The device is receiving and control security and fire. "signal-vk1", "signal-vk1" version 01 addr re

User manual

Fire and security control panels PPKOP 0104059-1-5
"Signal-VK1" and PPKOP 0104059-1-5/01 "Signal-VK1" version 01,(hereinafter - the device), is designed for centralized and autonomous protection of shops, cash desks, banks, pharmacies, institutions and other objects from unauthorized entry and fire by monitoring the status of one alarm loop (AL) with security, fire or security fire detectors and issuing notifications to the centralized monitoring console (CMS) using a relay output about the violation of the alarm loop and the operation of the detectors; on-site control of internal lighting
signaling devices, external sound and light annunciators; control of the arming/removal of the device using the built-in magnetically controlled contact; supplying detectors with output "+12 V"; control of the opening of the body of the Signal-VK1 device using a switch; providing change of parameters of work by means of removable crosspieces.
1.1.2 The Signal-VK1 device is intended for installation inside a guarded facility and is designed for round-the-clock operation.
1.1.3 The Signal-VK1 device is designed for joint operation with centralized monitoring consoles "Neva-10", "Neva-10M", "Tsentr-M", "Tsentr-KM", "Progress-TS", "Phobos", AWP "Phobos", etc.

In the AL of the Signal-VK1 device, the following can be included:

- magnetic contact signaling devices IO102-2, IO102-4, IO102-5, IO102-6, "Foil", "Wire" sensors;
- shock-contact detectors "Window-6";
- detectors of optical-electronic, ultrasonic and radio wave types "Photon-6", "Photon-6A", "Photon-6B", "Photon-9", "Photon-Sh", "Photon-SK", "Photon-SK2" ", "Astra-MS", "Argus-2", "Argus-3", "Echo-3", "Showcase", "Echo-3", "Echo-A" and the like;
- detectors of acoustic type "Harp", "Glass-1", "Glass-2-1", "Glass-3";
- detectors of capacitive type "Peak";
- detectors security combined "Falcon-2";
- detectors of piezoelectric type "Gran-2", "Shoroh-1-1";
- output circuits reception and control devices;
- thermal fire detectors "IP 101-2", "IP 103-5", "IP103-7", etc.
1.1.4 Device Signal-VK1 has the possibility of autonomous protection when powered from the AC mains, and in the absence of a network from a backup power source or built-in battery with the issuance of signals to remote light and sound annunciators and a built-in indicator.
1.1.5 Transmission of notifications to the monitoring station about an alarm or fire is carried out using relay contacts. Fault reporting is carried out using the "open collector" (OK) output.
1.1.6 The device is powered from the AC mains with voltage (220+22-33) V, frequency (50±1) Hz and from the built-in rechargeable battery with a nominal voltage of 12 V and a capacity of 1.2 A/h or an external backup source direct current voltage (12 +2.2-0.6) V.
1.1.7 The Signal-VK1 device provides the possibility of power supply at the guarded facility to detectors that require a separate 12 V power supply.
1.1.8 The device is intended for installation inside a guarded facility and is designed for round-the-clock operation.
1.1.9 The design of the device does not provide for its use in conditions of exposure to aggressive media, dust, as well as in fire hazardous rooms.
1.1.10 According to the type of maintenance, the device belongs to products with periodic maintenance. The average total operational duration of maintenance is not more than 0.15 hours per month.
1.1.11 The device is intended for operation under the following conditions:
- Operating temperature range environment– from 243 to 323 K (from minus 30 to +50 °C) (without battery) and from 263 to 323 K (from minus 10 to +50 °C) with battery.
- relative humidity at an ambient temperature of 298 K (+25 °С) - up to 98%;
- vibration loads in the range from 1 to 35 Hz with a maximum acceleration of 0.5 g.
1.1.12 In terms of environmental protection, the device has
ordinary execution according to OST 25 1099-83.
1.1.13 The device belongs to single-functional, recoverable, repairable and serviceable products of group II type 1 according to GOST 27.003-90.
1.1.14 The law of distribution of uptime is exponential.
1.1.15 An example of recording the device designation when ordering it and in the documentation of other products is given in Table 1.......

Intended use
2.1 Preparing the Signal-VK1 device for use
Precautions for Preparing the Instrument
When operating the device, the current "Rules for the technical operation of consumer electrical installations" and "Safety regulations for the operation of consumer electrical installations" must be observed.
The sources of danger in the device are:
- contacts ХТ1:1 and ХТ1:3 for connecting the AC mains. Mounting, installation, maintenance should be carried out when disconnected from
device mains voltage. It is forbidden to use fuses that do not correspond to the nominal value. Installation and maintenance of the device must be carried out by persons with a safety qualification group of at least the third.

transcript

1 Fire and security control panel PPKOP /02 "Signal-VK" version. 02 ADDR RE Operating manual CONTENTS Introduction 1 1 Description and operation of the product Purpose of the product Characteristics Composition of the product Design and operation of the product 7 2 Intended use Preparing the product for use Using the product 11 3 Checking the technical condition of the device 11 4 Maintenance 14 5 Maintenance 15 Appendix A Overall and mounting dimensions of the device 16 Appendix B Electrical diagram of the functional device 17 Appendix C Electrical connection diagram of the device 18 Appendix D General check of the device 19 Appendix E Timing test device AL 20 operation and operation of the control panel, security and fire PPKOP /02 "Signal-VK" version Description and operation of the product 1.1 Purpose of the product Control panel, security and fire PPKOP /02 "Signal-VK" version. 02 (hereinafter - the device) is designed for centralized and autonomous protection of shops, cash desks, banks, pharmacies, institutions and other objects from unauthorized entry and fires by monitoring the state of the alarm loop (AL) with security, fire or security fire detectors included in it and issuing notifications to the centralized monitoring console (CMS) about the violation of the alarm loop, as well as managing external sound and light annunciators at the facility. The device is designed for joint operation with centralized monitoring consoles such as "Siren-2M", "Neva-10", "Neva-10M", "Tsentr-M", "Tsentr-KM", "Progress-TS", "Phobos" and etc. The alarm loop of the device can include: - magnetic contact signaling devices IO102-2, "SMK-1", "SMK-2", "SMK-3"; - sensors like "Foil", "Wire"; - shock-contact detectors of the "DIMK", "Window-4", "Window-5", "Window-6" types; one

2 - detectors of optoelectronic, ultrasonic and radio wave types 9981, "Photon-5", "Photon-6", "Photon-8", "Photon-SK", "Vector-2", "Vector-3", " Echo-2", "Wave-5" and the like; - output circuits of receiving and control devices; - thermal fire detectors "IP-104-1", "IP103-4/1" ("MAK-1"); - magnetic contact fire detectors "IP-105-2/1"; - fire detectors flue type"IP-212-5" ("DIP-3"), "IP" ("DIP-6"), "IP U" ("DIP-U"), "IP" ("DIP-34"), " IP-212-3SU" ("DIP-3SU") The device has the possibility of autonomous protection when powered from the AC mains with the output of signals to remote light network, light and sound direct current annunciators, a built-in light indicator that displays the state of the loop. At the same time, it is possible to set a delay for turning on the sound annunciator in case of violation of the AL protected object of detectors such as "Photon", "Echo", "Wave", "Peak", "Vector" and the like. of the built-in indicator and in the mode of switched off annunciators and the built-in indicator using a remote control via a radio channel at a distance of up to 30 m The device is designed for installation inside a protected facility and is designed for round-the-clock operation. fire hazardous premises By type of technology Maintenance The instrument is classified as a product with periodic maintenance. The average total operational duration of maintenance is not more than 0.15 hours per month. The device is designed for operation under the following conditions: 1) ambient operating temperature range - from 243 to 323 K (from minus 30 to +50 ° C); 2) relative humidity at an ambient temperature of 298 K (+25 0 C) - up to 98%; 3) vibration loads in the range from 1 to 35 Hz with a maximum acceleration of 0.5 g (4.9 m/s 2). 1.2 Characteristics Power supply of the device is carried out from the alternating current network with a frequency of (50±1) Hz, () V. 2

3 1.2.2 Supply voltage from a redundant DC source - (12.0 ± 1.8) V Power consumed by the device from the AC mains without a network siren in standby mode and in the "Alarm" mode must be no more than 12 V A The current consumed by the device from a backup source, taking into account the power supply of active detectors in standby mode and alarm mode - no more than 140 mA Number of alarm loops connected to the device (information capacity) - one "Alarm loop on the monitoring station "Alarm" Loop on the monitoring station "Normal" in the loop (to the built-in indicator) "Alarm" in the loop (to the built-in indicator) "Normal" to remote mains and DC light annunciators "Alarm" to remote mains and DC light annunciators "Alarm" on remote mains and direct current sound annunciators The device provides switching of remote light and sound annunciators in accordance with Table 2. Table 2 power Remote light direct current 12 V, 50 mA Remote sound DC 12 V, 0.3 A Remote light mains up to 60 W Remote sound mains up to 60 W The device is in standby mode with the resistance of the loop, taking into account the resistance callout, from 2 to 11 room. The device remains in standby mode when the loop is violated for 50 ms or less The device switches to the "Alarm" mode when the loop resistance is less than 2 kΩ or more than 11 kΩ for 70 ms or more or pressing button "2" of the remote control Device operation The device ensures operability in seven modes of operation: - power-on mode; - transition to standby mode; - standby mode; - "Alarm" mode; - mode of switched off annunciators and indicators; - programming mode; - erasing keyfob codes from memory. Power-on mode The device after switching on the supply voltage for 2 minutes does not remember the violation of the loop and provides the following operating procedure: 1) in the normal state of the loop: 3

4 - built-in indicator (red color) and remote light annunciators glow with continuous light; - remote sound annunciators are switched off; - output contacts of the monitoring station relay are closed; 2) in case of violation of the alarm loop according to clause 1.2.9: - remote light annunciators and the built-in indicator (red color) glow with intermittent light with a frequency of 1 Hz; - the output contacts of the monitoring station relay are open for the duration of the alarm loop violation according to clause 1.2.9; - remote sound annunciators are switched off; 3) when the alarm loop is restored to its normal state according to clause 1.2.8: - the built-in indicator of the device (red color) and remote light annunciators glow with continuous light; - remote sound annunciators are switched off; - ARC relay contacts are closed; 4) at the end of 2 minutes, the device switches to standby mode, the indicator and light annunciators turn off for 1 s, and the sound annunciators turn on for 0.05 s Switching to standby mode device, sound annunciators are switched on for 0.05 s and it should not remember the violation of the loop within 2 minutes and should provide the following operation procedure: 1) in the normal state of the loop according to clause 1.2.8: - built-in indicator (red) and light annunciators glow with a continuous light; - remote sound annunciators are switched off; - output contacts of the monitoring station relay are closed; 2) in case of violation of the alarm loop according to clause 1.2.9: - remote light annunciators and the built-in indicator (red color) glow with intermittent light with a frequency of 1 Hz; - the output contacts of the monitoring station relay are open for the duration of the alarm loop violation according to clause 1.2.9; - remote sound annunciators are switched off; 3) when the alarm loop is restored to its normal state according to clause 1.2.8: - the built-in indicator of the device (red color) and remote light annunciators glow with continuous light; - remote sound annunciators are switched off; - ARC relay contacts are closed; 4) at the end of 2 minutes, the device switches to the standby mode of operation, the indicator and light annunciators turn off for 1 s, and the sound annunciators turn on for 0.05 s.

