How to glue shoe soles. What kind of glue is better to glue the sole of the shoe The sole on the sneakers peels off

You will need

• - Glue;
• - Acetone;
• - Rags or cotton wool;
• - Press;
• - Sealant (MS polymer), silicone sealant;
• - Porous rubber;
• - Cardboard;
• - Insoles;
• - Rubber outsole;
• - A piece of cotton fabric;
• - Knife and scissors.

Instruction

Repair sole using durable rubber glue - this is the most familiar way to lead. As a rule, this is a temporary measure. If the leading edge of the sole is a little unstuck (“asks for porridge”), clean the surfaces to be glued from dirt and, after drying, treat them with acetone. Usually super glue and "Moment" are used. Epoxy glue (EPD), sealant " crazy hands"and polyurethane agent" Desmokol ".

Use glue according to package instructions. Usually it is applied in a not very thick layer (2-3 mm), kept for 10 minutes and the shoes are strongly squeezed with a load from night to morning. Ideally, this will be done in a shoe workshop using a special press. In the same use improvised means, trying not to deform the shoes. It is ideal to use an “g”-shaped block with an additional load.

If the leaky sole has a honeycomb structure, when worn, voids form in it - the heel falls through, the shoes become thinner in this place. Tear off the insole and carefully clean the honeycomb from dirt, glue residue and torn cardboard. After that, they can be filled with a sealant (for example, MS polymer) and allowed to dry properly. Cut out cardboard templates in the shape of an old insole, soak them with the same agent and glue them on sole, then install new insoles.

Sometimes honeycomb outsole due to a small puncture. In this case, the insole is also disconnected (if it is in order, then this can only be done at the puncture site). Fill the honeycomb silicone sealant, fill them with scraps of porous rubber (micropores) and apply silicone again. Place the insole on top and press firmly until the repaired sole is dry.

To correct sole, cracked across, the conditions are almost impossible. To do this, you need to contact the shoemakers and make rubber ("prevention"). The same should be done for abrasion of the heels and toes.

If you managed to get a thin rubber sole according to your shoe size, try it yourself. Use strong shoe glue. To rubber part glued to the base of or nylon, first weld a precisely cut cotton lining on it with a hot iron. When sticking the rubber outsole on the skin, it is recommended to make a 45-degree edge. However, more reliably repair a fracture or abrasion of shoes can only experienced craftsmen.

Useful advice

If you plan to wear shoes for a long time, take them to the workshop right away and ask them to make polyurethane stickers. Then you will not soon have to think about how to seal the sole. Such prophylaxis is inexpensive, and it is easily replaceable. In winter, stickers will save you from ice. At this time of the year, artisanal methods of repairing shoes are only a short-term measure, as boots and boots quickly fail from frost.

Sources:

• Million useful tips

boots usually used by us only a few times a year, for example, to go fishing or to the forest for mushrooms. But they often leak, because we walk around in them not through Canadian greenery, but through forests and slums. So a dilemma arises - it’s a pity for money to buy boots, and you don’t want to go to a specialized workshop, since repairing boots there can cost, if not more expensive, then on a par with the cost of a new product. In this case, it is more rational to glue boots himself.

Instruction

Carefully cut out a patch from the old rubber along the puncture or cut on the boots requiring repair. Clean the sides to be glued, both on the boot and on the prepared patch, with a large file, and then sandpaper or sandpaper.

Spread with a brush or a piece of foam rubber on both degreased surfaces with a thin layer of glue suitable for working with rubber products. Leave the glue to partially dry for 15-20 minutes. Apply the second layer of glue in the same way through the marked one.

Press the patch to the damaged one, supporting it with the fingers of one hand, and outside with the fingers of the other. Try to do this with maximum effort to ensure optimally strong contact between the parts to be glued. Do not use glued shoes within a day after the manipulations.

Sources:

• how to seal pvc boots in 2018

Many thrifty housewives and landlords are unwilling or unable to afford to give away a significant portion of family budget for repairing several pairs of shoes a year. Of course, there are types of work that cannot be done at home due to the fact that special equipment is required. However, with the help of some simple tricks, you will save a significant part of the budget, and perhaps acquire a new hobby or even a new profession.

Instruction

Remove worn buckles, buttons, straps and bows, as well as sewing threads or staples that have come out with a knife or scissors. Remove the straps in those places where they fasten the buckles when replacing with new ones, completely, and partially.

