How to install a stove in a countertop. Do-it-yourself hob installation

I still opted for an induction hob. Because I don’t have gas in the house, but I didn’t want a regular electric one. Panel from the manufacturer HANSA, there will definitely be an article about it, but today is not about that. Today I need to install this hob in the countertop! And I have never done this before, I just saw how the masters do it. But I didn’t really want to pay 2000 - 2500 rubles for installing the surface, and therefore I decided to install it myself, in principle, I succeeded, I think you can too ...

The article will be with pictures, so read and see everything step by step.

Guys for starters. Be sure to read the article, so as not to redo the wiring several times!

1) Tool. To install (insert) the hob, we need a jigsaw, drill, tape measure, pencils for marking and flat board, about 1 meter (I have left of furniture) or a large ruler.

2) Determine the place where we will embed the panel, I have this place above the void for oven. Of course, the panel can also be embedded above cabinets with dishes and kitchen utensils but I don't think it's very correct.

3) We try on the panel by eye. The main thing is to leave enough space around the edges.

4) Now the most difficult thing is to mark the dimensions on the countertop. To begin with, I determined the center, simply measured the distance (where the installation will be made) and marked the center.

5) Now we take a book, it has everything required dimensions you should try to follow them. To begin with, I define the gaps horizontally. That is, what size should be set aside from the wall and which one should be left to the edge of the countertop. Moreover, these dimensions are already indicated by the manufacturer, here they are in the picture - X and X1. X - 50 mm (to the wall), X1 - 60 mm (to the edge). Set aside these dimensions. I have a corner attached, it is 30 mm, so I set aside another 20 mm from it and that 50 mm. At the end, exactly 60 mm remains, you don’t even need to measure there.

6) Now the dimension “A” is important to us - this is the width of the plate, we have it 560 mm, that is, 280 mm from the center (which we set aside). Draw two parallel lines from the center at a distance of 280 mm. And in the end we get all the sizes. Look here.

7) Now we take a drill, insert a drill 8 - 10 mm (to fit a jigsaw file) and drill. We need to drill three to four holes (three are possible, then the last corner in which we do not drill - we will cut to it). Here are my three holes.

8) Next, we take a jigsaw and begin to cut the countertop, everything is strictly in size. It should be noted the dimensions that are in the instructions already with gaps. You will have to sweat the tabletop is difficult to saw, but after 20 - 25 minutes everything was ready.

9) After that, just take out the cut out plate and remove it.

10) We remove the sawdust and try to insert the panel into place, everything should be fine! They did it according to the size of the manufacturer. The plate moves a little, that is, you can move it a little to the right - to the left, as well as up and down.

Hello.

Today we will talk about built-in kitchen appliances.

The vast majority of modern kitchen sets contain a hob in their composition. Therefore, those who want to make kitchens must be able to install it, especially since it is not at all difficult.

So how is it done?

Everything is very simple: you need to take a countertop, cut a niche in it, insert the hob there, and fix it. It seems to be so...

But for the sake of clarity, I suggest that we consider all important points associated with the installation of this technique.

Personally, I advise, if possible, to purchase cooking stoves with plasticine. But, in any case, such a technique is not a sink, which, usually, during installation, is attracted to the countertop with its entire surface.

The hob fixture is located, I don’t even know how to put it correctly, in short, it is located “like a goat”, and no matter what you do, you won’t be able to pull it to the countertop with the whole surface. Therefore, during installation, it is necessary, from the outside, to process the joints with silicone.

Yes, it is better and more convenient to mount this technique when the countertop is already fixed on the lower modules. And plan the set in such a way that the hob is not located close to the sink (well, at least not closer than 250-300 millimeters).

Well, here, it seems, is everything related to the installation hob.

I want to note one more detail: Nothing is perfect anywhere and never happens.

Therefore, if when installing the hob, a small gap has not been removed somewhere, look at the fasteners (maybe it needs to be bent), and if nothing helps, fill the gap with silicone and don’t worry, this is such a technique, not ideal. Not everything here depends on you.

Yes, more. Try to tighten the fasteners once, and then, often, in the cooking holes, the threaded holes for the fasteners are such that if you screw in and unscrew the corresponding bolt a couple of times, the thread is licked, and then in general, you can’t tighten the fasteners with anything ...

Many years ago kitchen sets did not represent the possibility of mounting a hob in them. Today, this is a common phenomenon, which saves space in the kitchen, and also makes cooking more convenient and comfortable. Installing the hob in the countertop can be done independently. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the size of the future opening.

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen sets, which qualitatively affects the interior of the kitchen and its functionality. Inserting the hob does not take much time.

First of all, on the countertop, you need to make a markup that will fit the size of the hob.

Next to each side of the niche, you need to drill a hole, the diameter of each should be from 8 to 10 mm. The next step is to cut out the niche and treat it internally with silicone. The tabletop is installed on the lower level of the headset. The inside of the panel is attached with double-sided tape or a little plasticine. The tabletop is covered with silicone.