5 - continuous glow of the built-in indicator of the device (red color) and remote light annunciators; - off state of remote sound annunciators; - closed state of the output contacts of the monitoring station "Alarm" mode The device switches from standby mode to the "Alarm" mode when the alarm loop is violated by p or when button "2" of the remote control is pressed, while it provides: 1) intermittent switching on of the built-in indicator (red color) and remote light annunciators with a switching frequency of 1 Hz; 2) turning on remote sound annunciators immediately for 2 minutes at installed jumper"XT3" or after 30 s with the "XT3" jumper removed, after breaking the alarm loop or pressing the button "2" of the key fob; 3) permanent open state of the CMS relay contacts. Restoring the alarm loop to the normal state should not lead to a change in the "Alarm" mode until the device is powered off or the button "1" of the key fob is briefly pressed. power supply or switching to standby mode after a short press of the key fob button "1". At the same time, it provides: 1) the off state of the built-in indicator of the device and remote light annunciators; 2) off state of remote sound annunciators; 3) the closed state of the output contacts of the monitoring station relay in the normal state of the alarm loop on n and the button "2" of the key fob is not pressed and their open state, for a period of at least 2 s, when the alarm loop is violated on p or for the time the button "2" of the key fob is pressed. The transition to the standby mode according to p should be carried out by briefly pressing the button "1" of the key fob. Programming mode Switch the device to the mode of turned off sirens by pressing the button "1" of the key fob. When the built-in PROG button is pressed, the built-in indicator should glow green light 0.5 s and the remote control programming mode starts. Without releasing the PROG button, press buttons 1 or 2 on the master key fob from the accessory kit. The indicator flashes green twice. After that, pressing buttons 1 or 2 on the programmable key fob enters its code into the device's memory, while the indicator glows green for 0.5 s. If this key fob code is already memorized, the indicator flashes green three times. If 40 keyfobs have already been programmed (excluding the master keyfob), then when trying to program 41 keyfobs, the indicator glows green for 1.5 s. When the PROG button is released, the indicator glows green for 1 s and the alarms and indicators are switched off again. Mode for erasing keyfob codes from memory 5

6 To switch to this mode, you must turn on the power of the device while pressing the PROG button. After four initial flashes, the indicator glows green for 0.5 s. Without releasing the PROG button, press buttons 1, 1, 2, 2 on the master key fob, while the indicator glows green for 0.5 s after each press. If the code is entered correctly, then the indicator glows green for 1 s and the memory is cleared, otherwise, the indicator is off. If the code is entered incorrectly, it is necessary to repeat the switching on with the PROG button pressed. In this mode, the master key fob code is not erased. After releasing the PROG button, the transition to standby mode begins according to p. The device provides power to active detectors with the following parameters: - supply voltage (12 +1.8-1.2) V; - consumed current - no more than 40 mA. The ripple voltage in the channel is 12 V (peak value) - no more than 15 mV The device remains operational after a short circuit in the power supply circuit of active detectors. Maximum amount not less than 20 detectors connected to the alarm loop The device provides power supply to fire detectors of the "DIP" type through the alarm loop. The maximum number of connected detectors should be no more than: "DIP-3" - 3 pcs., "DIP-6" - 8 pcs., "DIP-U" 20 pcs., "DIP-34" 20 pcs., "DIP- 3SU" 20 pcs. The device switches from the standby mode to the "Alarm" mode when the detectors ("Window", "DIP", "Wave-5", "Photon-8") are triggered, fed by the AL The device provides current limitation at a level not more than 20 mA, flowing through the triggered detector, powered by the AL The device provides voltage from 21 to 24 V at the AL input, in the standby mode of operation. In the alarm mode, the voltage at the AL input is not more than 27 V not less than 80 V, switching current not less than 50 mA The contacts of the control relay of the CMS device open when there is no supply voltage (and there is no backup source) sinusoidal waveform with a frequency of 50 Hz effective high voltage value up to 1 V, as well as impulse pickups in the form of single voltage pulses with an amplitude of up to 300 V, a duration of up to 10 ms in accordance with GOST R Industrial radio interference created by the device during operation does not exceed the values ​​specified in GOST R Weight of the device - no more than 2 kg Overall dimensions of the device - no more than 157x151x71 mm. 6

7 Content of precious materials: - gold - 0.028 g, - silver - 0.054 g. symbol Qty. АЦДР Fire and security control panel 1 PPKOP / 02 "Signal-VK" version. 02 Set of spare parts: Resistor OZHO TU S2-33N-0.5-8.2 kΩ +5% 1 ATSDR RE Fusible inserts OYu TU VPT6-10 (2 A) VPT6-5 (0.5 A) 2 2 Remote controls 2 Fire and security control panel PPKOP /02 "Signal-VK" isp. 02 Operation manual ATSDR Set of SPTA group for 12 devices 1 ATSDR ZI List of spare parts for the "Signal-VK" device vers Design and operation of the device The device is structurally made in the form of a plastic case, consisting of a base and a cover. Appearance of the device and its overall dimensions are given in Appendix A. A printed circuit board is installed inside the case on the base, on which all the main elements and components of the device are mounted. On the reverse side of the base there are two shaped holes, with the help of which the device is fixed on the wall in the working position. - voltage stabilizers 12 V and 5 V; - voltage converter from 12 V to 24 V; - reference voltage divider; - single-chip microcontroller; - receiver module; - AL state control unit; - node of sound annunciators; - assembly of light annunciators and annunciator; - signal relay unit; - body opening control unit; - remote control programming unit; - unit for delaying activation of sound annunciators. The input block and the rectifier contain fusible links, a step-down mains transformer with a thermal fuse, a rectifier and a smoothing filter. The central node for processing, storing and controlling is made on a single-chip microcontroller, providing: 7

8 1) input analog signal through three channels from the AL status control unit and from two points of the reference voltage divider that set the operation thresholds, and their comparison; 2) input and processing of digital signals from the key fob programming unit (S1), the case opening control unit (S2), the unit for delaying the activation of sound annunciators (XS1 jumper); 3) receiving and processing parcels from the remote control using the receiver module, registering their individual numbers; 4) output of control signals by the built-in indicator of the device, control panel relay of the monitoring station, remote light and sound annunciators; 5) formation of signals for the operation of the voltage converter from 12 V to 24 V. The setting of 30 s for the delay in turning on the sounders is carried out by the XS1 jumper. The presence of the XS1 jumper in the XT3 pin connector means that the sounder is turned on without delay; the absence of the XS1 jumper leads to a delay in turning on the sounders by 30 s. The receiver module contains an antenna and a receiver, from the output of which the signal goes directly to the input of the microcontroller. The unit is powered by a 5 V stabilizer. When the key fob button is pressed, the receiver module receives a code message and transmits it in a serial code to the microcontroller input. The AL status control unit supplies 24 V voltage through a limiting resistor to the alarm loop and supplies voltage from the loop through a matching circuit to the analog input of the microcontroller. The unit of light annunciators, signaling device and indicator is controlled directly from the outputs of the microcontroller and includes an LED indicator with a controlled glowing light, a key amplifier that controls a direct current light annunciator, and a relay through the contacts of which the light network annunciator is connected. The sound annunciator unit includes a key transistor that controls a direct current sound annunciator, protective diodes and a relay controlled by the microcontroller output, through the contacts of which the network sound annunciator is connected. The alarm relay assembly contains a reed relay with protective diodes controlled by the microcontroller output. The housing opening control unit contains a microswitch (S2), the signal from which enters the microcontroller and in case of opening the housing, the device switches to the "Alarm" state. 2 Intended use 2.1 Preparing the device for use Safety precautions when preparing the device: a) When using the device, observe the current "Rules for the technical operation of consumer electrical installations" and "Safety regulations for the operation of consumer electrical installations". b) The sources of danger in the device are: 1) contacts "~220 V" for connecting the AC mains; 2) contacts ХТ1:1 - ХТ1:4 for connecting remote sound and light annunciators; 3) fuse holders on the input unit (F1, F2); 4) contacts of the input winding of the power transformer (T1). eight

9 c) Installation, installation, maintenance should be carried out with the mains voltage disconnected from the device. d) Electric wires must be protected from possible violation insulation in places around metal edges. e) It is forbidden to use fuses that do not correspond to the nominal value. f) Installation and maintenance of the device must be carried out by persons with a safety qualification group of at least the third. Installation procedure a) The device is installed on walls or other structures of a protected room in places protected from atmospheric precipitation, mechanical damage and access by unauthorized persons. b) Light annunciators must be placed in places that are well visible to the management of the facility after leaving the premises. c) Installation of the device, light and sound annunciators is carried out in accordance with the RD "Rules for the production and acceptance of work. Installations of security, fire and security and fire alarm". d) Install the device in the following sequence: 1) determine the installation location of the device; 2) mark the fastening in accordance with Appendix A, mount the fastening elements; 3) install the device on the fastening elements. e) Mount the alarm loop and connecting lines in accordance with scheme electrical connections given in Appendix B. f) Connect the connecting lines to the terminals of the device in the following sequence: 1) connect the wires of the network light annunciator to contacts 3 and 4 of XT1 and the DC light annunciator to contacts 11, 12 of XT2 (see Appendix B); 2) connect the wires of the network sounder to pins 1 and 2 of XT1, and the wires of the DC sounder to pins 1 and 2 of XT2, observing the polarity; 3) connect the AL wires to pins 7 and 8 of XT2; 4) connect the power supply circuits of the detectors to contacts 3 and 4 of XT2, observing the polarity; 5) connect the remote control lines to pins 5 and 6 of XT2; 6) connect a backup DC source to pins 9 and 10 of XT2, taking into account the polarity; 7) connect to pins 5 and 6 of XT1 the AC mains wires; 8) AC mains supply and standby DC supply must be connected to the instrument through switches that are used to turn off the instrument. The backup power supply switch S2 must be installed in the circuit: positive output of the power supply - terminal XT2:10. The negative output of the power supply must be connected to terminal XT2:9. Switch S1 must be installed in the circuit: phase output of the network - terminal ХТ1:6. When turning off the device, both power supplies must be turned off. Failure to turn off the standby DC power supply will cause it to discharge. Getting Started 9

10 Check the correctness of the performed installation and check the operability of the device when powered from the AC mains The device provides operability in seven modes of operation in accordance with paragraph of this document To check the operability of the device, it is necessary: P.; 2) check the operation of the device during the initial switching on. Apply mains voltage to the device. Within 1 min after turning on the power, simulate the violation and restoration of the alarm loop, including by pressing and releasing the button "2" of the remote control. If the loop and the device are in good condition, the light annunciators and the built-in indicator should glow with a steady light, if the loop is violated, with intermittent light. Sounders must be turned off. Switch the device to the mode of switched off alarms and the indicator of the device by briefly (lasting at least 1 s) pressing the button "1" of the key fob; 3) set the delay from the moment of alarm loop violation until the sounder is turned on (remove the XS1 jumper from the XT3 pin connector); 4) check the operation of the device in the mode of disabled annunciators, standby mode and alarm mode. Violate the loop - open front door and leave it open. Apply voltage to the device from the mains and briefly press the button "1" of the key fob. Light and sound annunciators and the built-in indicator of the device must be turned off. Briefly press button "2" on the remote control. Light annunciators and the indicator of the device should glow with intermittent light. Sounders should not work. Close the front door, while the glow mode of the light annunciator and the built-in indicator should become continuous. After 2.5 minutes, open the front door. The light annunciators and the built-in indicator should switch to a flashing alarm glow mode and after a delay of 30 s, the sound annunciators will turn on for 2 minutes. Close the front door. The nature of the operation of the annunciators should not change. Briefly press button "1" on the key fob. Light and sound annunciators and the indicator of the device should turn off; 5) check the operation of the device in the remote control programming mode. Switch the device to the sirens off mode by briefly pressing button "1" on the key fob. Remote light annunciators and the built-in indicator of the device should turn off. If the indicator light was not lit, then the key fob button should not be pressed (otherwise the device will go into standby mode, as evidenced by the inclusion of the indicator light). Open the case of the device, press the S1 button installed on the device board. The built-in indicator of the device will light up green continuous light. Remote light annunciators do not light up. Without releasing the S1 button, press any of the remote control buttons for a few seconds. Successful writing to the device memory (registration) of the individual key fob number will be confirmed by a short-term turning off of the built-in indicator. Release button S1, close the lid of the device. Check the ability of the device to accept the commands of the registered key fob according to p by converting to various modes(short-term pressing of button "1" switches the device to the mode of off alarms and back to standby mode; short-term pressing of button "2" switches the device to alarm mode) Check the ability of the device to record the operation of each detector included in the loop observations in the following sequence: 1) switch the device to standby mode and inform the operator at the monitoring station to 10