New straps in shape, color, size and method of processing the edges must match those that were previously. Glue the new straps well, and then attach with a two-row bartack stitch. Attach buttons with a regular needle, at least 5 stitches with a distance between punctures of 4-5 mm.

Changing the “slider” with a zipper is also not difficult. From below, spread the threads under the “zipper” a few centimeters so as to pull out the edge of the fastener, remove the old “slider”, put on a new one, strengthen the end of the fastener with a metal bracket, threads, superglue and carefully, with frequent stitches, sew. The “runner” can be bent a little with pliers and squeezed a little. If you press too hard, then its internal parts will begin to scratch the links of the fastener, and then you will have to replace it completely.

The strength margin of the lock can be significantly increased if the lock and clasp are lubricated, for example, with silicone grease in cylinders. It is best to apply it on a cotton pad and gently wipe only the clasp and lock. After that, it will become easier to fasten and unfasten, it will not freeze, and sand and dirt will not stick to it.

If your shoes have plastic heels and need to be replaced, but suitable color if it is not scratched, then buy spray paint in cans, (car paint is also suitable). Before painting, wash the heels with warm water with a couple of drops of FAIRY. The surface will be degreased (acetone will corrode, so it is better to refrain from using it). Dry the surface of the heel and spray the paint evenly from a distance of 15-20 cm. Balloon car paint Worth it, but it will last a long time. This method is not suitable for leather-covered heels.

Most often, for self-repair of sneakers, shoes, sandals and other shoes, second glue is used. Household adhesives are divided into liquid, contact, reaction and thermal. They allow you to solve almost any problem related to home repair.

contact adhesive

If it is intended to bond non-porous surfaces such as rubber, porcelain, plastic, or items that need to retain their elasticity (soles or straps), it is best to use contact adhesive in tubes or spray form. Unlike liquid glue, contact must be applied to both parts to be glued. In addition, it is necessary to allow the adhesive to dry slightly for 10-15 minutes before joining the surfaces. The glue seizes instantly, but it takes a lot of effort to hold the two parts together. When repairing shoe soles, it is best to use a weight, such as an old iron. In order not to disturb the shape of the shoe, you can lay a layer of thick cardboard between the shoe and oppression.

reaction glue

When it comes to bonding highly loaded, non-porous items or where heat resistance is required, professionals recommend the use of reactive adhesives, also known as instant adhesives. They work instantly as soon as the active ingredient reacts with another component of the adhesive or with a certain element. external environment. When choosing a reaction adhesive, pay attention to the requirements for operating conditions. While air oxidation is sufficient for a conventional one-component adhesive to work, more specialized products may require special environments and factors to effective work. Second glue is suitable for repairing heels, straps, as well as quick repair of soles on leaking winter boots and boots. Under the Moment brand, many varieties of reaction glue are produced, including one specialized for repairing shoes.

hot glue

Universal in everyday life and hot melt, widely used for repair and creativity. It does not need to be dosed or mixed and is solvent free, making it suitable for bonding all materials, including solvent resistant plastics. The glue is heated up to 110°C and applied to the surface with a special gun. With it, you can not only glue the sole or insole, but also fix the detached decorative elements or decorate a pair of shoes with rhinestones, sequins and other embellishments.

Related videos

Even the most expensive and high-quality shoes tend to tear and wear out over time. If the sole has come off in your favorite pair, do not rush to contact the shoemaker or take the shoes to the trash. Most likely, you will be able to solve the problem on your own.

What kind of glue to glue shoes

Today there are many varieties of shoe glue. So you can glue the sole of the shoe using the well-known "Moment", rubber glue, epoxy, nairite, etc. Each type of glue has certain properties that you need to know in order to purchase exactly the glue that you need.

The first thing you need to know is that you should not use the so-called "Super Moment". When it hardens, it becomes very hard, which will contribute to the appearance of cracks and fractures on the sole.

As for the rubber adhesive, it is more suitable for secondary work, such as gluing the insole and pre-fixing the sole. It is not recommended to use it for basic work due to its low adhesive ability.

Strong fastening of the sole will be provided by such types of glue as polyurethane glue and a special compound "EVA (ethyl vinyl acetate)". In favor of the latter, we can say that it does not absorb moisture and remains elastic even after drying. The only difference between them is that "EVA" is not suitable for products made of PVC, while polyurethane adhesive can be used to glue a wide variety of materials together.