Step by step installation:

1. The tabletop is placed on the bottom of the headset. If the walls are uneven, the countertop will need to be trimmed. And if they pass through it gas pipes, for them it is necessary to make special holes. The countertop should be ready for installation down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil outlines that will help you make further markup.
3. The tabletop is laid face down, and markings are made on the reverse side for a future tie-in.
4. In each intended cut, small holes must be made so that you can work with a jigsaw.
5. Carefully cut out the niche with an electric jigsaw.
6. You need to make sure that the tabletop does not deviate under its own weight. In the process of cutting, it is better to carefully support it.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone from the outside. This is done in order to create an additional hydro-barrier, since the fasteners may not be pressed against the countertop enough.

The gas hob must be chosen very responsibly, because it should last for many years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can embed the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

At self installation it is important to prepare everything necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work related to gas is unsafe to carry out. It is best to perform the installation together with a wizard or someone who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

Hose Selection Tips:

• Check hose for damage. There should not be a single defect on the hose.
• The hose must be certified. When buying, you should ask the seller to present all the documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, the calculation of dimensions must be given Special attention. Sometimes in the kit for the hob you can find a template that you need to use in order to properly saw through the countertop. It is important to remember that water should not get on the surface of the panel. gas countertop should be located at a safe distance from furniture and textiles.

How to properly install the hob in the countertop

Built-in electric stove handy device for installation in the kitchen. It works just as efficiently as a stationary stove, but does not take up as much space. Installing such a panel can be quick and easy, without resorting to the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If the master conducts self repair not the first time, then installing the hob will not cause difficulties.

Before installing the panel, you need to properly cut a hole in the countertop. To facilitate the installation work, manufacturers indicate the required dimensions in the instructions for the device. Pre-marking greatly simplifies and speeds up the installation process.

Installation steps:

• On the countertop, you need to make markings that will correspond to the dimensions of the panel.
• Using electric jigsaw, you need to make a cutout in the countertop. To get started, you need to drill a small hole for a jigsaw. The cut will be even if you use a jigsaw file with fine teeth.
• The dimensions of the hob must match the cut hole. Sections must be treated with a sealant or nitro-lacquer. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected, focusing on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to control the activation of the burners and their temperature.

What to look for: fixing the hob to the countertop

The installation process of the hob is simple, but requires careful preparation. First of all, it is tedious to choose the right hob, check its passport data, prepare the tools and decide on the installation location. The installation of a gas and electric hob is practically the same.

You need to mount the panel on the countertop, in which you need to make the appropriate cutout.

It should be noted that in order to install electrical panel You will also need to install an electrical outlet. For a gas panel, care must be taken to carry out gas communication. The built-in panel must be installed so that the maximum gap between it and the worktop is 1-2 mm.

What to look for:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the countertop.
• Cut out the necessary segment in the countertop in order to perform the installation correctly.
• Treat the countertop with special materials that will protect it from the effects of external negative factors.
• Push the panel into the cutout.

It is important to remember that the mortise panel should not enter the gap with force. If there is a backlash, the location of the countertop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the countertop will avoid contamination of the panel.

hob seal

The sealing gasket must be attached to the hob. If the panel is removed after some time of use, you will notice that the seal will be covered in dirt and grease. The gasket needs to be replaced from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass seal. The table and cutout can be pretreated with a transparent sealant. Sealant residues must be wiped off or carefully removed with a spatula.

Benefits of sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

Bosch seals are known for their high quality. Just placing a panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening, and a gap is formed, then the tape and the treatment of the gaps with sealant will help save the situation.

Installing the hob in the countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel qualitatively only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions should be phased and coordinated.

Thinking about self-manufacturing kitchen furniture? Then it's time for you to find out that making it is only half the battle, and the second half of this business is to complete the furniture with all kinds of equipment. These are built-in washing machines and dishwashers, and a sink, and an oven, and, of course, a hob, about which will be discussed in this article. Together with the site okuhne.net, we will deal with the question of how to install the hob with your own hands and how to connect it to the home gas pipeline and electrical wiring.

Mounting the hob photo

Installing the hob: marking the installation site

Markup is perhaps the most milestone works related to the installation of the hob with your own hands, which, oddly enough, has the most nuances. Judge for yourself - the whole appearance kitchens. This is just the case in which an error of one centimeter can be irreparable - you always need to remember the cost of the countertop. Buying a new one is not that cheap. The fact is that the panel itself should fit clearly above the cabinet, and there is practically no margin for width there.

There are two ways to mark the landing hole - you can simply lay it on the tabletop, center it on the eye and circle it with a pencil, or you can go the way of professionals and calculate everything down to the millimeter. Naturally, it is better to choose the second option for resolving the issue, since in this case there is a minimum chance of making a mistake. This is done in the following way.

