If you adhere to proper nutrition, then avocados are probably in ...
In the era of new technologies, inconvenient and cumbersome gas and electric stoves comes completely the new kind kitchen equipment. These are cooktops. Such devices harmoniously fit into the design kitchen furniture, convenient to use. Installation hob into the countertop with your own hands - the process is quite simple. If you have even small skills when working with a power tool, such a task is within the reach of a beginner. This can save you money on installation fees.
Choice of hob
These kitchen appliances practically devoid of flaws. All devices can be divided into categories:
- electrical;
- gas;
- combined;
- induction.
According to the material of manufacture:
- stainless;
- ceramic;
- glass;
- enamelled.
In this case, the panel may different number burners and their various arrangement on the surface. At the first stage, you need to choose the most convenient and suitable device. When ordering kitchen furniture, it is necessary to think over the place of installation in the furniture in advance. It is possible that an oven will be installed with the panel. Need to think first about connecting to the network: to gas pipe when choosing a gas panel and to the mains if an electrical device is preferred.
For installation of the electrical network in without fail provide for the cross-section of the power cable and the power of the socket, taking into account the current consumption of the panel and the possible oven specified in the instructions. Do not forget about grounding or protective grounding of metal parts electrical appliance. After preparation, you can get to work.
Do-it-yourself installation of the hob in the countertop is a simple process, accessible to a beginner . First you need to prepare all necessary materials and tools. Inserting the hob into the countertop begins with sizing. Further installation depends on how correctly and accurately the markup is performed. First you need to remove from the panel all the parts that may fall out during installation (these are the protective grill, burners, regulators).
Marking the table top
The dimensions for the technological hole in the countertop can be specified by the manufacturer in the instructions. If not, you will have to take measurements yourself. This is not difficult. To do this, you need to turn the panel over and take its dimensions, given that it should lie on the countertop around the entire perimeter. For convenience, you can make a template by cutting it out of a piece of cardboard according to the respective sizes. Then transfer the dimensions to the countertop using a long ruler, a square, or a prepared template. With maximum precision, to avoid curvature, draw a contour on the table top with a pencil or marker.
Window cutout for panel installation
After making sure that the markup is correct, you can proceed to cut the hole. Using a drill with a diameter greater than the width of the saw blade of the used jigsaw by 2 mm, drill 4 holes inside corners drawn outline. Insert the jigsaw blade into one of the holes and make a cutout in the countertop along the entire contour. To prevent large chips, you need to use a file with fine teeth or a hand mill.
Try on the panel to be installed into the resulting niche, align it. See from the side that everything is done smoothly. If everything is done correctly, proceed to the next the stage of cutting into the countertop. Now process the cut points sandpaper, file, rasp. If the worktop used is made of wood, be sure to exclude the possibility of moisture penetration. To do this, carefully treat the cut point with a moisture-proof material:
- silicone;
- sealant;
- nitrolac.
If the tabletop is made of plastic materials, such processing can be skipped. Plastic will not swell and swell from the presence of moisture. Can be covered in several layers for reliability. After the last layer has dried, glue the cut with a self-adhesive sealant. Preparation completed. You can do the installation.
Installation and connection
Installing the hob in the prepared window is not difficult. To do this, lower the panel into the hole. Using a measuring tool, align its position. After making sure that it is correct, fix it from below with special brackets and self-tapping screws to the countertop. Staples and self-tapping screws are supplied by the manufacturer as a set. It would be useful to use a seal around the perimeter of the installed device. Such a step will also prevent debris and moisture from getting under the surface to be installed. Usually, it comes with the product.
It remains to install in place all the previously removed parts and proceed to connect the energy carrier. If the panel is gas - it must be cut into the gas line. If an electrical one was installed, then it is correct to connect it to a previously prepared electrical network. It remains only to test it in work and use it comfortably. How to properly install the hob, you can see on the video.
The hob allows you to not only cook any dish, but also save space. After all, such equipment has smaller dimensions than large and bulky gas stoves. How to install the hob and oven? Everything is simple. The main thing is to follow the instructions. Everyone is able to cope with such tasks. This does not require expensive equipment, but only the presence of certain tools is important.
What will be required
In conclusion
Now you know how to embed the hob in the countertop with your own hands. Before starting work, it is worth evaluating your skills and abilities. If this is not possible for you, then you should seek the help of professionals. However, it is safe to say that the installation process is not very difficult. Practically everyone can cope with such a task. The main thing is to carefully study the instructions and have everything at hand. necessary tools. When performing such work, it is recommended to take into account all the nuances and subtleties of the process.
