Warming and repair of wooden windows (Swedish technology). Varieties, adjustment and installation of loops for plastic windows how to remove the plastic window from the frame

To repair PVC windows, removal of the glass package may be required to carry out the procedure for removing the sash. During the removal of the sash, you can harm the glass, so it is recommended to carry out the operation according to the instructions.

Video: how to remove the window sash yourself

Instructions for removing the sash PVC windows

1. Open the sash while ensuring window loops Free access.

2. Eliminate the spindle from the top loop. What does that require?

• With the help of a solid item, it is necessary to press on the window loops;
• The spindle tip, which will be out of the loop, need to be pulled out with the help of pliers;
• For removal, it is necessary to raise the sash up.

3. The sash must neatly put near the wall so as not to damage the glass pack.

4. To set the sash to the place, make all the manipulations in the reverse order:

• Put on the tree-spindle lower loop;
• Singing the top loop, insert the shaft into place;
• Check the reliability of the loops.

Dismantling of plastic windows with your own hands

In this article, let's talk about the so-called "dismantling with preservation."

That is, we need not just to dismantle the plastic windows, and even at the same time not to damage the windows removable.

We will not specify why it is necessary, we will take it right.

So - dismantling the plastic window, while maintaining.

First prepare the adjacent space: we will remove the standing furniture, carpets, and so on, which can interfere.

What is not cleaned is desirable to cover with a film, from dust.

Remove the sash.

Option One - adjustable loops.

First remove with loops decorative lining. Then you need to disconnect the halves of the upper loop.

To do this, remove the connecting rod by pressing it with a screwdriver

and stretching for the tip of passats.

Then open the sash, holding it and, lifting up, remove from the bottom loop.

Option Second - unregulated loops.

I knock out anything pins from loops, only below, and remove the sash.

Now we need to extract the windows from the windows. To do this, we need a small spatula, preferably with rounded corners.

Remove the strokes. Gently insert the corner of the spatula into the slot between the stroke and the frame, approximately in the middle of the opening, then press the entire front edge of the head.

Pressing down - up (if side, then left-right), squeeze the staple from the landing groove.

Plastic loop for windows: rules of operation and care

So we pass along the entire staple, until we get a gap, sufficient to capture the stapper with your fingers.

Remove the stroke from the landing groove.

We repeat the procedure with the rest.

When removing the latter, top, hold the glass, so that it does not fall on you. Otherwise, you threaten the tram and replacement of the glass package.

Carefully remove the glass out of the frame.

Now we delete the slopes.

If they are overhead, decorative, dismantle them,

if the plaster, you have to sweat ....

A thin chisel (better, of course, the perforator) we begin to carefully calm pieces of plaster, trying not to damage the frame itself.

In order to make it easier to make the process, you can make rugs from the frame next to the frame, or to chop the winning drill a number of holes and start from them.

When the whole frame is free from slopes, remove the windowsill.

As a rule, the window sills are mounted on the mounting foam, so it needs to be dramatically undermine, and then pull out from under the window.

But it happens that the windowsill will be attracted to the frame, through the stroke groove, self-drawing.

If so, then unscrew them.

Now we dismantle the tide, from the street.

Remove the screws, remove the caps with drainage holes and tear off the frame from the frame.

The mounting plates can be simply cut with scissors for metal, and you can remove the dowels and use these plates in the future.

From the inside the frame may be anchor bolts,

you need to unscrew, and the anchor themselves - pull out from the wall.

Now we remove the mounting foam, vaporizolation and we clean the entire gap between the frame and the opening.

Of course, it is more convenient (and safer!) To carry out a dismantling of plastic windows with a partner.

In case you disassemble plastic windows with your own hands without helper, it makes sense to delete wedges last.

If the wedges were not, leave one point of attachment to removal of foam and vaporizolation.

Then the frame will not fall at you at the most unexpected moment.

Well, in the end, we take out the frame from the opening.

If you do everything thought out and neatly, the window can be saved.

I will be grateful if you use the buttons:

Modern windows are structures from polyvinyl chloride (PVC).

They are not at all similar to classic wooden, because the frames inside the hollow, consist of cells. In the context of the PVC window frame looks like a profile belonging to one of three classes: economy, standard, premium.

In the economy class, the partitions between the cells are thin, are frozen, so good in the warm climate. Premium class - expensive at the expense of additional options that are not needed. Hence the conclusion: class-standard windows is optimal option. In any case, experts say so.

The more cameras in the frame profile, the better the window

So arranged metal plastic window

Installation and those and others, in view of their "plasticity", traditionally considered the lot of experts.