Now it's up to the small - cut and mount the hob in the hole. We will talk about this further. For those who do not like to read and delve into what is written, we are attaching a video on installing the hob in the countertop.

Installing a gas hob: two ways to cut a hole

The mounting hole for the hob can be cut using three different electric tools Is it a jigsaw, drill or hand milling machine. The most accurate and beautiful cut is obtained when using manual router, but you don’t even have to ask about its presence in the home workshop of a person not associated with construction. Not everyone has a jigsaw either, but at least it is not very expensive, and you can buy it to carry out these works. Well, almost every economic man has a drill. We’ll start with it, but first I’ll warn you about the quality of the hole obtained with the drill - it can be said to be disgusting. Torn edges are quite difficult to seal, but this must be done, and problems will arise in this regard. In principle, they are solvable, but more on that later.

After the hole is ready, without fail it is necessary to perform its waterproofing - if water or even just moisture gets into the end of the countertop, there is a very high probability that the material from which it is made will swell and the countertop will deteriorate. As a rule, the end face of the cutout is treated with silicone. If you cut a hole with a drill, then it will be quite difficult to do it qualitatively - you have to tinker.

Installing an electric hob: mounting and connection

To make it easier to understand how the hob is installed in the hole in the countertop, let's imagine it as a sequence of work - so to speak, in the form of a small, but clear instructions for installing the hob.

Basically, everything. In exactly the same way, an electric hob is mounted. The only exception is the absence of a gas hose in it. There may, of course, be other nuances - for example, if we talk about an oven-dependent hob, here the installation process looks a little different. To begin with, install the oven, and then the panel, which is connected directly to the oven itself.

Basically, everything. Now judge for yourself whether this work is difficult or not. You can deal with it yourself or, perhaps, contact specialists. In general, based on experience, I can say that most people who are wondering how to install the hob with their own hands do this job easily. In fact, it is not complicated, and all that is needed for the successful completion of the case is to clearly observe all the subtleties and nuances.

This step-by-step instruction about how to cut a hole in a chipboard or MDF countertop for a hob with your own hands. When you do, you probably need to know how to cut holes in chipboard or mdf countertops if you're installing a sink or hob. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the contour gas stove using the template or follow the instructions on the product. In most cases, there are certain limitations that you should pay attention to, such as minimum distance from plate to back panel or both sides, to . Use a large L-shaped square to draw a rectangle on your desktop, otherwise the corners will not be square.

To get an accurate hole, you must use a good saw with the right blade. Therefore, the blade must have teeth oriented downwards, otherwise it will split the surface. Drill initial holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob in the countertop

Materials:

• countertop;
• carpenter's pencil;
• insulating tape.

Tools:

1. Protective gloves, goggles;
2. Saw or jigsaw;
3. Roulette, level, square;
4. C-clamps.

• Wear safety goggles when making cuts.
• Choose a blade with fine teeth.

Deadline

• 10 minutes

When installing a gas hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent potential problems..

How to cut a hole in the countertop for the hob

Guide line markings

The first step is to define the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique in which only the recommended hole sizes are indicated. Place the hob on which is located on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the countertop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-shaped square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check if the rectangle is positioned correctly under kitchen cabinet, in which the hood will be built in, and there is enough space around it (according to the manufacturer's instructions).

Installing under-counter pads

To get an accurate result, you must place several spacers under the countertop. However, the tabletop must be level.

You should leave about 5 centimeters free space between cabinets and countertop, otherwise the saw blade may damage them.

Making initial holes for drilling

Use a drill with a special drill bit to create initial holes along the corners. It is very important to align the bits correctly, otherwise you may drill out of the contour.

Tip: Make sure you are using good equipment for drilling with speed control. Set the drill to low speeds and hold the drill with both hands if you want to have good control over it. Repeat the process for each corner of the rectangle.

Passage of the laminated layer

In this image, you should notice that the drill is going through upper layer. Do not apply too much pressure to the drilling equipment or it may slide out of place.

We remove the residues from the process with a vacuum cleaner

Drilling a hole in the countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention, as it is important to make holes exactly in the indicated places.

Starting holes for cutting in the worktop

After drilling the corner pilot holes, cuts must be made along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. In this way, you will help prevent chipping of the edges.

Cutting a hole with a jigsaw in a countertop

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you fix the countertop. Make sure the blade goes exactly along the cut lines.

Tip: Clean up chips that form frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our advice and read the manufacturer's instructions, the hob should slide easily into the hole. However, if the edges aren't quite straight, you can smooth them out with silicone or caulk.

Tip: Use sandpaper to smooth the cutting edges.

Installing the hob in the countertop

After that, you just have to install the hob in the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step by step advice how to cut a hole in the countertop and install the hob with your own hands, we recommend that you read other articles. Don't forget to share our projects with your friends using social media widgets.