11 objects were taken under protection; 2) switch the device to alarm mode. The operator of the monitoring station must determine the violation of the alarm loop. Check the operability of the device according to p when powered from a backup power source Remove the mains and backup voltage from the device. 2.2 Use of the product Arm the facility in the following sequence: 1) close all windows, vents, doors, etc., on which electrical contact detectors are installed, open the exit door; 2) briefly press button "1" of the key fob no further than 30 m from the device. In this case, the light annunciators and the built-in indicator must be turned off, the sound annunciators must not work; 3) inform the duty officer of the monitoring station by phone of the conditional number of the object to be guarded, put the handset on the device; 4) exit the protected premises, close the entrance door and briefly press the button "1" of the key fob, while the light annunciators should glow with a steady light, indicating that the object is armed, and the alarm loop is restored Disarm the object when the premises are opened in the following order: 1) open the front door, while the light annunciators should switch to a flashing mode of operation; 2) approach the device at a distance of no more than 30 m and briefly press the button "1" of the key fob, while the device will switch to the mode of turned off annunciators; 3) call the monitoring station by subscriber phone and inform the operator about the disarming of the object. It must be borne in mind that if the time from the moment the door is opened to pressing the button "1" of the key fob exceeds set time delay, the buzzer will sound. 3 Checking the technical condition of the device 3.1 Checking the performance of the product technical means security and fire alarm systems (TS FSO), which check the technical condition (incoming control), and includes a check of the device's performance in order to identify defects and assess their technical condition. Non-compliance of devices with the requirements specified in this methodology is the basis for making claims to the manufacturer and calling his representative to continue the test and resolve the issue of eliminating defects. Checking the technical condition of devices is organized by laboratories and repair shops of security units and is carried out by maintenance personnel who have studied the principle of operation of the device. and this methodology and having a qualification of at least 3 categories of electricians of the OPS. The check is carried out under normal climatic conditions according to GOST: 1) ambient temperature - () 0 С; eleven

12 2) relative air humidity - (45-80)%; 3) atmospheric pressure mm Hg. (84-106.7) kPa The check is carried out according to the scheme of the general check of the device, which is given in Appendix D. The total time for checking the technical condition of one device is no more than 40 minutes. Notes 1 Connection and disconnection of wires during checks should be carried out with the instrument and stand turned off. 2 All checks should be carried out taking into account the technical readiness time of the device, which is equal to 3 s. Check the device in the following sequence: a) check the condition of the package and unpack the device; b) check the scope of delivery in accordance with the operation manual of the ADDR RE, the presence and composition of spare parts and accessories; c) make sure that there is no mechanical damage to the instrument case; d) by shaking the device, make sure that there are no foreign objects inside it; e) check fastening of terminal blocks; f) check the presence, compliance with the rating and serviceability of the device fuses; g) check the compliance of the device number and the date of issue indicated in the instruction manual. Control of the main specifications the device to be carried out according to the general check scheme (Appendix D) Set the switches S1, S5 on the stand to the off position. Connect the stand to AC mains. Turn on the NETWORK switch of the stand and set the device supply voltage (220 ± 5) V using the TV1 variator, controlling it using the PV3 voltmeter. Turn off the NETWORK switch. Turn on the DC source G1 and set its output voltage (12.0 ± 0.5) V, controlling it with the voltmeter PV1. Note - In all modes, pressing button "1" of the key fob is accompanied by a short, for a time of 0.05 seconds, turning on sound annunciators Turn on the NETWORK switch of the general test stand. The built-in indicator of the device, the indicators of the CMS stand, LAMP, INDICATOR should glow with a steady light, the CALL, SIREN indicators should not glow. After a time, at least 2 minutes after turning on the POWER switch, press briefly (at least 0.5 s) button "2" of the remote control. When the device is working correctly, the indicator of the CMS stand should turn off, the indicators LAMP, INDICATOR and the built-in indicator of the device should glow with intermittent light, the indicators RING, SIREN should turn on. Press briefly (at least 1 s) button "1" of the remote control. When the device is working correctly, the indicator of the monitoring station stand should turn on, and the indicators LAMP, INDICATOR, BELL, SIREN and the built-in indicator of the device should turn off. Press and hold button "2" on the key fob. When the device is working correctly, the indicator of the monitoring station stand should turn off, and when the button "2" is released, it should turn on. Press briefly (at least 1 s) button "1" of the remote control. The built-in indicator of the device, the indicators of the CMS stand, LAMP, INDICATOR should glow with a steady light, the CALL, SIREN indicators should not glow. Press and release button 12

13 "2" keychains. For the time the button is pressed, the CMS indicator should turn off, and the LAMP, INDICATOR and built-in indicator of the device should glow with intermittent light. After a period of at least 2 min. after pressing the button "1" of the key fob, briefly press the START button of the short-term signal generator, and after a time of no more than 2 s - the button "1" of the key fob. First, the built-in indicator of the device and indicators LAMP, INDICATOR should glow with intermittent light, the indicator of the monitoring station should turn off, and after pressing button "1" of the key fob, the built-in indicator of the device and the indicators LAMP, INDICATOR should turn off, the indicator of the monitoring station should turn on. Stand indicators CALL, SIRENA should not turn on. Turn off the POWER switch of the stand Turn on the POWER switch of the stand and at the same time start the stopwatch. The built-in indicator of the device, indicators of the monitoring station stand, LAMP, INDICATOR should be lit, indicators RING, SIREN should not be lit. Every 10 s, briefly press the OPEN switch of the stand. Fix the time until the permanent turning off of the CMS indicator and turning on the indicators CALL, SIREN of the stand, which should be at least 2 minutes. Measure, using a stopwatch, the time of turning on the indicators CALL, SIREN, which should be at least 2 minutes. Using a stopwatch, measure the frequency of blinking of the built-in indicator of the device and indicators LAMP, INDICATOR of the stand. The frequency is determined as the quotient of the number of flashes divided by the selected time (10 s). When the device is working properly, the flashing frequency is 1 Hz. Turn off the POWER switch of the stand Press the OPEN switch and turn on the POWER switch of the stand. Indicators of the stand CMS, BELL, SIREN should not glow, indicators LAMP, INDICATOR and the built-in indicator of the device should glow with intermittent light. Using voltmeters PV4 and PV2, measure the voltage in the alarm loop and the power supply circuit of the detectors, which, respectively, should be (24 ± 2) V and (12 + 1.2-1.8) V. After a time, no more than 1 minute after switching on switch NETWORK, press the switch OPEN of the stand. When the device is working correctly, the indicators of the CMS stand, LAMP, INDICATOR, the built-in indicator of the device should glow with a steady light, the CALL, SIREN indicators should not glow. Use voltmeters PV4 and PV2 to measure the voltage in the alarm loop and the power supply circuit of the detectors, which, respectively, should be (21-24) V and (12 +1.2-1.8) V. Press the switch CLOSE of the stand. If the device is working correctly, after a time of no more than 2 s, the indicators of the CALL, SIREN stand should turn on (glow with a steady light) for a period of 2 minutes, the CMS indicator should turn off, the LAMP, INDICATOR indicators and the built-in indicator of the device should glow with intermittent light. Press the switch MEASUREMENT I of the stand. Using a PA2 milliammeter, measure the current in the loop, which should be no more than 20 mA, and using a PV2 voltmeter, measure the voltage in the detector power supply circuit, which should be (12 + 1.2-1.8) V. Press the MOD.I and CLOSE switches stand. The mode of operation of the indicators of the CMS stand, LAMP, INDICATOR, BELL, SIREN and the built-in indicator of the device should not be changed. Turn off the switch NETWORK of the stand. 13

14 Connect the circuit between the milliammeter PA2 and the XT2:8 contact of the device to the output contacts of the relay "Device for checking the time parameters of the AL" (UP), the diagram of which is given in Appendix E. Connect the power supply circuits of the device to the direct current source G1 of the general test bench. Using the potentiometer R3 UP (see Appendix D), set the AL break time to 50 ms, controlling it with a frequency meter (the error in setting the break time is no more than 2%). Turn on the NETWORK switch of the stand. The indicators of the CMS stand, LAMP, INDICATOR and the built-in indicator of the device should glow with a steady light, the indicators of the CALL, SIREN stand should not glow. After a time of at least 2.5 minutes after turning on the POWER switch, press the S1 UP button. The device should remain in the standby mode of operation, the nature of the indication should not change. Turn off the switch NETWORK of the stand. Using the potentiometer R3 UP, set the AL break time to 70 ms (setting error is not more than 2%). Check the absence of a jumper (jumper) in the pin connector located on the device board. Turn on the switch NETWORK of the stand and after a time of at least 2.5 minutes press the button S1 UP. The device should switch to the alarm mode of operation, the built-in indicator and indicators of the stand LAMP, INDICATOR should glow with intermittent light. After a time of at least 30 s after pressing the button S1 UE, the indicators of the stand CALL, SIREN should turn on for 2 minutes. Turn off the NETWORK switch of the stand Turn off the LAMP, INDICATOR, BELL, SIREN indicators from the stand and turn on the NETWORK switch. Measure the current consumed by the device with a RA3 milliammeter, which should be no more than 55 mA. Turn on the RESERVE switch of the stand and turn off the switch of the stand NETWORK. The device must remain in the standby mode of operation - the indicator of the monitoring station must be lit. Measure the current consumed by the device with a PA1 milliammeter, which should be no more than 100 mA. Using voltmeters PV4 and PV2, measure the voltage in the alarm loop and the power supply circuit of the detectors, which, respectively, should be (18 24) V and (12 + 1.2-1.8) V Make an entry in the repair log and input control means of the OPS on the results of the check. 4 Maintenance 4.1 The list of instrumentation required for maintenance and repair in a workshop is given in Table 4, the approximate consumption of components and materials necessary for maintenance and repair of the device is in Table 5. The list of the most common or possible malfunctions and methods their elimination are given in table 6. 14

15 Table 6 Fault name, outward manifestation and additional features Probable Cause Remedy 1 When the mains source is turned on, the light alarms do not light up 2 When the mains source is turned on, the fuse fails 3 In the alarm notification mode, the sounder does not turn on and / or the alarm signal is not generated on the monitoring station 4 When buttons "1" and "2" are pressed keyfobs do not switch to standby mode, sirens off mode, alarm mode No voltage in the network Faulty mains fuses in the device Faulty signal lamp Faulty transistor VT1 Short circuit in the secondary or primary circuits of transformer T1, breakdown of bridge diodes VD7 VD10, breakdown of capacitor C5 Faulty call. Faulty transistor VT3. Relays K3, K2 are faulty The battery in the key fob is faulty Inconsistency between the code messages of the key fob and the codes stored in the memory of the device's microcontroller Check the presence of voltage in the network Replace the fuses Replace the signal lamp Replace the transistor VT1 Check the serviceability of the transformer T1, diode bridge VD7 VD10, capacitor C5. Replace defective elements Replace defective elements Replace the battery in the key fob Register the key fob according to p. When performing repair operations, it is necessary to comply with the requirements for the protection of integrated circuits from static electricity in accordance with OST Dangerous value of the electric potential +100 V. separate agreement. 5 Maintenance 5.1 Maintenance of the device is carried out according to a preventive and preventive system, which provides for annual maintenance. 5.2 Annual work maintenance performed by employees of the service organization and include: 1) checking external state device; 2) performance check in accordance with paragraphs of this manual; 3) checking the strength of the fastening of the device, light and sound annunciators, the condition of external installation wires, installation connections; 4) checking the AL parameters; 5) checking the operating time of sound annunciators and the frequency of switching light annunciators. fifteen

16 APPENDIX A (mandatory) Overall and mounting dimensions

17 APPENDIX B FUNCTIONAL DIAGRAM OF THE INSTRUMENT PTSN Power supply loop Reference voltage divider Signal relay unit Status control unit AL AL ​​Status indicator Unit for delay activation of sound alarms XT3 Key fob programming unit Single-chip microcontroller Unit of light alarms, annunciator and indicator Remote light annunciator Remote light alarm S1 Control unit case opening Sounder unit Remote sounder Siren S2 Receiver module Power supply AL ~220 V ~20 V Stabilizer 24 V Converter Input unit Voltage rectifier 12 V voltage stabilizer 5 V 5 V 17

18 APPENDIX C ELECTRICAL CONNECTION DIAGRAM OF THE INSTRUMENT CONTROL PANEL "Signal-VK" isp. 02 XT1 Cont. Circuit Mains ~220 V Bell Lamp 6 Mains ~220 V 5 Mains ~220 V 4 Lamp 3 Lamp 2 Bell 1 Bell ХТ2 Circuit 12 Indicator + 11 Indicator - 10 Reserve +12 V 9 Reserve 12 V 8 Loop + 7 Loop - 6 Remote 5 Remote V (12 V, 40 mA) 3 0 V 2 Siren + Siren (12 V, 300 ma) 1 Siren - R - resistor S2-33-N-0.5-8.2 kΩ ± 5%; I1 - detector with normally closed contacts; I2 - a detector with normally open contacts or a detector of the type "Window", "DIP", "Wave-5", "Photon-8" 18