Do-it-yourself shoe sole repair

Getting Started self-repair shoe soles, you need to prepare: acetone, a retractable knife, glue, cleaning agent, newspaper, a clean rag, sandpaper and a brush. In order to glue the sole of the shoe, you need to perform the following steps:

1. Wash the sole surface well from the inside and degrease it with acetone or alcohol. For degreasing, you can use 70% alcohol.
2. Wait for complete drying.
3. Thoroughly sand the surfaces to be bonded with medium grit sandpaper.
4. Apply the adhesive, carefully filling all small cracks and depressions with a special spatula, spatula or brush. If necessary, after a while, apply another layer of glue.
5. Connect and press the areas to be glued together (it is the pressing force that is important, and not the duration, as is commonly believed).
6. If necessary, remove excess adhesive that could damage appearance shoes with a cleaning agent.
7. Place a small dumbbell inside the shoe or provide another method of weighting. The main thing is that during the time the glue dries, the selected weighting agents do not leave creases on the shoes.
8. Leave the shoes in this position for a couple of days in a warm, dry room.

I also suggest you watch a video with a pretty detailed description the whole process.

First part:

The second part:

As you can see, the process of gluing the sole is quite simple and does not require special skills and abilities. However, if you doubt that you will be able to glue the sole with your own hands, or if you are afraid of completely ruining your favorite pair, it is better to contact the workshop.

Sooner or later, shoes start to leak, as the sole bursts or cracks. If you want the pair to last for a long time, it is better to take the products to the workshop.

Home methods will help repair shoes only not for a long time. But if you want to fix the products yourself, we offer methods on how to glue the soles of shoes at home.

Before starting work, the sole must be cleaned, dried and degreased. For degreasing, use a special solution, gasoline or acetone. After processing, the product is dried again.

Pick up the load so that the shoes do not deform. A block in the form of the letter G with an additional load is optimal. Keep the product under pressure for at least ten hours.

The adhesive composition is applied with a thickness of up to three mm, then held for ten minutes and only then the parts are glued together. Choose only high-quality and proven glue. Suitable option will be the classic Moment glue, polyurethane or epoxy sealant. In addition, you can use special rubber glue for shoes or shoe glue.

According to experts, the best remedy will become polyurethane adhesive due to strength and elasticity. It provides secure fastening and can repair shoes of any kind. In any case, these are toxic compounds, so ensure safety when working. If the product gets into the nose or eyes, immediately rinse the mucous membranes with running water.

Be careful when working, as the adhesive can damage the material of the product, especially if it is suede boots, leather or patent leather shoes. The glue is quite difficult to wash off. Now let's figure out what to do if the soles of the shoes are cracking.

How to glue the sole

• First method

If the shoes are slightly sticky at the edges, you can repair the products with a suitable adhesive. Clean and dry the products, degrease the surface so that the glue grabs better and ensures a reliable connection. Then you need to apply the composition to the parts and leave for ten minutes, then glue the shoes and press down with a load.

• Second method

To repair a crack in the sole, step back five centimeters from the gap in the direction of the heel and draw a parallel line. The area from the line to the nose is cleaned with sandpaper along with a crack. Then you need to glue the gap with Moment glue and make markings for the holes for the threads.

Remove the insoles from the shoes, take a shoe knife and cut out small holes according to the markup. Then, through the resulting grooves, sew the material with strong threads. From above, each seam is covered with glue and left to dry. Clean the sole again and degrease it, then cover it with micropores and press it with a press.

• Third method

Clean the crack inside and degrease. Cut the edges of the sole at the edges with a depth of one mm and indents of five mm in each direction. Then make a patch of rubber in size with a margin.

A bicycle camera is suitable for making a patch. Clean the material with sandpaper and degrease, completely cover with glue on one side, on the other - leave dry edges of five mm.

Bend the cracked sole so that the hole opens up and apply glue. After it dries slightly, glue the rubber patch into the affected area and straighten it out. Leave it under load. The listed methods will help if the sole on the boots, boots or shoes is cracked.

• Fourth method

You can seal the hole in the sole with silicone adhesive-sealant. You need to glue the products on the inside of the shoe under the insole. Carefully insert open glue into the hole and completely fill the hole with the compound.

