phenomena lead to the fact that even expensive coatings with good rough plaster and the presence of leveling putty, they do not guarantee a quality repair.
With all the dignity and beauty of the main part of the wall surface, a few flaws in the corner areas spoil the whole picture and make your work look like an amateurish one.

Wherein straight lines between the walls, even with inexpensive materials, they look solid and give the impression of masterful work and a professional approach. Therefore, for those who have to repair, it will be useful to know how to properly glue the wallpaper on the corners.

Internal

In rooms, it is the inner corners that are more common, there are at least four of them if the room is rectangular. Therefore, maximum attention should be paid to them.

We have compiled an instruction that will help you easily deal with the part of the room method:

1. When you start working, stick the first strip at a distance from the inner corner, equal to the width of one strip (roll). Then move from this place along a flat wall;

1. When approaching the next turn, stop when it is less than one lane wide. Take the next piece of wallpaper and cut it in width so that it wraps 2 cm onto the adjacent wall at its thinnest point (if the overlap is uneven);

1. Lubricate the strip and the wall and stick a piece of canvas, gently wrapping it around the turn and pressing it to the surface. Roll it with a roller or smooth it so that there are no wrinkles. If the edge line on the wrapped edge is not vertical, this is not a problem, the main thing is that there are no folds in the corner part;

1. On an adjacent wall, draw a plumb line at a distance of the width of one strip of wallpaper. Apply glue to the wall and strip and stick a piece of canvas, attaching its edge to this line. An overlap of at least 2 cm wide will occur between the canvases;

1. Find the thinnest point of the overlap of the strips, divide it in half and from this point draw a vertical line along the entire overlap under the plumb line. Attach a metal ruler or rule to this line and cut through both canvases with a sharp construction or clerical knife;

1. Remove the piece of the covering strip, then carefully bend its edge and remove the piece of the covered strip. Coat both edges of the canvases with glue and carefully roll them to the wall. You should get a perfectly even joint without cracks or sagging.

Important!
When cutting the canvases in the place of their overlap, wait until the paper is very wet.
Use only a new sharp blade and cut through both layers in one go.

External

External conjugations occur in standard apartments much less internal. Usually it is one - between the hallway and the bathroom, or two of them - even between the bathroom and the kitchen. In apartments with a non-standard layout, there may be more such elements.

Here we work on the same principle: we make a small inversion so that its width at its narrowest point is 1-2 cm. Then we stick a strictly vertical strip on an adjacent wall with an overlap to the width of this inversion. We draw a line under the plumb line and along it we cut the overlap of the canvases, remove the trimmings and carefully glue the edges to the wall.

Important!
Even if it seems to you that your walls are perfectly level, do not try to wrap a whole lane per turn.
This is fraught with folds and creases.
Trimming does not affect the consumption of materials too much, so the cost of repair due to it will not noticeably increase.

Conclusion

To work with the corner zones of the wallpaper should be treated with special attention, because the appearance of your entire interior depends on them. The video in this article and our guide will help you avoid mistakes when working with these elements.

Planned or redecorating in an apartment it is unlikely to do without such a laborious process as decorating the walls with wallpaper. However, today non-woven wallpapers are often used for wall decoration, which have some advantages over their paper counterparts.

For example, such wallpaper options are allowed to be subjected to wet cleaning they do a great job of hiding imperfections. uneven walls and long time retain their attractive design. In addition, non-woven wallpaper is easy to fix on the wall, because it is a very easy-to-use finishing material that does not form vertical, horizontal folds and bubbles. Traditional external and internal corners that are difficult to finish can be decorated with non-woven material without experiencing serious difficulties. To do this, you just need to take into account some of the nuances.

The easiest way to get a beautiful front lawn

Of course, you have seen the perfect lawn in the movies, on the alley, and perhaps on the neighbor's lawn. Those who have ever tried to grow a green area in their area will no doubt say that this is a huge job. The lawn requires careful planting, care, fertilization, watering. However, only inexperienced gardeners think so, professionals have long known about the innovative tool - liquid turf AquaGrazz.

To finish the corners of the room with non-woven wallpaper, do not try to use a single piece of wallpaper in order to decorate both walls that meet in the corner. In this case, the wallpaper will “lead” almost with a guarantee, and the resulting folds will have to be cut, which will negatively affect appearance walls. However, even if this can be avoided, a crooked angle (unfortunately, this is a standard practice for domestic builders) may affect the further design of the apartment with wallpaper. After all, non-woven wallpaper is applied to the walls "butt to joint", respectively, the skew allowed when passing the corner will force all other webs of material to be cut.

Finishing the corners of the room with non-woven wallpaper

The correct wallpapering in the corners with wallpaper made of non-woven cellulose material is as follows:

If everything was done without errors, then the joint between the strips of non-woven wallpaper will be difficult to notice, it will need to be processed with a roller or rags.

outside corner

Features of pasting wallpaper on external corners in the room

External corners in rooms are much less common than internal ones, but they do come across. The technology of applying non-woven wallpaper in this case is almost identical to the passage of internal corners.