19 APPENDIX D Scheme of the general check of the device HL4 "LAMP" HL2 "CALL" PPKOP "Signal VK" isp. 02 ХТ2 Circuit 6 Mains ~220V 5 Mains ~220V 4 Lamp 3 Lamp 2 Bell 1 Bell Cont. R3 "INDICATOR" R6 R4 R7 R5 R10 ХТ1 Cont. Circuit 12 Indicator + 11 Indicator - 10 Reserve +12 V 9 Reserve -12V 8 Loop + 7 Loop - 6 Remote control 5 Remote control V 3 0 V 2 Siren + 1 Siren - R8 R9 F1 - fusible insert VP1-1 1 A 250 V; HL1,HL3,HL5 - single indicator AL307 BM; HL2, HL4 - incandescent lamp B; R1 - resistor С2-33Н-0, Ohm ± 5%; R2 - resistor S2-33N-0.25-8.2 kΩ ± 5%; R3 - resistor S2-33N-0.5-2 kΩ ± 5%; R4 - resistor С2-33Н-0, Ohm ± 5%; R5, R6 - resistor S2-33N-0.5-2 kΩ ± 5%; R7 - resistor С2-33Н-0, Ohm ± 5%; R8 - resistor С2-33Н Ohm ± 5%; R9 - PEV-7.5-39 Ohm resistor ± 5%; R10 - resistor S2-33N Ohm ± 5%; S1...S5 - switch PKn61 N; TV1 - single-phase variator RNO-250-2; VD1 - zener diode KS168A; G1 - direct current source B5-30; PV1...PV4 - voltmeter V7-22; RA1 ... RA3 - combined instrument C Note - Instead of the indicated instruments, similar ones in terms of characteristics and accuracy class can be used

20 APPENDIX D Device for checking timing parameters AL + (24 ± 3) V HL1 To the frequency meter Capacitors C1- K V-0.1 mf ± 10% C2 - K V-3.3 mf ± 10% C3 - K pf ± 10% S4 - K V-470mf-V Single indicator HL1 - AL307BM Relay K1 - relay RES-82 RS4.569 Resistors R1, R2 - S2-33N-0.25-1 kom ± 10% R3 - SP4-1a-15 kom R4 - С2-33Н-0, com±10% R5 R7 - С2-33Н-0.25-10 com±10% R8, R9 - С2-33Н-0.25-2 com±10% R10 - С2-33Н- 0.25-10 kΩ ± 10% R11 - S2-33N-0, Ohm ± 10% R12 - S2-33N-0.25-15 kΩ ± 10% Semiconductor diodes VD1, VD2 - KD510A VD3 - D814B VD5, VD6 - KD510A Transistors VT1 VT3 - KT3102 BM 20

GIPPO-1M fire and security control panel The GIPPO-1M fire and security control panel is designed to monitor the state of the alarm loop (AL), both in stand-alone mode with switching on

1 General information RECEIVING AND CONTROL DEVICE SECURITY AND FIRE PKOP 051-1-3 UOTS-1-1A USER'S MANUAL Thank you for choosing the device "UOTS-1-1A" manufactured by NPO "Siberian ARSENAL". you purchased

Control panel Fire and security control panel 051-1-3 УОТS-1-1А

TERMINAL DEVICE UO-2 OF THE INFORMATION SYSTEM "FOBOS-3" Operation manual АЦДР.425632.002 РЭ 2002 Contents Page Introduction 1 1 Description and operation of the product 1 1.1 Purpose of the product

RESERVED POWER SUPPLY OF THE RIP-24 fire alarm system rev.01 Label ATSDR.436534.002-01 ME61

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ (UOTS-1-1A) version 3 OPERATION MANUAL BB02 UP001 Dear customer! Thank you for choosing our products. In the creation of modern high-quality

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE CONTROL PKOP 0104059-1-2 "SIGNAL - SPI" ATSDR.425513.003 RE Operating manual Contents Page. Introduction 1 1 Description and operation of the product 1 1.1 Purpose

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE CONTROL PKOP 0104059-1-1/01 "SIGNAL-VKP" Operation manual АЦДР.425513.001-01 RE CONTENTS Introduction.3 1. Description and operation of the device.. .3 1.1 Purpose

ISO "Orion" Fire and security control panel These installation instructions contain instructions that allow you to perform the basic steps for installing and preparing the "Signal-20M" device for operation.

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE CONTROL PKOP 01004059-4-1/03 "SIGNAL-VK-4P" Operation manual ATsDR.425513.001-03 RE CONTENTS Introduction 3 1. Description and operation of the product ... 3 1.1 Purpose

TERMINAL DEVICE UO-2 OF THE INFORMATION TRANSMISSION SYSTEM "FOBOS-3" Operation manual АЦДР.425632.002 РЭ 2007 CONTENTS Page. Introduction...4 1 Description and operation of the product...4 1.1 Purpose of the product...4

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ OPTION 1 OPERATING MANUAL UP001 General information 1 18 Thank you for choosing the QUARTZ device manufactured by NPO Siberian ARSENAL. This product

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ variant 3 OPERATING MANUAL SAPO.425513.006 RE Certificate of Conformity С-RU.ПБ01.В.00877 Dear Buyer! Thank you for choosing our

POWER SOURCES BBP-0, BBP-0, BBP-0, BBP-00 TU 00 CERTIFICATE OF CONFORMITY TS RU C-RU.AL.B.0 Series RU 00 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the operating rules

POWER SUPPLY BBP-24 TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY TS RU C-RU.AL16.B.02558 Series RU 0228076 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

POWER SUPPLY BBP-20M TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY CU RU C-RU.AL16.B.02558 Series RU 0228076 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

POWER SUPPLY BBP-200 TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY TS RU С-RU.AB24.B.04521 Series RU 0477342 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

RESERVED POWER SUPPLY RIP-12 version 05 (RIP-12-8/17M1) Label ATSDR.436534.001-09 FL 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply RIP-12 version 05 (RIP-12-8 /17M1)

POWER SUPPLIES BBP-0, BBP-0, BBP-0, BBP-00 TU 00 CERTIFICATE OF CONFORMITY TS RU C-RU.AB.0 Series RU 0 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the operating rules

Operating instructions Redundant power supply without battery RIP-12 version 03 for battery 7 Ah 242872

ISO "Orion" Fire and security control panel "Signal-20P isp.01", "Signal-20P SMD" Installation instructions ATSDR.425533.001-01 IM

RESERVED POWER SUPPLY FOR RIP-12 OPS EQUIPMENT 05 Label ATSDR.436534.001-09 ET 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for RIP-12 fire alarm equipment

POWER SUPPLY MIP-12 version 02 (MIP-12-1/P3) Label ATSDR.436434.002 ET 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Power supply MIP-12 version 02 (MIP-12-1/P3) ( hereinafter MIP) is intended

ISO 9001 RESERVED POWER SUPPLY FOR EQUIPMENT OPS "RIP-12" isp. 02P Label ATSDR.436534.001-13 ET PB01 1 BASIC TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

Control panel Security and fire QUARTZ version 1 OPERATION MANUAL CONTENTS GENERAL INFORMATION...2 TECHNICAL DATA...3 DEVICE DESIGN...4 INSTALLATION PROCEDURE...5 PREPARATION FOR WORK...5

ISO 9001 RESERVED POWER SUPPLY FOR EQUIPMENT OPS “RIP-12 isp. 06» Label АЦДР.436534.001-12 ET ПБ01 1 BASIC TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

ISO "Orion" Fire and security control panel "Signal-20P isp.01", "Signal-20P"

PASSPORT for uninterruptible power supply BBP-100 POWER SUPPLY BBP-100 TU 4372 006 63438766 11 CERTIFICATE OF CONFORMITY ROSS RU.KhP28.B07734 PASSPORT 1. INTRODUCTION

1 GENERAL INFORMATION Thank you for choosing a device of the "Granit" family, manufactured by NPO "Siberian Arsenal". This product will provide reliable protection of your object from penetration and fire. Control panel device

INTERFACE DEVICE OF RS-232 INTERFACES AND REPEATER OF THE NOTIFICATION SYSTEM "PHOBOS" "USI-Phobos" ATSDR.426469.009 RE Operation manual Contents Page. 1 Description and operation of the product 1 1.1

RESERVED SECONDARY POWER SUPPLY BBP-30 V.4 TS

"APPROVED" Head of SKB ITs A.A. Martsinkevich "_15_" 060 2001 Control unit BU 3 Instructions for setting up and checking RMEA.656116.403 I1 Contents 1. Introduction 3 2. Technical data of the control unit

ISO "Orion" Block voice announcement Spanish horn. 01 Installation manual АЦДР.425541.001-01 IM

K ARIA VOICE WARNING SYSTEM I. Connection diagram for 9, 12, 15, 18, 21, 24 and 27 voice annunciators and P. Terminal resistor rating = 1.5 kΩ ± 5%. VOICE PANEL UNIT to OPERATING MANUAL

DEVICE CONTROL SECURITY - FIRE CONTROL PKOP 0104059-6-1 "Signal VK-6" ATSDR.425513.006 RE Operating manual CONTENTS Introduction 1 1 Description and operation of the product 1 1.1 Purpose of the product 1

Ministry of the Interior Russian Federation Federal government agency"Scientific Research Center "Protection" Novosibirsk branch (NF Research Center "Protection") 43,729 AC voltage stabilizer

SWITCHING DEVICE UK-VK UK-VK version 10 UK-VK version 11 UK-VK version 1 UK-VK version 13 UK-VK version 14 UK-VK type 15 1.1 General information 1.1.1 This label

Operating instructions Pulse secondary power supply OPTIMUS-1230-OD Secondary power supply OPTIMUS 1230-OD ARGP.435520.003TU is designed to provide power

PASSPORT for uninterruptible power supply BBP-20, BBP-30 POWER SUPPLIES BBP-20, BBP-30 TU 4372 001 63438766 12 CERTIFICATE OF CONFORMITY ROSS RU.KhP28.V07734

Insert to the operating manual Pritok-A-KOP-02 LIPG 423141.022 RE 1. BASIC INFORMATION This insert to the operating manual Pritok-A-KOP-02 LIPG 423141.022 RE is a

RESERVED POWER SUPPLY FOR OPS EQUIPMENT RIP-24 version 01 (RIP-24-3/7M4) Label АЦДР.436534.002-01 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

Size: px

Start impression from page:

transcript

1 RECEIVING AND CONTROL DEVICE SECURITY AND FIRE "SIGNAL-VK1", "SIGNAL-VK1" version 01 ATSDR RE Operating manual 2003

2 Contents Introduction 3 1 Description of the device Purpose of the device Characteristics Contents Contents Design and operation of the device Marking Packaging 15 2 Intended use Preparing the device for use Preparing for operation Using the device 18 3 Maintenance 19 4 Maintenance 21 5 Transportation and storage 22 6 Manufacturer's warranties 23 7 Certification information 23 Appendix A Overall and mounting dimensions 24 Appendix B Electrical functional diagram 25 Appendix C Electrical connection diagram of the device 26 Appendix D Diagram of checking the device's performance 27 8 Certificate of acceptance and packaging 28 2

3 This operating manual is intended to study the principle of operation and operation of fire and security control panels PPKOP "Signal-VK1" and PPKOP / 01 "Signal-VK1" isp Description of the device 1.1 Purpose of the device -VK1" and PPKOP /01 "Signal-VK1" version 01, (hereinafter referred to as the device), is designed for centralized and autonomous protection of shops, cash desks, banks, pharmacies, institutions and other facilities from unauthorized entry and fires by monitoring the state of one an alarm loop (AL) with security, fire or security and fire detectors included in it and issuing notifications to the central monitoring station (RCP) using a relay output about violation of the AL and triggering of the detectors; control at the facility by internal light signaling devices, external sound and light annunciators; control of the arming/removal of the device using the built-in magnetically controlled contact; supplying detectors with output "+12 V"; control of opening of the case of the device by means of the switch; change of operating parameters using removable jumpers The device is designed for installation inside a guarded facility and is designed for round-the-clock operation The device is designed for joint operation with centralized monitoring consoles Neva-10, Neva-10M, -KM", "Progress-TS", "Phobos", AWP "Phobos", etc. The following can be included in the alarm loop of the device: - magnetic contact signaling devices IO102-2, IO102-4, IO102-5, IO102-6, sensors such as "Foil", "Wire"; - shock-contact detectors "Window-6"; - optoelectronic, ultrasonic and radio wave detectors "Photon-6", "Photon-6A", "Photon-6B", "Photon-8", "Photon-8A", "Photon-8B", "Photon-9" ", "Photon-Sh", "Photon-SK", "Photon-SK2", "Astra-MS", "Argus-2", "Argus-3", "Echo-3", "Showcase", "Echo -3", "Echo-A", "Wave-5" and the like; - detectors of acoustic type "Harp", "Glass-1", "Glass-2-1", "Glass-3"; - detectors of capacitive type "Peak"; - detectors security combined "Falcon-2"; - detectors of piezoelectric type "Gran-2", "Shoroh-1-1"; - output circuits of receiving and control devices; - thermal fire detectors "IP 101-2", "IP 103-5", "IP103-7", etc. batteries with output of signals to remote light and sound annunciators and a built-in indicator. Transmission of notifications to the monitoring station about an alarm or fire is carried out using relay contacts. The transmission of a notification of a malfunction is carried out using the "open collector" (OK) output.