Leave the products to dry under the press for the time specified in the instructions for the sealant. Close a large hole with a special horseshoe made of polyurethane and seal it with thick glue. Such a horseshoe can be bought in the shoe department or store.

Methods for gluing summer and winter shoes

For spring and autumn, demi-season and winter shoes, a honeycomb or lattice sole design is often characteristic. If the sole bursts on such products, as well as with prolonged wear, it gradually wears out. Voids form inside, the heel can fail.

To restore such products, you must first remove the rubber that covers these honeycombs. To do this, tear off the insole, carefully clean each hole from dirt, debris, cardboard and glue residues. Then empty honeycombs are filled with small scraps of micropores and filled with silicone sealant.

Restoration is continued when the sealant dries and hardens. Prepare new insoles, impregnate with sealant or glue, glue to the sole of the shoe and press with a load for the time indicated in the instructions for the adhesive.

For summer shoes, sneakers, sneakers and other light shoes, you can buy a separate thin rubber sole and glue the products rubber glue. This method is suitable if the products have flat soles. When gluing rubber onto leather shoes, make a 45 degree hem first.

In order for the rubber to stick firmly and permanently to the polyurethane or nylon base of the shoe, first cut a cotton fabric template to size and weld it to the base with a hot iron. Then glue on the new sole.

After repair, it is important to monitor the shoes and take care of the pair. Wash and dry items regularly. Which shoe cream is better to choose, see.

How to fix sports shoes

If sneakers or sneakers are worn out at the location of the socks, treat the damaged areas with sandpaper and degrease. Take rubber or polyurethane of different thicknesses and cut out the patch. A greater thickness of the material is applied to the site of damage, and a smaller one - to a normal sole.

Treat the patch with sandpaper in the place where it adjoins the damaged area. Then cover the material with glue and press it to the sole of the sneakers or sneakers. Keep under pressure for a day.

If a hole has formed in the sole of a sneaker or sneaker, the edges of the hole must first be cleaned and degreased, then an adhesive must be applied. AT big hole insert a fiberglass mesh (serpyanka).

A crack in the sole of a shoe is not uncommon. This situation is especially unpleasant when the warranty for the product has already ended. And although it will not be possible to carry out high-quality repairs at home, it is possible to partially reanimate shoes. Sometimes repaired shoes or boots can be carried for several more months.

Method 1

To repair a broken sole, prepare:

• shoe knife;

• sandpaper;

• a degreasing agent such as acetone;

• instant glue that sets quickly;

• hook;

• threads.

Repair technology:

1. Clean the surface of the sole with sandpaper.
2. Bend the sole to open up the crack. From there, you will need to remove all the dirt, the remnants of the old factory glue, using a shoe knife.
3. Degrease the fracture site with acetone or gasoline, apply instant glue and press the walls together. Note: shoemakers advise using Desmacol or Nairit glue. To repair the sole, you can also take Moment rubber glue, Crazy Hands epoxy sealant.
4. The crack was sealed, but the repair was not completed. In order for the shoes to be worn, the bursting sole must also be stitched. With a pencil, draw zigzag lines across the entire crack. manual grinder or with a shoe knife, make shallow furrows along the entire marking, about 2.5 mm. Now, using your crochet hook, sew up the break, placing the stitches in the grooves you have made. It is advisable to perform several rows of stitches: it will be more reliable, besides upper layer protect the lower threads from abrasion.

Method 2

For work you will need the following materials:

• shoe knife;

• sandpaper;

• acetone or gasoline;

• a piece of a camera from a bicycle;

• rubber glue.

What should be done:

1. As in the first case, the bursting sole must be cleaned and degreased. With a shoe knife, remove part of the sole: cut off 5 mm along each edge of the crack. Maintain a cutting depth of approximately 1 mm.
2. The next step is to measure the depth of the fault on the sole. Add 15 mm to the resulting value - this will be the width of the strip that needs to be cut out of the camera.
3. Clean the cut strip, degrease it well, apply rubber glue to it. Coat one side completely with glue, on the other, leave 5 mm of the edge of the dry surface.
4. Take the damaged shoes, bend them so as to open the crack as much as possible. Holding in this position and not closing for 10 minutes, glue the damaged area with glue.
5. Bend the prepared strip from the chamber in half and insert it into the crack. Now the sole can be straightened. With pressure, press the edges of the strip protruding from the crack to the surface of the sole. Place your shoes under something heavy for a day.