Complex cookers for the kitchen, simultaneously combining a hob and an oven, are becoming more and more a thing of the past. Modern housewives less and less used for its intended purpose ovens. They are increasingly turning into a warehouse of pots and pans.
Why overpay money for an unnecessary metal cabinet, when you can buy a comfortable and aesthetic hob, and formed under it free space perfect for storing dishes and other things. Even an inexperienced master can install a hob in a countertop, because its installation does not require experience and qualifications at all.
Varieties of hobs
So, before proceeding with such a procedure as installing a hob into a worktop with your own hands (you can see the photo in this article), you should deal with the varieties of these devices. There are the following main types of hobs:
- Electrical.
- Induction.
- Gas.
It is advisable to entrust the installation and installation of the latter option to a professional, since an incorrect connection can lead to serious problems. When using gas stoves indoors, special requirements must be observed. During installation electrical panels it is also important to observe caution and safety rules when working with high voltage. It is necessary to provide high-quality electrical power with grounding.
When buying a hob, it is important Special attention pay attention to it Since the installation of the hob in the countertop should be carried out with a small margin at the edges. In addition, you need to decide on the location of the tie-in. Spend in advance
Countertop installation
If you have purchased a glass or stone countertop, it is advisable to entrust its installation to professionals. Since you do not know about all the intricacies of the process, you can damage an expensive item. If you can handle the installation yourself, but with some building skills.
You will need the following:
- Grout for tiles.
- Tiles for facing the surface of the countertop.
- Mounting or tile adhesive.
- Tiles with tungsten coating.
- Gun with silicone sealant.
- Electric jigsaw.
- Waterproof wood board.
- A set of tools - a square, a screwdriver, screws.
Replacing the countertop should begin with the dismantling of the old one. Despite the fact that you will not need the old countertop in the future, you must remove it very carefully to avoid damage to the kitchen unit.
It is very important to fit the new countertop to the dimensions of your furniture. It is likely that you will need to cut off the excess. In this case, the unprotected edges of the chipboard are exposed. This material perfectly absorbs moisture, so the saw cuts must be well treated with a sealant. If the countertop is mounted with saw cuts to the stove, it is advisable to close them with special end strips.
Required Tools
Before proceeding to such a process as installing a hob in a countertop (photos show what they are), you need to prepare the following tools:
- Pencil.
- Roulette.
- Jigsaw.
- Drill driver with a drill for wood with a diameter of 8-10 mm.
- Sealant.
Preparatory process
To begin with, you should make sure that there are accessible sockets in the place where the hob will be installed in the worktop. The presence of an outlet, a suitable length of the gas supply hose, gas stove These are two fundamental aspects.
If the wiring is old and there is no certainty that it is reliable, it is recommended to run an independent cable for the stove directly from the meter.
Installing the hob in the countertop
- First you need to make a hole in the countertop. To do this, according to the instructions, an opening is marked. If there is no instruction, then
the full dimension is outlined, while on each side you need to retreat about 5 mm. - Using a drill, a hole is drilled so as not to go beyond the contour boundary. Then we continue to work with a jigsaw. To reduce chipping, it is recommended to take a file with fine teeth. In addition, you can paste over the contour with stationery or masking tape.
- After the drank is completed, you need to paint over or sealant the sawn edges to prevent the countertop from swelling.
- Next, the hob is installed in a 28 mm worktop, fixed and connected to the network.
Panel insertion must be carried out with maximum precision. Otherwise, even an error of 1 cm can ruin the countertop, which is one of the most expensive elements of a kitchen set.
Countertop made of artificial stone
Compared to their counterparts in Chipboard worktop from artificial stone is the most durable. Despite this, the main problem is the installation of the hob in an artificial stone countertop.
In most cases, an artificial stone countertop is ordered with pre-drilled holes for a specific hob. But what if the countertop is already installed, but the hob is not yet? AT this case the most reliable and the best option will give the countertop to qualified specialists who, using a professional tool, will make the necessary hole.
If you still decide to take a chance, then this work can be done using the technology described above, but instead of a jigsaw, you will need to take an angle grinder and a diamond-coated disc designed for cutting concrete.
It is important to remember that self-installation of the hob in the countertop must be well thought out at all stages of installation. Only in this case, less time will be spent on this type of work, and their quality and subsequent result will significantly improve.