4 with a nominal voltage of 12 V and a capacity of 1.2 Ah or an external backup DC source with a voltage of (12 +2.2-0.6) V installation inside a protected facility and is designed for round-the-clock operation. The design of the device does not provide for its use in conditions of exposure to aggressive environments, dust, as well as in fire hazardous rooms. By the type of maintenance, the device belongs to products with periodic maintenance. The average total operational duration of maintenance is not more than 0.15 hours per month. The device is designed for operation in the following conditions: - ambient operating temperature range from 243 to 323 K (from minus 30 to K (from minus 10 to +50 ° C) with a rechargeable battery. - relative humidity at an ambient temperature of 298 K (+25 ° C) up to 98%; - vibration loads in the range from 1 to 35 Hz with a maximum acceleration of 0.5 g In terms of protection from environmental influences, the device has an ordinary design according to OST The device belongs to single-function, restored, repaired and serviced products of group II type 1 according to GOST operation - exponential An example of recording the designation of the device when ordering it and in the documentation of other products is given in Table 1. Table 1 Designation OKP code Example of recording when ordering the execution АЦДР АЦДР Fire control and control device PPKOP "Signal-VK1" ATSDR TU Fire control and control device PPKOP /01 "Signal-VK1" version 01 ATSDR TU 1.2 Characteristics General requirements The device complies with the requirements of GOST R, and a set of design documentation in accordance with ATSDR in due course Main parameters and dimensions The device remains operational in the range of supply voltages from 187 to 242 V when powered by AC mains with a frequency of (50 ±1) Hz The device remains operational in the voltage range (11.6...14.2) V from the built-in battery a rechargeable battery with a nominal voltage of 12 V and a capacity of 1.2 Ah in the event of a decrease in the mains voltage below 187 V. Instrument power supply 4

5 can also be carried out in the event of a decrease in the mains voltage below 187 V and the absence of a built-in rechargeable battery, from an external backup DC source with a voltage of (12.0 +2.2-0.6) V. continuous mode, and when performing p in flashing at a frequency of 1 Hz. When the voltage on the battery drops below 10.2 V and there is no mains voltage, the "PIT" indicator turns off. If the mains voltage is present and the voltage on the battery drops to 11.6-10.2 V, the external DC sounder is switched off (if it was turned on). The power consumed by the device from the AC mains in standby mode is not more than 10 V Alarm" no more than 15 VA The current consumed by the device from a backup source, excluding the power supply of active detectors and an external light annunciator, in standby mode when monitoring the loop, no more than 30 mA; in the "Alarm" mode 0.7 A (with the siren on). Current consumed from a backup source, taking into account the power supply of active detectors, no more than 90 mA when monitoring a security loop in standby mode and no more than 0.7 A (with the siren on) in the "Alarm" mode Number of alarm loops connected to the device (information capacity) - one Informativeness of the device, in accordance with GOST, is given in Table 2. Table 2 Designation of the ADCDR device Types of notifications "Norma" in the alarm loop on the monitoring station "Alarm" in the alarm loop on the monitoring station "Norma" in the alarm loop on the built-in indicator "AL" "Alarm " in AL to the built-in indicator "AL" "Normal" to the external DC light annunciator "Alarm" to the external DC light annunciator "Alarm" to the external DC sound annunciator "Network OK" - to the built-in indicator "POWER" "Accident mains" - to the built-in indicator "PIT" "Power failure" to the built-in indicator "PIT" "Fire" in the loop on the monitoring station "Fire" in the loop to the built-in indicator "PS" and the remote DC light annunciator "Fire" in the loop on the remote sv DC signaling device "Fault" in the loop to the output "FAULT" "Fault" in the loop to the built-in indicator "AL" and a remote DC light annunciator "Fault" in the loop to the remote DC sounder 5

6 The device provides switching of remote light and sound annunciators and FAULT output in accordance with Table 3. Table 3 established species sirens and external devices Switching current in circuits, A 12 V External sound DC 0.6 Remote light DC 0.05 with battery FAULT output 0.1 ADDR without battery Remote sound DC 0.06 Remote light DC 0.05 FAULT 0, The device provides operability in the following modes of operation: - removed (the state of the alarm loop is not analyzed); - transitional (alarm violation is not remembered); - duty officer (alarm control); - alarms (violation of AL is remembered); - malfunction (short circuit or break in the AL. Violation of the AL is not memorized); - fire (alarm violation is stored) Depending on the position of removable jumpers "1", "2" and "ACC", the device provides functions in accordance with those specified in Table 4. Table 4 "1" "2" AL Siren turn-on delay yes yes Burg , 30 sec with automatic override and saving alarm indication yes no Burg, 30 sec with forced control no yes Burg, 0 sec with forced control no no Fireman - "ACC" installed jumpers "1" and "2" in the mode burglar alarm repeated violation of the alarm loop leads to re-enabling the sound annunciator for 2 minutes, while the indicator of the ShS device and the light annunciator continue to glow with intermittent light. The sound annunciator turns on with a delay of 30 s. When jumper "1" is installed and jumper "2" is removed in the alarm mode, when the device is in alarm mode, the restoration of the loop and its repeated violation does not turn on the sounder, while the sounder after the first violation of the loop turns on with a delay of 30 s . 6

7 If jumper "1" is removed, jumper "2" is installed in the security alarm mode, when the device is in alarm mode, the restoration of the loop and its repeated violation does not turn on the sounder, while the sounder after the first violation of the loop is turned on immediately. When jumpers "1" and "2" are removed in the fire alarm mode, the device switches to the "Fire" mode when thermal or smoke fire detectors with normally closed contacts are triggered. The device goes into the "Fault" mode in case of a short circuit or open loop. When the "ACC" jumper is set, the device does not analyze the state of the battery and analyzes when the jumper is removed. The device in the alarm mode operates in the following states: armed, disarmed, "Alarm" Arming and disarming the device. Taking and removing the device is carried out using a built-in magnetically controlled contact. For the duration of the operation of the magnetically controlled contact, the "SHS" indicator and the remote light annunciator switch to a flashing mode with a frequency of 6 Hz. Taking the device is also carried out automatically when power is supplied. At the same time, the relay contacts of the monitoring station close and after 60 s the "ShS" indicator and the remote light annunciator turn on to the continuous glow mode. In the transition mode, for 60 s, the "ShS" indicator and the remote light annunciator turn on in the intermittent glow mode. 0.25 s are on and off for 1.5 s, indicating that the transition to the standby mode is in progress. Violation of the alarm loop in the transient mode is not remembered, however, the CMS indicator opens, and the "AL" indicator and the remote light annunciator turn on in the intermittent glow mode with a frequency of 1 Hz. The device is removed by bringing the magnet into the zone of operation of the magnetically controlled contact, while the "AL" indicator, remote light and sound (if it was turned on) annunciators are turned off, the relay contacts of the monitoring station open. mode depend on the state of the loop (armed or disarmed) as follows: - if the loop is disarmed, the "disarmed" mode is provided, the state of the loop is not analyzed, the status indicator of the loop is off, the relay contacts of the monitoring station are open, the light and sound annunciators are turned off ; - after arming, the device provides a transitional mode (violation of the loop is not remembered by the device, the "AL" indicator and the light annunciator display the status of the loop, flash at a frequency of 1 Hz, if it is violated, and glow with intermittent light (0.25 s on and 1.5 c is not lit) - if not violated, the contacts of the monitoring station relay are open if the alarm loop is violated, and closed if the alarm loop is not violated). If during arming the loop is initially violated for more than 60 seconds, then the transitional mode continues until the loop is restored. After that, after 1 s, the device switches to standby mode. After the end of the transitional mode, the "ShS" indicator and the light annunciator glow continuously, the contacts of the monitoring station relay close, the device goes into standby mode; - if the alarm loop is violated in the standby mode, the device switches to the alarm mode with the "AL" indicator and the light annunciator turning on in the flashing mode, opening 7

8 contacts of the monitoring station relay, turning on the sounder for 2 minutes and is in this mode until it is disarmed. When jumpers "1" and "2" are installed in the alarm mode, after turning off the sound annunciator and restoring the alarm loop, the device switches to standby mode (automatic override) after 60 s, the CMS contacts close, while the "AL" indicator and the light annunciator remain in flashing mode. A new activation of the alarm loop leads to the activation of the sound annunciator for 2 minutes (in the presence of mains power and a depleted battery, the device remains operational, however, the siren will turn off when the minimum allowable voltage on the battery is reached), the CMS relay contacts open, without changing the status of the "AL" indicator and light annunciator. The sound annunciator turns on with a delay of 30 s. When jumper "1" is installed, jumper "2" is removed in the alarm mode, when the device is in alarm mode, the restoration of the loop and its repeated violation does not turn on the sounder, while the sounder after the first violation of the loop is activated with a delay of 30 s . When jumper "1" is removed, jumper "2" is set in the alarm mode, when the device is in alarm mode, the restoration of the loop and its repeated violation does not turn on the sounder, while the sounder after the first violation of the loop is turned on immediately. In all security alarm submodes, when the device is opened, an "Alarm" signal is generated, as when a sensor with normally closed or normally open contacts is triggered. The device in the fire alarm mode operates in the following states: armed, malfunction, fire. violated) depend as follows: - within 15 s after the power is turned on, the device provides a transition mode and does not remember violations of the AL; - after 15 seconds, the device switches to the "Caught" state; - when a heat or smoke fire detector with normally closed contacts is opened, the device closes the contacts of the monitoring station relay, turns on the sound annunciator in the "Fire" mode for 4 minutes, switches the "SHS" indicator and the light annunciator to the flashing "Fire" mode; - when the loop is opened or closed, the device opens the FAULT output, turns on the sound annunciator in the "Fault" mode, turns on the "AL" indicator and the light annunciator in the "Fault" mode. When the alarm loop is restored, the device switches to the "Accepted" state; - when opening the case of the device, the signal "Fault" is also generated; - to transfer the device to the "Taken" state from the "Fire" state, it is necessary to bring the magnet from the device set to the zone of influence on the magnetically controlled contact. After 15 seconds, the device switches to the "On" state. The device ensures that the indication is turned off and the battery is turned off in the event of a power failure in the AC mains and the voltage on the battery is less than (11.0 ± 0.6) V in standby mode and less than (9.0 ±0.6) in the "Alarm" or "Fire" mode with the siren on. In the event of a power failure in the network 8

9 alternating current, the "PIT" indicator turns on in an intermittent glow mode with a frequency of 1 Hz. The device provides indication "PIT" showing the state of the device's supply voltage, and issues the following notifications to it: - "Network OK" - the "PIT" indicator is on when the voltage in the AC mains is more than 187 V; - "Network failure" - the "PIT" indicator glows with intermittent light with a frequency of 1 Hz in the absence of voltage in the AC network; - "Power failure" - the "PIT" indicator is off when the voltage in the backup power supply circuit (battery) is less than (11.0 ± 0.6) V in standby mode and less than (9.0 ± 0.6) in " Alarm", "Fire" and in the absence of voltage in the AC mains Duration of operation of the device from the built-in backup battery with a capacity of 1.2 Ah without additional external consumers is at least 24 hours in standby mode and at least 3 hours in the "Alarm" mode, " Fire" When the security and fire detectors are turned on in the alarm loop, the device is in standby mode when the following parameters AL: 1) resistance of the AL wires, excluding the remote element - no more than 100 Ohm; 2) leakage resistance between the loop wires or each wire and the "ground" - at least 20 kΩ The device remains in standby mode if the loop is violated for a time less than 50 ms (250 ms - for the fire alarm mode) with loop resistance (2 6) kΩ ± 10%, taking into account the resistance of the external element, as well as when the resistance of the alarm loop changes slowly in the above range at a rate of up to 10% per 1 hour (only for the alarm mode) The device switches to the "Alarm" mode when the resistance of the alarm loop goes out of the range (2 6) com ±10% for a time of 70 ms or more, as well as with an abrupt change in the resistance of the security loop by 10% or more relative to the current value in the range (2 6) com ±10%. The device switches to the "Fire" state when the thermal or smoke detector with normally closed contacts. The device goes into the "Fault" state when the loop opens or closes for 300 ms or more (an increase in the resistance of the loop is more than 50 kΩ or a decrease in it is less than 100 Ohm) The device provides a constant voltage of 10 to 14 V at the input of the loop in standby mode. AL voltage at the input of the AL is not more than 14 V The value of the ripple voltage in the AL is not more than 20 mV (effective value) The device supplies power to active detectors with the following parameters: 1) supply voltage - (12+1.8-2.2) V; 2) consumed current - no more than 60 mA. The value of the ripple voltage at the power output of active detectors with a voltage of 12 V is not more than 20 mV (effective value). When powered from the mains, the device restores its functionality after a short circuit (up to 60 s) of the power supply circuit of active detectors. 9

