Transfer to the toilet from the riser to the side. Transfer toilet to the root: on the minimum and large distance how far can be placed toilet

You will need

• - toilet removal by 45 degrees;
• - Flavor;
• - fan tube;
• - corner taps;
• - fasteners;
• - silicone sealant.

Instruction

Remove all unnecessary objects, furniture, plumbing devices from the room, which can interfere with the work. Collect the elements of the supplying knee - these are two angular removal of 90 ', made from polyvinyl chloride with a diameter of 110 mm, a removal for the toilet 45' with a seal for the output, a segment of the fan tube with a socket, the diameter of which is 110 mm. It can be applied as an extension cable for a transition, which makes it possible to move the toilet more freely. This process is not from the lungs - it is necessary to achieve as a dense connection of pipes as possible.

At the end of the fitting on the discharges, make marks using markers or a simple pencil in the locations of the connection lines. So then it will be easier to collect design. Now the knee disassemble and treat with silicone grease rubber cuffs, which are available in the compounds. Install them to the original place, then collect the discharge design again. Connect it to the release of the toilet, and connect the opposite end to the fan tube, which is part of the rising design.

By completing these actions, proceed to adjust the removal in height. Make sure that the design has a uniform slope from the toilet to the riser with an angle of more than two degrees. In the pedestal of the toilet, there are holes - through them the marker to tick the points in which the toilet will be enshrined after the final transfer to the new place.

Install the drain tank in place. Make sure that it does not rest in the wall. In the marks made on the floor, drill holes in which you will need to insert a dowel. This soils will be strengthened in place. This will end the work on reinstalling the toilet - it will only be left to drive other objects to the room.

Video on the topic

note

Prepare all the necessary tools and materials in advance. Work on the movement of the toilet should be carried out as soon as possible - the smell is far from pleasant. There is nothing good if the work is delayed because of the running shops in search of the desired detail,

Helpful advice

In order for the design as best can be adjusted in size, get sealing gaskets from rubber and from angular taps, and from the skin. It is advisable to achieve accurate coincidence of the end of the knee with the release of the toilet installed at the new location. Also, it is necessary and connected to the fan tube. It is better to achieve it by nomining and adding the connecting elements. When performing such actions, the desired length of the straight line is selected.

Good day! Your problem is quite solved. SNiP allows you to transfer the toilet bowl, but warns that the distance from the plumbing device to the sewering riser should not exceed 1.5 m. The reasons for that two:

1. A great removal provokes excessive vacuum into the pipes. What threatens the owner of the apartment? At least a permanent unpleasant smell of sewage in the apartment and loud bugging sounds emanating from plumbing. The fact is that excessive vacuum on pipes with every wash will "suck out" water from all near standing plumbing devices and disrupt their hydraulic machines, the main function of which is the obstacle to the penetration of unpleasant odors into the room.
2. The longer the sewer pipes, the higher the risk to face clouds. Theoretically uncleanness in any case will be able to get to the riser, but the greater the distance they have to overcome, the higher the chance of their jams in the pipe. In addition, it is important to observe the optimal slope of sewer communications. If the tilt of the pipe is insufficient, the speed of movement of the unclean will be small, which will inevitably lead to the appearance of a blockage. If the bias of the pipeline will be too large, the liquid drains will be dragged too quickly, but solid uncleans will stop and accumulate.

So, to transfer the toilet to some distance from the riser and do not encounter problems with problems, you need to perform three rules:

• The distance from the riser to the plumbing device can not be more than 1.5 m.
• The slope of the pipe with a diameter of 100 mm should be 2 cm per meter. Smaller elements with a diameter of 50 mm are stacked under a slope of 3 cm per meter.
• No straight corners. If, due to any reason it is impossible, you need to put two knees of 45 ° instead of one part 90 °.

In practice, perform the second item is troublesome. This is due to the fact that it is impossible to provide the desired bias. Therefore, most often you have to raise the toilet over the floor and install it on a small podium. This decision is considered optimal because it makes it possible to provide the desired slope of the sewer pipe and at the same time hide all communications. Alternatively, you can raise the floor level that is no less troublesome. In addition, in this case the height of the room will decrease.