In fact, the opposite is. And plastic and metal-plastic windows Installation is much easier than classic wooden. As true consumer goods, they do not require special knowledge. It suffices to learn a number of rules, and the installation of this window will not be a problem. The average size of the PVC window, with the dismantling of the old, professionals set less than an hour. You will spend three to four hours, because you will all the time to check your actions with the instruction described below.

Window design

To understand what we are talking about in the description of the installation process, you need to know what is called each component of the structure.

You need to know the names of the elements of the plastic window

The window consists of:

• Frames.

  This is the basis of the window.

• If the window consists of several parts, the frame is divided into part of the impost - the vertical component. If a window of two parts, an impost one, if from three - two, etc.
• The opening part of the window is called a sash, a fixed - a depth. The double-glazed windows are inserted - two, three or more glass, hermetically bonded among themselves.

  Between the glasses, a foil ribbon is laid, providing tightness. There are double-glazed windows with special properties: with reinforced glass, tinted and energy efficient, which, according to manufacturers, reduces heat loss through windows. There are still double-glazed windows, between the glasses of which inert gas is injected. It also reduces heat loss.

• Double-glazed windows are pressed against the frame with a slim plastic plate. The tightness of the compound is ensured rubber seal (It is usually black).
• On the sash sets shut-off accessories.

  This is a specific set of mechanisms that provide opening and locking. They can be different, as they provide different functionality: opening, opening with ventilation, opening + ventilation + micro.

• To ensure tightness on all parts - frame, impost and sash - rubber seals are installed.

Below on the outdoor side of the frame (the one that is facing the street) is drainage holes that are closed with special caps.

The condensation is excreted through them, formed inside due to the temperature difference on the street and indoors.

Drainage holes

Another window has a drop - the board is outside, reducing the precipitation and the windowsill inside. Side and top parts from the street and premises are close to sleep.

They can also be made of plastic or do on another technology.

How to make a measure plastic window

When ordering windows, you will need six sizes: the height and width of the window, the length and width of the windowsill and the slope. In order to measure everything correctly, you need to determine, with a quarter you have a window opening or without.

Opening with a quarter (fourth) and without

We inspect the opening.

If the outer part of the window is already, opening with a quarter. In this case, we do the measurement by the narrow place: the openings rarely have an ideal geometry, so it will have to measure at several points. Find the most small meaning, add 3 cm to it. Pass as it is.

If the open is smooth, the calculation is different. Measure the width and height. From the measured width, we take 3 cm, from the height - 5 cm.

This will be the height and width of your window. In the width we remove 3 cm, since the clearance is required at least 1.5 cm. On both sides under the mounting foam. In height, we take 5 cm in height, since all the same 1.5 cm are needed on top, and the bottom - 3.5 cm will go to the installation of the windowsill.

The length of the windowsill and the low tide is taken with a margin - by 5-10 cm more width of the window opening. When installing and tump and the windowsill "take off" a little in the adjacent walls, there will go there. In the width of the fetters are standard, so you choose the nearest greater.

On the windowsill, the situation is different. Its width is chosen arbitrarily - at the request of the owner. Someone likes wide - so that you can put something, someone prefers her in the wall. So there is no rules.

When ordering, you will need to specify how many and what parts will be in your window: there is or not there is a deaf, where it is located, how many sashers, with what parties they should open.

You will need to specify the type of accessories (ventilation, micro-taking).

Preparation of opening

If the windows change, the installation of plastic windows begins with the demonstration of the old one. There are no problems usually. Breaking - do not build. After dismantling it is necessary to conduct an audit of the opening: remove everything that can fall off. If there are some protruding parts, they must be removed - with the help of a hammer, bolt or power tools.

When the plane is aligned, it is necessary to remove the entire construction trash. Ideally, it's all, right up to dust, otherwise when installing foam badly "grab" with a wall.

If there are too large potholes or cavities, it is better to smell with cement mortar.

The smaller will be the open easier pass installation. With loose wall material, they can be treated with binding compositions: penetrating bonding primers.

Installation methods

There are two different techniques: with unpacking (disassembling) windows and without it. When unpacking in the frame, the holes are drilled through the holes, they are driven into the wall of anchor. This method is more difficult, but fastening is more reliable.

Anchor bolts put three pieces on each side

When installing without unpacking, metal plates are fixed to the frame outside, and then they are to the walls.

It is natural, faster, but the fastening is unreliable: with significant wind loads, the frame will switch or it will resume.

Installation with unpacking

Installing plastic windows with your own hands begins with measurements. Measure the frame and window opening, make sure they are compatible.