Method 3

To restore the sole, you will need a soldering iron and a piece of nylon.

1. First of all, remove the dirt from the shoes, clean and degrease the cracked surface.
2. Run a hot soldering iron inside damaged area. The sole material will begin to bubble, become sticky.
3. Next, you will need to rub the melted nylon into the damaged surface. To do this, place a piece of nylon on the bursting place and press it down with a soldering iron. The capron will melt, but you just have to fill the crack with it until it completely disappears.

On a note: to straighten the melted nylon, during operation, use not the hot tip of the soldering iron, but the handle.

Method 4

In winter shoes, a thick bursting sole can be repaired as follows:

1. Clean and dry your shoes well. Clean and degrease the crack itself.
2. On the inside apply a layer of Desmokol glue, hold the product for 10 minutes.
3. Coat the crack again, as usually the material from which the sole is made is porous and easily absorbs various substances. Wait 10 minutes, during which time a glossy film will form on the surface.
4. Heat up the adhesive using a hot air blower from a hair dryer and press firmly on the sides to be glued.

Note: when using Desmokol glue, the quality of gluing depends on the pressure on the surface.

Method 5

Repair of winter shoes with a one-component, rubber-based polyurethane adhesive. You can take the "Monument, PVC" glue. It is also often used to repair PVC boats.

1. Clean and dry the surfaces to be bonded well.
2. Bend the sole and go through the large sandpaper inside the crack, degrease.
3. Spread glue on both sides of the defective area. Wait 15 minutes and apply another layer of adhesive. Note: all the time the glue is applied and dries, the crack should be open.
4. After 5 minutes, straighten the sole, dock the surface to be repaired.
5. Next, to fix the sole, take a round stick, place it along and secure with a string. Lay the shoes on the table with the soles towards you, heat with a hair dryer for 30 minutes. The heating temperature should be 60 °C.

If you repair shoes in the evening, then in the morning you can already go outside in it.

Video

Shoes should be of high quality and good quality. But over time, any, even the most wonderful shoes, tend to wear out or even tear. beloved comfortable shoes to throw away the hand does not rise. A professional repair, as a rule, will cost a pretty penny.

My own shoemaker

Most people in this situation try to repair their shoes or boots. on their own. Sometimes this succeeds, and sometimes it leads to a disastrous result, and the shoes still have to be carried to the shoemaker to eliminate the consequences of inept repairs. So what to do?

Do not be upset and do not rush to throw away your favorite shoes that are "asking for porridge". Many troubles are quite possible to eliminate at home. You just need to get down to business and stock up on suitable materials.

The lion's share of all repairs falls on gluing a leaky pair of shoes. And here, a rash purchase of the wrong type of glue can nullify all efforts. Remember: you need to choose reliable and high-quality glue for shoe repair! And our article, we hope, will help you make the right choice.

What is shoe glue

Modern adhesive compositions are effectively used in the manufacture and repair of shoes. They have practically replaced the classic tools used for repairs earlier - nails and threads. At least 80% of modern footwear products are produced adhesive method using different formulations.

The new generation of adhesives provides effective and reliable bonding, as evidenced by professional reviews. Blanks upper parts shoe products are tightened using polyurethane or polychloroprene agents, compositions from aqueous dispersions of emulsions, polymers, rubber latexes.

What are their main benefits? Firstly, the strength of the joint depends little on the thickness of the parts to be glued. Secondly, the materials treated with this composition differ high strength and reliability. Thirdly, the seams are elastic (that is, not rigid) and have good frost and water resistance.

Glue for shoe repair: which one is better to choose

We list the most popular and popular with the means that exist today. It is difficult to say which is the best glue for shoes, because it all depends on the specific type of work and type of product.

It is with such ill-considered actions (deciding to save on the services of a professional and not having the necessary information), i.e., purchasing a cheap tube of absolutely inappropriate glue, that you can completely ruin the thing. After such a home intervention, the shoemaker will have to tinker to correct the situation. Of course, the master will explain which good glue for shoes you should take, but as they say, a spoon for dinner is expensive.

Therefore, be prepared that in the workshop you will be asked for a repair amount that is much larger than usual. Well, this is the very case when the only thing left to console yourself with is that the miser always pays twice.