To ensure the desired slope of the sewer tube, the toilet can be raised to a low podium

It happens that it is necessary to transfer to the plumbing to more than recommended in the lower distance or for some reason it is impossible to perform the above requirements. Even in this case, you can find a solution to the problem, or rather, two at once. The first is to transfer the sewer riser. It is extremely undesirable to do this, since the procedure is very troublesome and time-consuming. A simpler solution is the installation of special equipment that provides forced sewers. The device will force the system to work in such conditions when the traditional samotane sewage can not function normally.

The optimal solution is the installation of a fecal pump or, as it is also called, Sololift. Equipment is a pump, which is equipped with shredders in the form of blades. The device forcibly pumps uncleanness, the solid waste grinds the blades, after which it pours the resulting mass into the sewer. The device is distinguished by compact sizes and easy enough to install. Moreover, it is not necessary to perform any additional construction work for its installation.

Depending on the capacity of the equipment, it makes it possible to remove wastewater to 100 m horizontally, and vertically by 5-7 m. In addition, if necessary, the pump allows the use of small diameter pipes: 18-40 mm. If you plan to connect to the sewer system also a shower cabin or washing machine, you need to correctly select the model of the saltifet. Most of them are designed to work with cold runoff, the hot will bring the device in order. Therefore, it is worth choosing a device that is designed to work with high temperatures.

Sololift - a compact device that is installed for the toilet

Small nuance: There are models of pumps with special protection, which allows the device to pump hot wastewater. However, this protection is short-lived, its action does not exceed 30 minutes. The constant work with a hot liquid such devices is contraindicated in the same way as conventional mechanisms. Therefore, it is better to choose a heat-resistant device. Thus, the transfer of the toilet is quite possible, choose any way suitable for you.

Most of the redevelopment are implemented in order to increase the comfort of the room and for more convenience. In typical apartments, for example, uncomfortable kitchens can be, bathrooms. Their small area limits the functionality of the room and does not allow you to install additional equipment there.

In the bathroom (bathroom and toilet), plumbing is often carried out to install any other technique on the free space. Often refreshing with the transfer of the toilet. But many owners are asked by the question: "Is the transfer to the redevelopment toilet?".

According to housing legislation, transfer, device and replacement of engineering equipment falls under the concept of reorganization. The reorganization can be part of redevelopment and must be coordinated.

However, we note the following: Replacing the toilet to a similar new on site of the previous toilet and without affecting the device of floors does not require coordination, but the transfer of the toilet to dismantle the flooring requires coordination; Also redevelopment is the installation of the toilet, so this equipment is not marked initially in the technical plans of the BTI.

Floor affecting with such work may require waterproofing - hidden work, according to which the act will be required.

Redevelopment with the transfer of the toilet requires the development of the project.

The toilet transfer must be carried out according to certain rules :

• from the standing of the transfer is possible for a distance of no more than 1.5 m;
• it is not recommended to mount pipes at right angles to avoid blockages;
• it is necessary to take into account the slope of the pipe and, if necessary, install the podium for the toilet or just lift it over the floor level, etc.

The coordination of the transfer of just one to the project on the project will only be necessary if the pipes need to remove the floor when conducting pipes. The dismantled floor in the zone of the bathroom will need waterproofing.

Project redevelopment with toilet transfer:

If you summarize, then the following is:

• installing a new toilet bowl on the site of the old without affecting the flooring is not redevelopment and negotiation is not required;
• transferring to the toilet from one place to another is a reorganization that needs agreed;
• installing the toilet where it is originally not designated on BTI plans - this is a redevelopment requiring coordination;
• if, when transferring, replacing or installing the toilet, a full or partial dismantling of the floor will be carried out and further waterproofing, it will require the preparation of acts of hidden work on waterproofing - this procedure already implies redevelopment or reorganization;
• when transferring, installing or replacing the toilet and other engineering equipment, all valid standards, norms and rules must be observed.