After you can proceed to work:

1 Remove the window sash:

• Close the window (the knob is turned down).
• Remove plastic lining on both hinges. They are approaching a screwdriver.
• On the top loop there is a pin that provides a moving connection. It is in the center and performs a little. We press it up until it is drowned (you can take a metal plate, rubbing it into the pin and slightly knock on the plate). Bottom pin will be promoted.

  Now it can be captured by rake or pliers and pulling down, pull out.

• Holding the sash at the top, open the castle. For this handle put in a horizontal position. Rejoint top A little on yourself, lifting the sash, removing it from the bottom pin.

1. On Glukhar, removing the glass. He keeps at the expense of the headquarters.

   They need to be removed, then the glazing itself will be removed without problems. Shot so:

   • In the slot between the stroke and the frame inserted something narrow and durable. If there is no special tool, it is best to use a small spatula.

     Disassembly start with one of the long sides.

   • The spatula of the corner can gently drive into the gap and gradually move the stroke away from the frame.
   • Without removing the tool, we promote a little along, again moving towards the stroke.
   • So go through the entire length.

     As a result, the stroke is already almost separated, it is simply taken out.

   • With a short side, everything is easier: we subvew the released edge and turn the spatula from the groove. We take for the liberated edge with hand and pull up.

Now you can try to remove the glass. Just carefully: he is heavy. If it does not work, remove another one from the strokes.

Just follow the window stood obliquely and the glass package is not falling out. Now, if necessary, you can independently replace the glass.

The liberated frame on the outer perimeter is accumulated by a special self-adhesive ribbon. Its installation is recommended by GOST. With it the window does not like it.

Where to glue the ribbons when preparing a plastic window to installation

Scheme of the location of the mounting wedges and distances between the fasteners

Check the installation correctness must be constantly

Installing the waterproofing tape under the plastic window

• On the outer part of the window opening, where the tump will be based on the wall, we apply a layer of foam.

  Sometimes, if the height difference is large, there are installed a lining profile. And then they are fixed by Olive. Cut from the size of the sampling we get under the protrusion frame and placed there to frame with self-draws.

How to install a tump and windowsill on a plastic window

• At the bottom edge, the tump is also married.

Fooming low tide below

• By contour, we glue the vapor-permeable heat insulating band - it is also recommended by GOST.
• We throw the opening.

  When plastic windows are installed in summer, the gap between the frame and the window opening is sprayed with water from the spray. This is necessary for better polymerization of foam.

• We use a cylinder with foam, filling the available gaps for 2/3 volumes.

  If the size of the gap is large - more than 2-3 cm - is applied foam into several stages. Between two layers, the time interval is required of 10-15 minutes. When the first layer partially dries it, they are also sprayed with water and apply the second. So repeat before filling the volume by 2/3.

PVC windows can be switched in several stages.

• Without waiting for the full polymerization, the free edge of the heat insulating tape is glued to the window of the window.

  Just note that when using the tape, the slopes will need to make plastic: the plaster and the solution will not be "shaking".

• We collect all parts of the window. There are only left finishing work, And they are not a hindrance.
• Under the windowsill, a vapor insulation tape (GOST recommendations) is also installed in the lower part.

Typical errors when placing the windowsill and pVC slopes windows and their correct installation

• The latter are set or closed.

Installation without unpacking

The main subtleties are described above.

Installation starts from mounting mounting plates. They are two species: P-shaped and linear. It is important to choose the most reliable of thick metal.

Plates set at the same distance as an anchor: 150-250 mm from the edge and not more than 700 mm between average.

We are screwed simply by self-reserves to the profile.

Fastening plate to profile

Only fasten not frame, but plates, and not on an anchor, but on a dowel-nail.

How to remove the door with the loops or window

The hole is drilled, rebuilt the plate, the dowel is inserted, putting the plate to the place twist the dowel. If you take powerful plates, they will hold tightly.

No worse than anchor.

How to remove the wing from the plastic window?

Sometimes when installing a window or repair of a plastic window, it may be necessary to remove the wing from it.

How to remove a plastic window with hinges

For this, without errors, please use our instructions.

Instructions for removing and installing the wing of the PVC window

At the beginning of the process, you must open the wing to make these courses available. In addition, the upper circuit must be released from the spindle rotation shaft.

To make it as soon as possible and faster, follow these recommendations:

• Slide the loop with some solid, before the tip of the rotating shaft slightly comes to the bottom of the upper hinge.
• Raise the shaft shaft with the clips and pull it out.
• Raise the lid (it can be easily removed from the bottom hinge).

In the frame, the sheet is made in the reverse order: place the bottom outline on the spindle, connect the upper skirt and window Rama From PVC and insert the spindle.