10 The device provides automatic switching of power supply to the built-in rechargeable battery in case of mains voltage failure and back without issuing an alarm notification. Instrument of execution 01 is supplied without a battery. The instrument ensures the issuance of alarm notifications to the monitoring station by opening the relay contacts in the event of a complete power outage (in the alarm mode) The instrument ensures the transmission of "Alarm" and "Fire" notifications to the electrical circuits with a maximum voltage up to 80 V and a maximum current up to 50 mA voltage values ​​up to 1 V The device does not issue false notifications after exposure to external electromagnetic interference (EMI) of the second degree of severity according to GOST R Radio interference created by the device during operation does not exceed the values ​​specified in GOST R 1) operating temperature of the ambient air from 243 to 323 K (from minus 30 to +50 ° C) and from 263 to 323 K (from minus 10 to +50 ° C) for a device with a battery; 2) relative humidity up to 98% at 298 K (+25 o C); 3) vibration loads in the range from 1 to 35 Hz with a maximum acceleration of 0.5 g Time of technical readiness of the device for operation, after turning on its power supply, no more than 3 s The device in the package withstands during transportation: 1) transport shaking with an acceleration of 30 m / s 2 at a frequency of 80 to 120 beats per minute or beats; 2) temperature from 223 to 323 K (from minus 50 to C); 3) relative humidity (95±3)% at 308 K (+35 0 C) Mean time between failures of the device in the standby mode of operation - not less than an hour, which corresponds to the probability of failure-free operation of 0.97 per 1000 h instrument during repair work- no more than 60 min. The average service life of the device is 10 years. It is necessary to replace the battery in the device at least once every 5 years. The weight of the device is not more than 1.5 kg (with a battery with a capacity of 1.2 Ah) and not more than 0.8 kg (without a battery) Overall dimensions of the device are not over 151 x 157 x 71 mm. ten

11 1.3 Complete set The delivery set of the device corresponds to that specified in Table 5. Table 5 Qty. Designation Designation Design ATSDR Fire and security control panel PPKOP "Signal-VK1" ATSDR Fire and security control panel PPKOP /01"Signal-VK1" isp. 01 Set of spare parts: Resistor OZHO TU S2-33N-0.5-4.7 kΩ±5% Magnet in case 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. Note Screw 1-4x GOST pcs. 3 pcs. Battery 12 V, 1.2 Ah 1 pc. - Supplied by separate order Control panel, security and fire PPKOP "Signal-VK1". Operation manual 1 copy. 1 copy Note 1 Delivery of group SPTA kits is carried out under a separate contract according to the SPTA list. 2 It is allowed to supply devices with a switching device "UK-VK" to enable control through the outputs to light and sound annunciators (with an external power supply connected) of circuits energized with 220 V alternating current with a current of up to 0.8 A or up to 10 A 1.4 Design and operation of the device The device is structurally made in the form of a box, consisting of a plastic base and a cover, the appearance of the device and its overall dimensions are given in Appendix A. A printed circuit board with radio elements is fixed on the base, on the reverse side of the base there are two shaped and one round holes for fixing, with the help of which the device is fixed on the wall in the working position. The electrical functional diagram of the device is given in Appendix B. The electrical connection diagram of the device is given in Appendix C. The device consists of the following functional units: - connection unit; - input block; - rectifier; - voltage stabilizer 15 V; - keys 1, 2, 3; - voltage stabilizer 5 V; eleven

12 - processor; - coordination with ShS; - setting the operating mode of the device; - devices for emergency shutdown of the battery; - devices for recharging and matching with the battery; - control of taking-off of the device; - backup power supply; - output "Fault"; - protection against opening; - "ShS, PIT" indicators. active detectors that require a separate power source The input unit contains a mains fuse and a step-down mains transformer with a thermal fuse installed inside it Rectifier contains a bridge rectifier and a smoothing capacitor and DC sounders Key 1 contains low power relay, a protective diode and a resistor that limits the current in the CMS circuit, and is designed to send an alarm signal to the CMS. The control action on key 1 is supplied from the processor. Key 2 contains a transistor key, protective diodes and is designed to control the "SHS" indicator and a remote DC light annunciator. The control action on key 2 is supplied from the processor. Key 3 contains a transistor key and is designed to control a remote DC sounder. The control action is applied to key 3 from the processor The +5 V voltage regulator contains an integrated stabilizer, two smoothing capacitors and is designed to power the processor and some consumers requiring a 5 V current source The processor contains an integrated single-chip microcontroller, circuits for setting the reference frequency, ADC reference voltage and is intended to control the operation of the device The node for matching with the AL provides a voltage supply of +12 V through a limiting resistor to the AL and transmits voltage from the AL through a resistive divider to the analog input of the processor for subsequent analysis. The node for setting the device operation modes includes three removable jumpers "1", "2", "ACC" and is intended for changing the current configuration of the device. The battery emergency shutdown device consists of an electronic key, and is designed to disconnect the battery when the voltage on it drops below the permissible level. The device for recharging and matching with the battery consists of a current a limiting resistor for recharging the battery and a matching diode. 12

13 The control unit for taking-off the device consists of a magnetically controlled contact and is designed to control the device with a magnet; The backup power supply unit is designed to connect a backup 12 V DC source. The backup power supply is connected to the +12 V circuit of the device through an isolation diode. The OK output unit is controlled from the processor output and is designed to issue a "Fault" signal to external circuits. opening contains a limit switch and contacts for installing a removable technological jumper that blocks the limit switch and is designed to put the device into alarm mode when the case is opened. The device is supplied without a jumper. In the initial state, the external toggle switches S1 and S2 are open, the device is de-energized (Appendix B). When the toggle switch S1 is closed, the supply voltage of 220 V is supplied to the device. The device starts to work depending on the installed configuration using jumpers "1", "2" and "AKK": - "Normal" mode - with loop resistance (from 2 to 6) kΩ ± 10%, in security and fire modes; - "Alarm" mode - if the loop resistance is less than 1.7 kΩ or more than 5.4 kΩ in the security mode; - "Fault" mode when the loop resistance is less than 100 Ohm or more than 50 kΩ, in fire mode; - "Fire" mode with loop resistance greater than 5.4 kΩ, but less than 40 kΩ in fire mode. In the "Normal" mode, the processor closes Key 1 and Key 2, thus turning on the built-in LED indicator, and the "Indicator" (remote DC light signaler). All indicators should glow continuously. In the "Alarm" mode (in security mode), i.e. in case of violation of the normal state of the AL resistance (the value of the AL resistance is less than 1.7 kΩ or more than 5.4 kΩ), the processor opens Key 1, transmitting an "Alarm" signal to the monitoring station, switches the built-in "AL" indicator and the remote light indicator to intermittent glow with a flashing frequency of 1 Hz. In the "Fault" mode (in fire mode), that is, in the event of a violation of the normal state of the loop (the resistance value of the loop is less than 100 Ohm or more than 50 kΩ), the processor opens the OK output, transmitting a "Fault" signal to the monitoring station, switches the indicator and the light annunciator to intermittent glow mode: 0.5 s on, 3.5 s off, turns on the sounder in the mode: 0.5 s on, 3.5 s off. When the normal state of the AL is restored, the processor switches to the "Normal" mode. In "Normal" mode, all indicators glow continuously. In the "Alarm" mode, the processor opens Key 1, transmitting an "Alarm" signal to the monitoring station, switches all indicators to intermittent light with a flashing frequency of 1 Hz and closes Key 3, including "Siren" (remote sounder DC) for 2 minutes. Moreover, depending on the state of jumpers "1" and "2", the remote sounder is switched on immediately upon the appearance of the "Alarm" mode or with a delay of 30 seconds, or the device is automatically re-armed after the siren stops working. 13

14 In the "Fire" mode (with jumpers "1" and "2" removed), the indicator and light annunciators glow with intermittent light at a frequency of 1 Hz. The sound annunciator operates in the following mode: 0.5 s on, 0.5 s off, for 4 min. The ARC relay contacts are closed, transmitting the "Fire" signal. In the "Fault" mode (with jumpers "1" and "2" removed), the indicator and light annunciator glow in the mode: 0.5 s on, 3.5 s off. The sound annunciator operates in the following mode: 0.5 s on, 3.5 s off. The OK output opens, transmitting a "Fault" signal. When the normal state of the alarm loop is restored, the device switches to the "Normal" mode. When the "Alarm", "Fire" mode occurs, the processor remembers it and does not return the device to the "Normal" mode even after the loop returns from the "Alarm", "Fire" mode to the "Normal" mode. This state of the processor can be removed only by acting on the magnetically controlled contact or by completely turning off the supply voltage (with the built-in battery disconnected). The device can operate from a backup 12 V source connected to the connection unit or from the built-in battery. The power supply from the reserve source is switched on by the toggle switch S2 (see Appendix B). In the absence of mains voltage, the "POWER" indicator switches to a flashing mode with a frequency of 1 Hz. Otherwise, the operation of the device is the same as with mains supply voltage. 1.5 Marking Marking of the device corresponds to the set of design documentation and contains: 1) trademark of the manufacturer; 2) symbol of the device; 3) serial number; 4) mark of conformity; 5) quarter and year of manufacture (last two digits) The marking of the external terminals of the device corresponds to the electrical circuit diagram device. Near the mains voltage connection node, the rated voltage of the supply network is 220 V. The method of application and the quality of the inscriptions and designations provide sufficient contrast, allowing the inscriptions to be read in normal lighting throughout the entire life of the device. The marking of the consumer packaging of the device complies with the requirements of GOST and contains: 1 ) trademark of the manufacturer; 2) symbol of the device; 3) the number of devices; 4) month and year of packaging; 5) serial number; 6) signature or stamp of the person responsible for packing. Marking of the transport container corresponds to the drawings of the manufacturer, contains: the trademark of the manufacturer; symbolic designation of the product; number of products; gross weight; month and year of packing; has 14

15 handling signs: "Caution, fragile!", "Afraid of dampness", "Up, do not tilt"; basic, additional and information inscriptions in accordance with GOST Packaging Preservation of devices is carried out in accordance with GOST for product group III-3 with the option of temporary anti-corrosion protection VZ The devices are packed in consumer packaging - cardboard box type III-I GOST, a set of spare parts, operational documentation for the device, packed in a bag of polyethylene film GOST The edges of the package are welded The group spare parts are placed in plastic bags. The edges of the packages are sealed. Boxes with packed devices, a list of spare parts, group spare parts (if any) are placed in a shipping container - boxes of type II-I GOST, lined with GOST bituminized paper Each box (or container) contains a packing list containing the following information: 1 ) name and designation of devices and their number; 2) designation and quantity of group spare parts and accessories (if any); 3) month and year of packaging; 4) signature or stamp of the person responsible for packing. It is allowed to pack devices in containers in accordance with GOST. Net weight - no more than 40 kg. Gross weight - no more than 50 kg. 2 Intended use 2.1 Preparing the device for use Safety precautions when preparing the device When operating the device, observe the current "Rules for the technical operation of consumer electrical installations" and "Safety regulations for the operation of consumer electrical installations". The sources of danger in the device are: - contacts ХТ1:1 and ХТ1:3 for connecting the AC mains. Installation, installation, maintenance should be carried out with the mains voltage disconnected from the device. It is forbidden to use fuses that do not correspond to the nominal value. Installation and maintenance of the device must be carried out by persons with a safety qualification group of at least the third. Installation procedure The device is installed on the walls or other structures of the guarded premises in places protected from atmospheric precipitation, mechanical damage and access by unauthorized persons. Light annunciators must be placed in places that are well visible to the facility management agency after leaving the premises. fifteen