Panel connection method: socket or connection block
There are two options for connecting an electric hob to the power supply:
- Through a plug-socket connection;
- Through the terminal block, directly by connecting the panel wires to the power cable.
Both options are valid. The advice is simple, if the panel comes with a plug, then install an outlet. The pins of a standard stove socket can handle 32 amps, and nothing will happen to them unless you turn it off when loaded (stove on).
The connection through the terminal block is more reliable, although not convenient when repairing the panel or replacing it.
How to install the hob in the countertop work steps
- Cut a hole in the countertop according to the template;
- Install the hob in place;
- Do electrical connection panels (machine off);
- Turn on power, check operation.
Note: If the hob does not have a sealing gasket that will ensure a snug fit of the hob to the countertop, coat the edges of the countertop with sealant before installing the hob in a niche.
As a result, the hob should lie firmly on the countertop and be firmly attached to it.
Panel connection
- Now connect the panel to the socket or power wires. These works are done strictly with the power off..
- Turn on the circuit breaker of the "electric stove" group and check the operation of the panel according to the instructions.
- By the way, you need to check the operation of the panel before installing it in a niche, so as not to spoil marketable condition if a replacement is needed.
DIY electric hob. It remains only to open the question of self installation built-in hob in kitchen furniture. I note right away that this work will not be difficult to do with your own hands, without resorting to the help of a master.
Each hob comes with instructions. with pictures, in which there is enough information for installation. But the instructions, as a rule, miss a few important points concerning cutting a hole for a niche, as well as where it is better and how to install electrical outlet for connecting the hob.
Gas and electric hobs are installed in almost the same way, only it is better to entrust the connection of the gas surface to professionals. But if you decide to do everything yourself, then keep in mind that there are different burners for liquefied and natural gas, and after finishing work, check with soapy water for gas leaks.
Installing the hob in the countertop
To install the hob in the countertop, you will need an electric drill and a jigsaw. If there is an electric drill in almost every household, then a jigsaw most often has to be bought.
Consider that with the glass-ceramic surface it is necessary to be very careful not to damage it during installation. So weigh the pros and cons, and if you decide to do everything yourself, act according to our instructions. If the furniture is made to order, then inform the furniture makers about the dimensions for the sink and hob. They will make a cut at the manufacturing stage. This is the most best option. After assembling the kitchen furniture, go straight to the fifth point.
Step-by-step instructions for installing the panel in the countertop:
- Opening the instruction from the kit and look at the size of the niche that needs to be cut in the countertop. If the dimensions are suddenly not indicated or there is no instruction, then it will be necessary to measure inner size seat. Please note that the ideal gap between the hob and the worktop is 1 to 2 millimeters. But some make 5-6 mm each, but at the same time the panel can walk in the process of subsequent use of it.
- We make markings on the tabletop. We draw lines along which we will cut with an electric jigsaw. To do this, you will need a long ruler and a pencil. Often, a panel comes with a cardboard template, which is enough to attach and trace around the contour inside with a pencil. Please note that the countertop would not break - its thickness must be at least 38 millimeters. Same way take into account when marking that is the distance from the edge of the hob to the edges kitchen worktop from all sides and to the walls should be at least 50 mm.
- After finishing marking with a screwdriver or drill, we drill carefully at the corners of our markup. The drill is used with a diameter of 8-10 mm, which would then fit the jigsaw blade into the hole.
- Then take a jigsaw with a fine-toothed blade for wood, insert into drilled holes and cut along the perimeter very carefully and slowly. When working, the jigsaw is pressed tightly against the countertop.
- For protection from moisture and dirt, as well as to avoid the formation of fungus, glue the sealant from the kit on the cuts around the perimeter, and if it is not there, then treat it with silicone or acrylic sealant. Trim off any excess with a sharp knife.
- Now take your time install the panel into the cut hole, if it turned out a little larger, then align it with the front edge of the countertop.
If the panel does not become loose, just do not use force to install it. In this case, it is necessary to get the panel and cut the smallest side by a couple of millimeters. - Remained final stage fixing the hob with special clips from the delivery kit.
They are screwed from the bottom of the tabletop and do not allow the panel to move in the gap between the panel and the tabletop.
Where is the best place to install an outlet for an electric hob
Before installation Do-it-yourself hob, even at the assembly stage, I recommend moving the electrical outlet below the countertop, so that neither the plug nor the socket to connect it would be visible in the kitchen. How to connect the hob read in