If the spindle is very dense, use the hammer.

How to remove the wing of the plastic window yourself

Metal-plastic glass has a very big resource Operation - up to several decades, but nothing can save the window from unforeseen force majeures. What to do if the glass crashed or cracked? Change all the glass? Or will it be enough to change the damaged element?

And how to do it?

Of course, you can call specialists from the company's firm, and do not bother with work. But, the process of dismantling and replacement does not represent a special difficulty. You need a minimum of tools and skills.

So, how to disassemble the plastic window yourself, and what should be known?

Construction of a modern window

To understand how to unmount the glass, you need to have the idea from which parts it consists.

• Frame.

  The basis of the frame is metallic profileplaying the role of the framework of the entire system. All fittings and glass is mounted on the frame.

• Double glass. In the old windows, the design was used on the principle - one frame + one glass. IN modern system It is a package of two and more glasses with a fully sealed space between them.

It consists of such components: glass, remote frames, sealants sealants.

• Furnitura.

  Other the smallest detailswhich provide functioning: handles, locks, loops, headquarters and others.

It is assembled that all these components are modern window system.

Causes of damage to windows

If cracks appeared in the windows, it means there are factors that caused this damage.

1. Violated installation technology.
2. Incorrectly measured the parameters of the window opening.
3. The window was incorrectly transported and stored.
4. Strong pressure when opening and closing the sash.

The first two reasons are interrelated.

Technology of installation of new windows provides for the presence of gaps between the slopes and the frame.

How to remove the pvc window with a loop?

If there are no, then the walls of the walls, create pressure, to the entire window system, which will gradually cause cracking of the glasses.

Transport and storage provide proper position In the absence of temperature changes.

If cracks appeared, then it is necessary to replace damaged items.

Measures of glasses

Before disassembling the plastic window, you need to order a new glass unit, or glass.

You will need their size.

It happens that some manufacturers indicate the parameters on remote planks, then you just need to make an order according to this data.

If nothing is not specified on the windshop itself, then using the roulette, measure the distances between the inner edges of the frame. From the result obtained, 10 mm is taken - tolerance for seals.

According to the detached data, the order is made of new elements.

Replacing glasses and double-glazed

Replacing glass windows in plastic windows is easier than changing individual glasses. The space inside is usually completely hermetically from air access and moisture from the outside.

This is done on several considerations - for poor heat conductivity, and to avoid fogging glass package from within.

If the moisture falls into the inside, then the condensate will settle on the glass.

The algorithm of work is carried out as follows.

If the glasses are damaged on the opening flap, it must be removed.

To do this, on the upper loop at the bottom you need to pull one pin, and it is easy to remove. After that the package of glasses take out.

In the case of a deaf (not open) windows, you need to remove the entire package.

How to remove the stroke from the plastic window? In this process, you use the chisel, if required, you can easily knock on it, and they are easily removed.

At the same time, dismantling starts from the middle part, gradually moving to the ends. Disconnect the initially long staps for windows: left and right, and then short - upper and lower.

How to remove the glass?

It is desirable for this to use special suction cups with handles that repairers usually use. Or neat hands.

If the glass pack is very difficult to remove, then the frame skews during operation occurred. In this case, it will be very difficult to insert and new, since the proportions of the entire window are disturbed!

How to replace the glass? This procedure is best carried out with the use of special gaskets - "bridges", they will ensure a solid fixation of the entire system.

When the package of glasses is installed, it is fixed by the strokes, as follows: the lower, top, and the left right.

If the window is without disorders in the design, the procedure will take no more than 20-30 minutes.

How to disconnect the glass from the glass

Replacing the glass in the plastic window is made at the following order.

The reel windows must be put on a flat horizontal surface, a table or a pair of stools will fit the best.

To do this, you can use the usual stationery knife. It is done in two steps.

1. Initially cut the layer to the remote frame.
2. The second cut is carried out directly between the glass and the frame.

After that, the broken glass is easy to pull out.

At the same time, you should not forget about security, remove the elements of the window and dismantle the glasses need to be carried out in gloves!

Before installing the new glass you need to wipe the surface of the neighboring.

Make it easier than a pure newspaper or melamine sponge.

The new element also needs to wipe, and if necessary, and wash, using the detergent.

On the surface where the installation will be carried out, the remains of the old sealant are cut under a small angle.

New glass is installed on a glasswater washed the side inside. All edges are equal in accuracy to the rest of the package.

The mount is ensured at the expense of double-sided tape at the remote frame.

When the glass is laid and glued, it is sealing by applying a new layer of silicone sealant.

In no case cannot be used acrylic sealing agents, as they are sensitive to humidity.