16 Installation of the device, light and sound annunciator is carried out in accordance with the RD "Rules for the production and acceptance of work. Installation of security, fire and security fire alarms." Install the device in the following sequence: - determine the location of the device; - to make a marking of fastening, to mount elements of fastening; - install the device on the fasteners. Mount the alarm loop and connecting lines in accordance with the wiring diagram given in Appendix C. Connect the connecting lines to the terminals of the device in the following sequence: - connect the wires of the remote DC light annunciator to contacts 11 and 12 of ХТ2 observing the polarity; - connect the wires of the remote DC sounder to contacts 1 and 2 of XT2 observing the polarity; - connect the AL wires to contacts 7 and 8 of XT2; - connect the power supply circuits of the detectors to contacts 3 and 4 of XT2 observing the polarity; - connect the remote control lines to pins 5 and 6 of XT2; - connect external circuits "Fault" to contacts 13 and 4 XT2; - connect the lines from the backup DC source to contacts 9 and 10 of XT2, taking into account the polarity; - connect the AC mains wires to pins 1 and 3 of XT1; - AC mains supply and standby DC supply must be connected to the instrument through switches that are used to turn off the instrument. The backup power supply switch S2 must be installed in the circuit: positive output of the power supply - terminal XT2:10. Switch S1 must be installed in the phase conductor of the network. When turning off the device, both power supplies must be turned off. Failure to turn off the backup DC source will cause it to discharge. If the device is turned off for a long time, the built-in battery must be disconnected from the device. 2.2 Preparing for operation Check the correctness of the installation and test the device performance when powered from the AC mains in one of the operating modes: security alarm (jumpers "1" and "2" are installed) or fire alarm (jumpers "1" and "2" removed) in the following order. Check in burglar alarm mode. Put the alarm loop on standby by closing doors, windows, transoms, etc.. Check the operation of the device during the initial switching on. Apply mains voltage to the device. Within 1 min after the power is turned on, simulate the violation and restoration of the AL. If the loop is in good condition, the remote DC light annunciator and the built-in indicator should glow with intermittent light, 0.25 s on, 1.5 s off, if the loop is violated, with intermittent light at a frequency of 1 Hz. The remote DC sounder must be turned off. Check the value of the delay from the moment the loop is violated to the activation of the sound annunciator. The delay value must be at least 30 s if the device has removable 16

17 jumpers "1" and "2" are set, and the delay is zero if jumper "1" is removed and jumper "2" is set. Check the operation of the device in standby mode and in alarm mode. Violate the alarm loop - open the front door and leave it open. Apply mains voltage to the device. The remote DC beacon and the built-in indicator begin to glow with intermittent light at a frequency of 1 Hz. The remote DC sounder must be turned off. Close the front door, while the glow mode of the remote light annunciator and the built-in indicator should become intermittent - 0.25 s are lit, 1.5 s are not lit. After 1.5 minutes, open the front door. The remote light annunciator and the built-in indicator switch to a flashing alarm mode of illumination, and after a delay of 30 s, the external DC sound annunciator turns on for 2 minutes. Close the front door. The nature of the operation of the annunciators should not change. Check the ability of the device to record the operation of each detector included in the alarm loop. Check the ability of the device to work with the centralized monitoring console in the following sequence: 1) switch the device to standby mode and inform the operator at the monitoring station to arm the object; 2) switch the device to alarm mode. The monitoring station operator must determine the violation of the loop. Check the operability of the device according to p when powered by a backup power source or a built-in rechargeable battery. Fire alarm test. Remove jumpers "1" and "2". Put the loop on standby, check the serviceability of the fire detectors included in the loop. Check the operation of the device in the "Fault" mode and in the "Fire" mode. After 15 s after the device is turned on (armed in fire mode), simulate a short circuit and an open loop, triggering fire detectors, and restoring the loop to standby. Violate the alarm loop (open or short circuit). The remote light annunciator and the built-in indicator of the device should glow in the following mode: 0.5 s - lit, 3.5 s off. The remote sound direct current siren must operate in the following mode: 0.5 s - on, 3.5 s off. When the alarm loop is restored to the standby state, the light annunciators and the indicator of the device should turn on in continuous mode, the sound annunciator should turn off, the device switches back to the standby mode. Simulate fire alarm activation. The remote light annunciator and the built-in indicator of the device should glow with intermittent light with a frequency of 1 Hz. The remote sound direct current annunciator must operate in the following mode: 0.5 s - on, 0.5 s off and off after 4 minutes. Turn off power to the device. Check the ability of the device to record the operation of each fire detector included in the alarm loop. Check the ability of the device to work with the centralized monitoring console in the following sequence: 17

18 - switch the device to standby mode and inform the operator at the monitoring station so that the object is taken under control; - transfer the device to the "Fault" mode and back to the standby mode. The operator of the monitoring station must determine the open or short circuit of the fire alarm at the facility, and then the transition of the device to standby mode; - switch the device to the "Fire" mode. The monitoring station operator must determine the activation of the fire detector at the facility. Check the operability of the device according to p when powered from a backup power source and from a built-in rechargeable battery. 2.3 Using the device Arm the facility in the following sequence. When operating in the alarm mode (jumpers "1" and "2" are installed). For other states of jumpers "1" and "2", see Table 4. 1) turn on the instrument's power supplies in series. Using the magnetic key supplied with the device, switch the device to the "Removed" mode; 2) close all windows, vents, doors, etc., on which electrical contact detectors are installed, open the exit door. Using the magnetic key supplied with the device, switch the device to standby mode; 3) at the same time, the remote light annunciator and the built-in indicator should blink, the external DC sound annunciator should not work; 4) inform the CMS duty officer by phone of the conditional number of the object to be guarded, put the handset on the device; 5) leave the protected premises and close the entrance door, while the flashing remote DC light annunciator should switch to the intermittent glow mode 0.25 s on, 1.5 s off, which indicates the restoration of the alarm loop and switching the device to the transition mode . When operating in the fire alarm mode (jumpers "1" and "2" are removed). 1) turn on the power supply of the device and after 15 s, use the light annunciators and the indicator of the device to determine the normal state of the alarm loop and fire detectors; 2) inform the CMS duty officer by phone of the conditional number of the object handed over to the fire department, put the handset on the device; 3) leave the protected premises, close the front door, remote annunciators should glow with a steady light. To disarm the object when opening the premises in the following order. When operating in the burglar alarm mode (jumpers "1" and "2" are set): 1) open the front door, while the remote light network annunciator and the DC annunciator must switch to the flashing mode of operation; 2) go to the device, use the magnetic key from the device kit to switch the device to the "Removed" mode or turn off the power to the device; 3) call the monitoring station by subscriber phone and inform the operator about the disarming of the object. It must be borne in mind that if the time from the moment the door is opened to the device's mains power is turned off or disarmed exceeds 30 s, the sound annunciator will turn on. eighteen

19 When operating in the fire alarm mode (jumpers "1" and "2" are removed), the object is monitored by the monitoring station around the clock, while the power supply of the device is not turned off and the monitoring station controls the object's fire alarm around the clock through two outputs of the device: the "Fault" output and the output Monitoring stations, through which, respectively, information is transmitted to the monitoring station about a malfunction of the alarm loop or the activation of fire detectors. 3 Maintenance Maintenance of the instrument is carried out according to a preventive and preventive system, which provides for annual maintenance. Annual maintenance work is carried out by an employee of the service organization and includes: a) checking the external condition of the device; b) performance check in accordance with section 3.1 of this manual; c) checking the reliability of fastening the device, the condition of external installation wires, contact connections. Checking the performance of the device This technique is intended for engineering and technical workers and electricians of the fire alarm system servicing the technical means of the security and fire alarm system (TS FFS), performing a check of the technical condition (input control), and includes checking the health of the device in order to identify defects and evaluate them. technical condition. Non-compliance of devices with the requirements specified in this procedure is the basis for filing claims with the manufacturer and calling his representative to continue checking and resolving the issue of eliminating defects. Checking the technical condition of devices is organized by laboratories and repair shops of security units and is carried out by maintenance personnel who have studied the principle of operation of the device and this methodology and have a qualification of at least 3 category electricians of the OPS. The check is carried out under normal climatic conditions in accordance with GOST: 1) ambient temperature - () О С; 2) relative air humidity - (45-80)%; 2) atmospheric pressure mm Hg. (84-106.7) kPa. The check is carried out using a stand for general testing of the device, the electrical circuit diagram of which is shown in Appendix D. The total time for checking the technical condition of one device is not more than 40 minutes. Notes: 1 Connection and disconnection of wires during checks should be carried out with the instrument and stand powered off. 2 All checks should be carried out taking into account the time of technical readiness of the device no more than 3 s. Check the device in the following sequence: Check the condition of the packaging and unpack the device. Check the scope of supply in accordance with the operation manual of the ADDR RE, the presence and composition of spare parts and accessories. Make sure that there is no mechanical damage to the instrument case. Shake the device to make sure that there are no foreign objects inside it. 19

20 Check the fastening of the terminal block. Check the presence, compliance with the rating and serviceability of the fuses of the device. Check the compliance of the device number and date of issue specified in the OM. The control of the main technical characteristics of the device is carried out using a general test stand (Appendix D). Set switches S1 S7 on the stand to the off position. Connect the stand to AC mains. Turn on the switch NETWORK of the stand and use the variator A5 to set the supply voltage of the device (220 ± 5) V, controlling it with the voltmeter PV3. Turn off the NETWORK switch. Turn on the DC source A3 and set its output voltage (12 ± 0.5) V, controlling it with a voltmeter PV2. Install jumpers "1" and "2". Turn on the switch NETWORK of the stand and at the same time turn on the stopwatch. The built-in indicator of the device and the INDICATOR of the stand should glow with intermittent light 0.25 s on and off for 1.5 s if the loop is not violated and glow with intermittent light at a frequency of 1 Hz if it is violated. The indicator of the monitoring station stand should display the current state of the loop; it lights up if the loop is not violated and does not glow if it is violated. The SIREN indicator should not light up. Fix the time until the indicators of the device and the INDICATOR of the stand turn on in the continuous glow mode, which should be 60 s. Briefly press the OPEN switch S2 of the stand. Measure, using a stopwatch, the delay time for turning on the SIRENA indicator, which should be 30 s, and then the time for turning on the SIRENA indicator, which should be 2 minutes. The monitoring station indicator should turn off. Using a stopwatch, measure the frequency of blinking of the built-in indicator of the device and the INDICATOR of the stand; determine the frequency as the quotient of the number of flashes divided by the selected time (10 s). For correct operation of the device, the flashing frequency should be 1 Hz. Bring the magnetic key from the set of the device into the zone of influence on the magnetically controlled contact. While the magnetic key is held in the zone, the AL indicator of the device and the INDICATOR indicator of the stand should glow with intermittent light with a frequency of 6 Hz. The built-in indicator of the device and the indicators INDICATOR, SIREN and CMS of the stand must be turned off. Bring the magnetic key to the affected area again and remove it. The device should start working after n Turn off the POWER switch of the stand. Remove jumpers "1" and "2". In this case, the device is configured to operate in fire mode. Turn on the switch NETWORK of the stand and at the same time turn on the stopwatch. The built-in indicator of the device, indicators of the stand INDICATOR, SIREN and CMS should not glow. Record the time until the indicator of the device and the indicator of the INDICATOR stand turn on, which should be no more than 15 s. Press the "Open" switch S2 or "Short circuit" S6 of the stand. The FAULT indicator should turn off. Using a stopwatch, measure the time of the on and off state of the indicator of the device, the indicator of the INDICATOR stand, which should be, respectively, 0.5 s and 3.5 s. Press the "Open" switch S2 or "Short circuit" S6 of the fire alarm loop simulator. The device should go into standby mode. twenty