If you are going to repair with one type of work on transferring or toilet device, we recommend contacting us for developing project documentation or redevelopment, if all this is necessary. Also, our highly qualified specialists will advise you on all the questions you are interested in. You will find email and phone number in the "Contacts" section.

In the apartments of a standard type of bathroom most often possesses the most limited territory, it is for this reason the owners account for painstaking to use each free space. As a result, a desire to transfer the toilease to another angle or deploy it is very often. This event is responsible and difficult. In order to work, you can contact the specialists, and you can do it and on your own, the main thing is to figure out how to make a job correctly.

If the toilet is required to be transferred to a distance that will not exceed a 20 cm indicator, then the work will be not complicated. Placement of equipment can be any. The main thing is to know the minimum distance not only with respect to the pipes or wall, but also for the sink. To move the toilet to the left or right, you need to eliminate it in advance from your knees and water pipes. You should start with the removal of the old device. If the old toilet has been installed on cement or special glue, then it will have to face elimination. If you do at least one incorrect action, the toilet can split. Of course, if you plan to install a new device, then caution to do nothing, however, if it is not so, then you need to overlap water and carefully disassembly.

It lies in 3 steps:

1. Eliminate, stand pastries in the space between the sewer sockeleton and the release of the toilet. In order to carry out this job, you can apply a subtle chisel or flat screwdriver.
2. Gently begin to break the toilet. It will appropriate to use a wide chisel to score in different places. You need to repeat this action until the device starts thoroughly swing.
3. We are trying to raise the device. To do this, carefully pull it on yourself and remove the release along the axis. Experts say that if the device does not succumb, it is impossible to apply force, try to dig it even more and only then pull.

The toilet bowl that was installed on the regular fasteners, and is connected to the sewage cable from rubber will be removed much easier. To remove it, you will need to eliminate screws that are the main fastening. After that, I pull the device for yourself and take it out.

If you want after removing the device in working condition, all manipulations should be carried out very carefully.

It is also extremely careful to the fastening putty when removing it. After all the dismantling work was carried out, you can proceed to preparing the installation of the toilet to a new place. Carefully inspect the flexible hose if its length is insufficient or it flows, then you need to replace it with a new one. If everything suits you, we leave it in the old place. How does the toilet bowl look in the corner, how to move it diagonally, lift and put on the podium you can find out the photo, for the training enough one day.

What if there was an unpleasant smell in the apartment? Several advice to the one who wants to get rid of him:

We answer the question: how to raise the toilet higher over the floor

When the question concerns repairs in the bathroom, many are faced with such a problem as a change in the level of output and pipes for the joining of plumbing. It is mainly because the floor level changes and plumbing is rearranged. In any case, the task appears to raise the toilet higher.

In order to cope with the problem of incomprehension of fittings, it is enough to purchase new adapters. If you have a problem with the inconsistency of the pipeline axes, it is better to use flexible hoses or organize new tubes for pipes. It depends on the coincidence of these holes, at what level from the floor will be your toilet.

First you need to choose a place for mounting and install the device on wooden bars to organize a new level.

Make sure that the horizontality is observed, and all axles and drain pipe coincide.

After that, remove the devices to measure the thickness of those linings that you set to create a new level for plumbing.

To replace the toilet cover, the attachments coincide. How to choose and install it, if you read our material:

In order to have an idea of \u200b\u200bhow to make higher, you must think in advance all the subtleties of the base. You can use a tree, but it will not be the best option, as the tree rotates under the influence of condensate. It will be best to use a concrete screed. In this case, screws and dowels will be needed for attachment. At the moment, the fastening of the device to the base for glue is widely widespread.

Is it possible to make a big distance from toilet to riser

In order to expand the available space in the toilet room, many are solved on such a step as the transfer of the toilet from one side to another. Transferring the device to another angle is possible, however, so that it continues to fully function, you need to know some points.

As for the pipeline, it is also nominated by certain requirements that immediately need to take into account.