At the first stage, we are engaged in geometric surveys:

1. We measure the distance - from the edge of the last pasted strip to the outer corner - and prepare the next strip of wallpaper so that, after fixing it on the wall, it “wraps” around the corner by no more than 50 millimeters.
2. We determine the point of the wrapped strip closest to the corner, it is from it that we will begin to glue a new strip of wallpaper.

Accordingly, measures are taken to apply a vertical strip and remove wallpaper residues.

By the way, if the outer corner is even, as evidenced not only by visual inspection, but also by checking with a plumb line, it is allowed to use one strip of wallpaper. However, it should be borne in mind that possible discrepancies should not exceed 5 millimeters.

paper wallpaper

Paper wallpapers are still popular with finishing works inside the apartment. This is due to their very affordable price and sticker method. It is worth noting that paper wallpaper are not able to hide serious defects in wall surfaces and curved corners. The method of fixing paper wallpaper on the walls is not too different from a similar technology with non-woven wallpaper.

The simplest option involves the sticker of this finishing material "overlap". In other words, the wallpaper panel is glued in the corner with a slight overlap (1-1.5 centimeters) on the adjoining wall, and the next strip is glued directly in the corner itself. This method is distinguished by efficiency, but the visual effect leaves much to be desired.

Paper wallpaper - application features

The second way to glue wallpaper in the corners is suitable even for slightly "littered" walls that form a corner. The initial stage is fully consistent with the previous method, the only difference is that the overlap on the adjacent surface is somewhat larger. The next strip of wallpaper is also glued “overlapped”, but its farthest side from the corner should be oriented along vertical stripe applied with a plumb line. The canvas should lie down with an overlap of 2 centimeters, while having a common border with the adjacent wall. Then, along the applied vertical lines, both layers of the finishing material are cut with a special knife, and after removing its remnants, you can proceed to the further design of the apartment walls. Do not forget to process the cut line with a special roller.

As you can see, the method of gluing paper wallpaper in the corners is very similar to the method of fixing non-woven wallpaper.

Finishing the outer corners with paper wallpaper

External corners meet in the form window slopes, decorative plasterboard partitions, etc. In any case, the geometry of such an angle is extremely important, because such an angle, unlike the internal one, is constantly in sight. That's why possible defects the outer corner should be eliminated in advance and only after that proceed with the wallpaper sticker.

Corner wallpapering technology

The technology of wallpapering on the outer corner is very similar to the second method of fixing wallpaper on inner corner. However, the "overlap" on the adjacent wall should not exceed 5 centimeters, this is due to the fact that a large overlap with uneven wall surface will be difficult to align. Depending on the quality of the wall and wallpaper, wrinkles may appear, they are eliminated with the help of special horizontal cuts on the canvas. The next strip of wallpaper is glued close to the corner, but its far edge must run along a pre-defined vertical strip. Next, using a paint spatula, building level or a metal ruler, we press the center of the overlap and cut off both canvases with a wallpaper knife. After the remnants of the wallpaper are removed, they need to be glued and treated with a roller. The docking joint in this case will be offset by a few millimeters from the corner itself, but this is how it should be. Otherwise, there is a risk of tearing the wallpaper as a result of careless movement.

Little tricks when working with wallpaper

Finishing material is of key importance when working with internal and external corners:

• Paper wallpapers should not be pre-applied with glue, there is a very high chance that they will soak through it and tear in your hands. However, this type of wallpaper does not require trimming when passing corners, because due to the fact that the wallpaper is very thin, it is enough to iron the joints with a dry rag or roller.
• Vinyl wallpapers, on the contrary, are best treated with glue in advance and let them absorb it. Vinyl wallpaper is quite dense material, and with advance prepared canvases will be easier to work with.
• On non-woven wallpaper, you do not need to apply glue, it is applied only to the wall.
• The general rule for all types of wallpaper is that they should be glued in rooms where there are no drafts, air conditioners and heaters do not work.

Do not forget that the walls must be treated with a primer before wallpapering. In addition, the adhesive must match the type of finishing material such as wallpaper. Firms specializing in the production various kinds wallpaper, indicate in the accompanying documents the most suitable adhesive mixtures for their products.

Necessary tools and materials

Tools and materials for wallpapering an apartment

In order for the design of the apartment to be wallpapered quickly and successfully, it is advisable to take care of the availability of the following tools and materials in advance:

• dry rag or sponge to eliminate excess glue;
• building hair dryer;
• brush;
• a vacuum cleaner;
• ladder or scaffolding.

Results

Wallpapers, despite all their shortcomings, as a type of finishing materials used for the interior design of an apartment, are one of the most popular, this is due not only to their price, but also to the fact that they can be pasted without the help of third-party specialists.