21 Press and release switch S5 of the stand. The monitoring station indicator should turn on. Using a stopwatch, measure the time when the SIREN indicator is on in the mode: 0.5 s on, 0.5 s off, which should be 4 minutes. Turn off the switch NETWORK of the stand. Install jumpers "1" and "2". Press the OPEN switch S2 and turn on the POWER switch of the stand. Use voltmeters PV4 and PV2 to measure the voltage in the alarm loop and the power supply circuit of the detectors, which, respectively, should not exceed (12 +1.2-1.8) V. Press the OPEN switch S2. Use a voltmeter PV1 to measure the voltage in the loop and the power supply circuit of the detectors, which, respectively, should be (10-13) V and (12.0 +1.2-1.8) V. Turn off the POWER switch of the stand. Disconnect S1 (output 12 V), indicators INDICATOR, SIREN from the stand and turn on the NETWORK switch. Measure the current consumed by the device with a PA3 milliammeter, which should be no more than 30 mA. Turn on the RESERVE switch of the stand and turn off the switch of the stand NETWORK. The device must remain in the standby mode of operation - the indicator of the monitoring station must be lit. Measure the current consumed by the device with a PA1 milliammeter, which should be no more than 90 mA. Use voltmeters PV1 and PV4 to measure the voltage in the alarm loop and the power supply circuit of the detectors, which, respectively, should be (10-13) V and (12.0 + 1.2-1.8) V. Make an entry in the repair log and the input control of OPS means on the results of the audit. 4 Maintenance The list of instrumentation required for repair in a workshop is given in Table 4.2, the approximate consumption of components and materials necessary for servicing and repairing the device is in Table 4.3. Table 4.1 Fault name, Probable cause Elimination method External manifestation and additional symptoms 1 When the mains power supply is turned on No power supply Check for the presence of the source Built-in voltage does not light up Mains voltage LED indicator Faulty fuses Replace the fuses "PIT" of the mains supply in the device Faulty LED Replace LED Faulty Replace 2 When the mains supply is turned on, the fuse fails thermal fuse Short circuit in the secondary or primary circuits of the transformer, breakdown of the bridge rectifier, breakdown of the capacitor thermal fuse Check the transformer, bridge rectifier, capacitor. Replace defective elements 21

GIPPO-1M fire and security control panel The GIPPO-1M fire and security control panel is designed to monitor the state of the alarm loop (AL), both in stand-alone mode with switching on

1 General information 051-1-3 SECURITY AND FIRE RECEIVING AND CONTROL DEVICE UATS-1-1A USER'S MANUAL Thank you for choosing the "UOTS-1-1A" device manufactured by NPO "Siberian ARSENAL". you purchased

POWER SUPPLY BBP-200 TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY TS RU С-RU.AB24.B.04521 Series RU 0477342 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

Control panel Fire and security control panel 051-1-3 УОТS-1-1А

RESERVED POWER SUPPLY OF THE RIP-24 fire alarm system rev.01 Label ATSDR.436534.002-01 ME61

POWER SUPPLY BBP-24 TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY TS RU C-RU.AL16.B.02558 Series RU 0228076 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

POWER SOURCES BBP-0, BBP-0, BBP-0, BBP-00 TU 00 CERTIFICATE OF CONFORMITY TS RU C-RU.AL.B.0 Series RU 00 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the operating rules

POWER SUPPLIES BBP-0, BBP-0, BBP-0, BBP-00 TU 00 CERTIFICATE OF CONFORMITY TS RU C-RU.AB.0 Series RU 0 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the operating rules

TERMINAL DEVICE UO-2 OF THE INFORMATION SYSTEM "FOBOS-3" Operation manual АЦДР.425632.002 РЭ 2002 Contents Page Introduction 1 1 Description and operation of the product 1 1.1 Purpose of the product

POWER SUPPLY BBP-20M TU 4372 002 63438766 14 CERTIFICATE OF CONFORMITY CU RU C-RU.AL16.B.02558 Series RU 0228076 PASSPORT INTRODUCTION This passport is intended for the maintenance personnel to study the rules

Fire and security control panels PPKOP 0104059-1-4 "Signal-VKA", series 01 PPKOP 0104059-1-4/01 "Signal-VKA", version 01 series 01 Operating manual ATSDR.425513.011 RE 2001 C o d e r g

PASSPORT for uninterruptible power supply BBP-100 POWER SUPPLY BBP-100 TU 4372 006 63438766 11 CERTIFICATE OF CONFORMITY ROSS RU.KhP28.B07734 PASSPORT 1. INTRODUCTION

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ (UOTS-1-1A) version 3 OPERATION MANUAL BB02 UP001 Dear customer! Thank you for choosing our products. In the creation of modern high-quality

PASSPORT for uninterruptible power supply BBP-20, BBP-30 POWER SUPPLIES BBP-20, BBP-30 TU 4372 001 63438766 12 CERTIFICATE OF CONFORMITY ROSS RU.KhP28.V07734

TERMINAL DEVICE UO-2 OF THE INFORMATION TRANSMISSION SYSTEM "FOBOS-3" Operation manual АЦДР.425632.002 РЭ 2007 CONTENTS Page. Introduction...4 1 Description and operation of the product...4 1.1 Purpose of the product...4

Operating instructions Redundant power supply without battery RIP-12 version 03 for battery 7 Ah 242872

RESERVED POWER SUPPLY FOR RIP-12 OPS EQUIPMENT 05 Label ATSDR.436534.001-09 ET 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for RIP-12 fire alarm equipment

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ variant 3 OPERATING MANUAL SAPO.425513.006 RE Certificate of Conformity С-RU.ПБ01.В.00877 Dear Buyer! Thank you for choosing our

POWER SOURCES BBP-0, BBP-5, BBP-20, BBP-24 PASSPORT 437 00 080570 03 PS. INTRODUCTION This passport is intended for the maintenance personnel to study the rules for operating power supplies BBP-0, BBP-5,

ISO 9001 RESERVED POWER SUPPLY FOR EQUIPMENT OPS “RIP-12 isp. 06» Label АЦДР.436534.001-12 ET ПБ01 1 BASIC TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

DEVICES RECEPTION - CONTROL SECURITY - FIRE PPKOP 0104059-2-1 "Signal VK2", PPKOP 0104059-2-1 / 01 "Signal-VK2" isp. 01 АЦДР.425513.013 РЭ Operation manual 2002 CONTENTS Introduction 3 1 Description

RESERVED POWER SUPPLY RIP-12 version 05 (RIP-12-8/17M1) Label ATSDR.436534.001-09 FL 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply RIP-12 version 05 (RIP-12-8 /17M1)

POWER SUPPLY MIP-12 version 02 (MIP-12-1/P3) Label ATSDR.436434.002 ET 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Power supply MIP-12 version 02 (MIP-12-1/P3) ( hereinafter MIP) is intended

Inv. duplicate Signed and date Ref. Perv. appl. Vzam. inv. АЦДР.425513.013 CONTENTS Introduction 3 1 Description and operation of the device 3 1.1 Purpose of the device 3 1.2. Characteristics 5 1.3. Contents 22 1.4 Device

1 RESERVE-12/5 SECONDARY POWER SUPPLY RESERVED PULSE RESERVE-12/5 PASSPORT TU 4372-001-79131875-08 2 RESERVE-12/5 1. PURPOSE 1.1. Reserved secondary power supply

RESERVED POWER SUPPLY FOR OPS EQUIPMENT RIP-24 version 01 (RIP-24-3/7M4) Label АЦДР.436534.002-01 1 MAIN TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

ELECTRA Group of Companies www.electra-n.ru RESERVED POWER SUPPLY SOURCE IRP 12-6 Operation manual Voluntary OP066 certification ACCEPTANCE CERTIFICATE Reserved source

ISO 9001 RESERVED POWER SUPPLY FOR EQUIPMENT OPS "RIP-12" isp. 02P Label ATSDR.436534.001-13 ET PB01 1 BASIC TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply for equipment

ELECTRA Group of Companies www.electra-n.ru RESERVED POWER SUPPLY SOURCE IRP 12-6 (24-3) Operation manual Voluntary OP066 certification ACCEPTANCE CERTIFICATE Reserved

1 RESERVE-12/2 SECONDARY POWER SUPPLY RESERVED PULSE RESERVE-12/2 PASSPORT TU 4372-001-79131875-08 2 RESERVE-12/2 1. PURPOSE 1.1. Reserved secondary power supply

LLC NPO MicroComService RESERVED POWER SUPPLY street performance REZERV-12/5U18 (IP56) 12V 5A 18 Ah

CONTROL DEVICE FOR VOICE ALARMS "SONATA-K-20" PASSPORT TU 4372-0-5643358-2005 POCC RU.PB6.V.0027. General information Name: CONTROL DEVICE FOR VOICE SIREN "SONATA-K-20" Date of manufacture:

MP06 UNINTERRUPTIBLE POWER SUPPLY BBP-10, BBP-20, BBP-24 OPERATION MANUAL 4371 001 40267658 04 OM

CONTROL DEVICE FOR VOICE SIREN "SONATA-KL-BR" PASSPORT TU 4372-0-5643358-2005 POCC RU.PB.6.V.0027. General information Name: CONTROL DEVICE FOR VOICE SIREN "SONATA-KL-BR" Production date:

26.30.50.129 UNINTERRUPTIBLE POWER SUPPLY BRP-12 version 1 Passport ATPN.436234.001-15 PS Location of the label Manufactured and accepted in accordance with mandatory requirements state

NPF SIGMA-IS LB-06 Linear address block (ver 4.52) Operation manual SAKI.425641.004RE SAKI.425641.004 RE

OOO SIGMA-IS LB-06 Linear address block (ver 4.52) Operating manual SAKI.425641.004RE LB-06. Operation manual 1. PURPOSE... 3 2. COMPLETE SET... 3 3. TECHNICAL CHARACTERISTICS...

SWITCHING DEVICE UK-VK UK-VK version 10 UK-VK version 11 UK-VK version 1 UK-VK version 13 UK-VK version 14 UK-VK type 15 1.1 General information 1.1.1 This label

Uninterruptible Power Supply "AKAT" Passport Russia Tver - 1 - UNINTERRUPTIBLE POWER SOURCES AKAT PASSPORT 1. INTRODUCTION This passport is intended for the maintenance personnel to study the operating rules

RECEIVING AND CONTROL DEVICE SECURITY AND FIRE QUARTZ OPTION 1 OPERATING MANUAL UP001 General information 1 18 Thank you for choosing the QUARTZ device manufactured by NPO Siberian ARSENAL. This product

Operating instructions Pulse secondary power supply OPTIMUS-1230-OD Secondary power supply OPTIMUS 1230-OD ARGP.435520.003TU is designed to provide power

CONTROL DEVICE FOR VOICE SIREN "SONATA-K-L" PASSPORT CODE OKPO 43 7242 TU 4372-011-56433581-2005 C-RU.AB03.V.00025

RESERVED SECONDARY POWER SUPPLY BBP-30 V.4 TS

OOO Elektronnye tekhnologii Uninterruptible power supplies BBP-20, BBP-25, BBP-30, BBP-35, BBP-40, BBP-50, BBP-55, BBP-24-3. Passport UNINTERRUPTIBLE POWER SUPPLY PASSPORT 1 INTRODUCTION This Passport

Ministry of Internal Affairs of the Russian Federation Federal State Institution "Research Center "Protection" Novosibirsk branch (NF Research Center "Protection") 43,729 AC voltage stabilizer

RESERVED POWER SUPPLY RIP-12 version 01 (RIP-12-3/17M1) Label АЦДР.436534.001-01 FL 1 BASIC TECHNICAL DATA 1.1 General information 1.1.1 Redundant power supply RIP-12 version 01 (RIP-12-3 /17M1)

Edition 01 RU ISO 9001 A MAXIMUM HEAT FIRE DETECTORS R T RTL-A1 RTL-A2 RTL-A3 RTL-B O MCI PASSPORT 425212.006-06 PS N Chernivtsi, Ukraine 2012

VOICE ALARM UNIT ARIA-BRO-R TU 4372-021-49518441-10, amend.4

ISO "Orion" Voice Annunciation Unit "Rupor" Installation instructions АЦДР.425541.001 IM

DEVICE CONTROL SECURITY - FIRE CONTROL PKOP 0104059-6-1 "Signal VK-6" ATSDR.425513.006 RE Operating manual CONTENTS Introduction 1 1 Description and operation of the product 1 1.1 Purpose of the product 1

VOICE INFORMATION UNIT YANTAR BRO 1. Purpose The voice notification unit YANTAR BRO (hereinafter referred to as the “product”) is designed to operate as part of a voice notification system as a device for generating

Control panel Security and fire QUARTZ version 1 OPERATION MANUAL CONTENTS GENERAL INFORMATION...2 TECHNICAL DATA...3 DEVICE DESIGN...4 INSTALLATION PROCEDURE...5 PREPARATION FOR WORK...5

ISO "Orion" Voice Announcement Unit 01 Installation manual АЦДР.425541.001-01 IM

1 GENERAL INFORMATION Thank you for choosing a device of the "Granit" family, manufactured by NPO "Siberian Arsenal". This product will provide reliable protection of your object from penetration and fire. Control panel device