For instance:

• You can use pipes, the diameter of which is from 50 to 100mm, the most optimal are pipes with a cross section of 100mm;
• The distance from the device to the riser should be a maximum of 1.5 m, if the length is greater, the power of the drain from the barrel is not enough to push the waste and zatore will appear;
• Observe the right slope, it depends on the pipe cross section.

If the slope is underestimated, then a high probability of clogging appears, since the fluid flow is reduced. If the slope on the contrary will be overwhelmed, then the flow rate will be excessive and solid parts will be gather in the pipe, which will subsequently block the movement of water. How to move the toilet to the wall close to the wall, which maximum distance should be from the wall and how far the toilet can be located from the drain, you can learn from the learning video.

Installation of the toilet in the apartment should be carried out qualitatively. Full algorithm of actions and advice of professionals on the next page:

Change the situation: how to deploy a toilet to 90 degrees

Sometimes there are situations when you want to completely change the design of the bathroom and purchase a new toilet, in which case the toilet can be deployed 90 degrees. The work is very simple, the main thing is to know some technical nuances, rules and subtleties.

To carry out the rearrangement of the digestion of pipes to do not necessarily.

Recently, the use of angular taps and corrugated pipes has become popular.

Corrugated pipes are best suited to deploy a toilet in the already established location. If you are not only unfolding the device, but also transfer it to another place, it is more expedient to use the pipes of the required diameter, which are made of plastic. Using such methods, you can easily be able to expand, but also transfer the toilet to the right place. But make sure that the corrugation is not exposed to excessive stretching, as this can lead to a rupture. This method will help not only to turn the device turn, but also rearrange it in the other direction, for example closer to the sink, or, and move it as much as necessary.

How to rearrange the toilet to another place (video)

As you could notice from this article, the transfer of the toilet is not so complicated, of course, if you are convinced of your skills. If you have gathered to do this case for the first time, and are not aware in all subtleties, it is better to turn to those skilled in the art that will not only carefully carry installation, but also organize a gentle dismantling, so the old device will not be damaged and serves a long time.

In standard apartments, the bathroom occupies a small area. The owners of the premises resort to various tricks so that each centimeter of the square can be used with maximum benefit. Therefore, it is not surprising that as a result of the design surveys, it becomes necessary to move the toilet from the riser.

The event is not the lungs. The easiest way to contact the specialists in the plumbing area, which probably know how to transfer the toilet to another place. But for this you have to adapt to their work schedule, change your plans. And maybe even abandon important events. Despite the complexity of the case, you can do on our own. The main thing is to understand the essence of the question and correctly fulfill all the necessary work.

Toilet transfer: Possible risks

At first glance, there is nothing easier, how to move the toilet to another place, consolidate it there and start fully used. But the movement of the plumbing node to the side of the riser provokes the elongation of the sewer pipes suitable to it. What, in turn, becomes the cause of excessive discharge when washing and breaking the hydraulic assembly in other plumbing devices. And this process is always accompanied by bullous sounds and unpleasant sewer smells.

Also, the transfer of the toilet to the riser often becomes the cause of the appearance of blockages. Since the length of transporting pipes increases, automatically extending the path of unclean. Theoretically, with the proper installation of pipes and, regardless of their length, the drains in any case achieve the exit to the total sewer. But, as practice shows, the longer the pipe, the percentage of the probabilities of the blocks above. According to the prescriptions, SNIPA Plumbing must be installed not further than one and a half meters from the riser. Only so you can avoid the above problems.

An important indicator when transferring the toilet to another place - compliance with the slope of sewage pipes. According to the rules, if the diameter of the parts is 100 mm, the slope must be 2 cm for each meter. With a diameter of 50 mm, the slope is 3 or more centimeters for each meter. If these rules do not observe, the speed of transportation of effluents is reduced, and blockages may appear.

Sometimes it is necessary to install a plumbing device for a pedestal or mount the wall-mounted toilet to be installed to comply with pipelines. Both options have a place to be, but for the second it takes another installation of the box on the wall under the installation and concealment of water pipes and sebage pipes. Therefore, the easiest way to use the first option is to install the equipment on the pedestal.

And one more important point. If you want to minimize the probability of blockages, then the transportation sewer channel from the toilet to the riser should be laid in a straight line and not have turns at right angles. In case of the impossibility of such a pad of the pipeline, in the places of sharp bends in 90 0, two angular pipes are installed at 45 0.

How to transfer the toilet: complex and simple ways

Optimization of space in the bathroom requires moving equipment. As part of the rules and without harsh consequences, it can be moved to different distance (within one and a half meters) and turn. Depending on the transfer range, the simple and complex method distinguish.

Easy way

He implies the transfer of the toilet to the side for a slight distance - 15 - 20 cm. To do this, it is necessary to carefully dismantle the old device. Since, if it is planted for glue or solution, and the rehabilitation of the neck of the cement, one careless movement can cause cracks on the toilet. Therefore, breaking water, carefully and carefully:

• we clean the space between the fuvela and the release of the layer of putty using a narrow bit and a durable screwdriver;
• with a small appointment, we try to break the toilet. For which it may be necessary to help a wide chisel - it must be carefully scored in different places under the base of the bowl. We break up to the moment until the equipment becomes free to swing;
• we raise the toilet. Having captured hands for the rim of the device bowls, we first send the effort on yourself, and then also carefully, along the axis of the sewer tube, we try to remove the outlet of it. If the device is stuck, it is not necessary to make great efforts, you can break the toilet. It is better to return to the second paragraph of the instruction, and again split the device.

If your device is installed on a regular fastener and connected to the pipe through a rubber cuff - you are very lucky. Since to dismantle it, it is enough to unscrew the regular mounts to the floor and remove the release, feeding the device on yourself and turning it along the axis of the pipe.

After dismantling the device, you can proceed to the preparation of its installation in a new place. We examine the existing flexible supply on the subject of integrity, if necessary, change it to a new corrugation. The design of the corrugation involves the presence from the two ends of the sealing rubber rings. But in order to avoid the probability of leakage, it is necessary to use silicone sealant. You should also take care of special fasteners, they are steel and equipped with plastic washers. Then proceed to install the device:

• we celebrate the pencil of the fastening site on the floor. Drills holes: if the floor is concrete, we use a drill with a winning spraying, if the tile - we take a special drill of a larger diameter than the fasteners;
• we clean from the dirt, the old layer of cement, dust and other layers, the release of the toilet and socket, dry them with them;
• we apply on one side of the corrugations to the sealing ring silicone sealant, and stretch it into the flue toilet;
• install and fix the device with the help of prepared screws with plastic washers. Carefully tighten;
• to create an additional support, the formed gaps between the floor and the base are labeled cement;
• at the end of the installation, we lubricate the sealing ring on the other side of the corrugations with a sealant, and insert the corrugation into the sewer of the sewer pipe.

Complex option, or how to transfer the toilet to the riser for 30 or more centimeters

If the design project requires the transfer of the toilet to the greater distance than it allows you to make the length of corrugations, then the alteration of sewage is waiting for you. Dismantling and subsequent installation is carried out by the same scheme as in the first version. The differences are to increase the sewer pipeline. Most often for this event, pipes are 110 mm. The length and number of elements, as well as the configuration of the connecting parts directly depends on the new location of the plumbing device. The laying of plastic pipes is carried out either by the floor, or they are mounted on the wall using special clamps.

What should pay attention to?

To lay the sewage in the level of the floor, it is necessary from a tee or crosses to extract the discharge to the toilet. With plastic pipes, everything is simple (everything is easy to remove and cleaned). If the parts are cast-iron, then you will have to resort to the help of a gas burner or a soldering lamp, so that it is possible to destroy the seal and cement smear by heating. After that, you can easily remove the pipe from the termination.

The gasket of the new pipeline is recommended to start from the riser, observing the rules of the slope. The installation of plastic pipes into the cast-iron ignion involves the use of a special cuff-seal. For better sealing, lubricate its joint with silicone glue.

Connecting to a new pipeline is easiest to do with corrugations, providing free access to it to control integrity. Instead of corrugations, you can install a special transition nozzle, which will provide a longer connection.