The new layer is applied by using a special pistol, moving evenly from one edge to another.

After the sealant dry all the ends of the glass package are punctured by the usual scotch.

The updated package is mounted back to the frame.

In principle, the answer to the question of how to remove the glass, out of the plastic window is simple. It is necessary to take a minimum of tools and devices, and the process itself, subject to the technology, will take a maximum of 30 minutes.

Plastic windows are able to serve for several years without any problems. But if any breakdown happens, you can easily remove the plastic window with the loops, without damaging it.

However, before this you need to carefully inspect the loops. If they are damaged and / or they have corrosion, then it is recommended to remove the window very carefully, in order not to break them finally. It is advisable to replace the loops immediately.

In order to remove the sash with the loops, you need to remove the plastic caps that protect the design of the loop and serve decorative element. To get rid of them to get rid of them, you need to pose a knife or dyeing (you can remove without tools). They are easily removed and at the same time they are very difficult to damage, since they are made of high-quality plastic.

It is important to pick up required tools. You will need: screwdriver, knife, tweezers, passatias (most often only need a screwdriver). Dimensions of dumping Select based on the size fasteners. You may need some kind of thorough tool - long stick, scrap. The tool should not be too long and sharp.

Removal process

To remove the plastic window, you need to:

1. First you have to loosen all regulating bolts using a screwdriver of a suitable size. It is not required to remove the bolts from the design. If the bolts rusty or are well sufficient, then rinse the design thoroughly (you can wipe with vinegar). However, the design of some upper loops is completely disassembled.
2. Then you need to pull out the rod. You can do this with passages or turning. Do not be afraid to apply power, as the rod and the design itself are made of durable material and break them problematic. Also that it came out without problems is recommended thoroughly rinse the design (you can wipe with vinegar or alcohol).
3. When the rods are removed from both skeins, you can proceed to removing the window itself. Need to lift the window (it may be necessary to apply additional tools). Do it carefully not to damage plastic or glass.

When the window is removed, then you can start up to more detailed repairs. To replace the loops, they will have to completely remove not only on the top, but also on the bottom, it will also be necessary to make some measurements to choose the loop of the desired size.

Sometimes you have to deal with the problem of removing the plastic window to repair or put something. Even if you are going to use the services of dismantling from some company, it will be useful for you to know how to remove the plastic window simply and with your own hands. This knowledge will not be superfluous, because you can control the process.

Installing the window is carried out with withdrawn sash, Then they are mounted in place. Dismantling occurs in the same way, only in reverse order. This procedure will make the window easier, will protect it from damage if you need to remove the design of the whole, protects you from possible injuries with random opening of the sash.

In order to dismantle the window correctly, you need to know how to remove the leaf from the plastic window . This will require an easy tool kit:

• A hammer.
• Pliers.
• Several screwdrivers.

To free the sash, you will need to open it with the help of the handle, in the upper corner to find a loop. Using the hammer and a small screwdriver or the middle nail, you must pull out the pin on which this loop is held. After the fixing element is removed, it will be possible to raise the design element and remove it.

This procedure is suitable if the window has not yet been established. The challenge how to remove the flap of the plastic window with the loops, more complicated, since the pin can not be knocked out: it will interfere with the window opening. It will be impossible to knock it on top, since there is little space for maneuver in the presence of slopes. You can try to use pliers and pull out this design element by pulling it down. Just to pull out this will not work: you need to press the spindle from above the flat object. A large screwdriver is useful, the chisel, another item of a similar shape, which is capable of fit into the distance between the loop and the slope.

The method of dismantling the glass package

Remove the frame from the plastic window is not as easy as it may seem. The difficulty lies in the fact that it is not possible to get an external slope.
If there is no such possibility, and this element of the design requires repair, you can try to dismantle the frame. Knowledge of how to remove the plastic window can be useful if you are going to stick the stained glass, tint glass, change the glass. This will help to reduce the work performed.

First of all, before starting work from the window, you need to remove the grid to remove the extra elements that are removed, including the lattice, if there are. If the work is carried out on the balcony, you need to clear the place for work. You need to start work with the removal of the strokes holding the glass. These elements are easily pulled out with a screwdriver, and you can find them around the perimeter of glass.

Slide on the extracted headproof numbers. When installing the glass package, they need to be installed on their places, otherwise the glass will rise unevenly and will be badly kept or crashed.

Student needed carefully, the blow is heading toward the glass center. You need to start with elements located vertically. The top is removed last. It is necessary that the glass package someone to hold: he may fall after the last support will lose.

Removing the plastic window is also desirable to produce together. This will greatly facilitate the work, will allow it faster and more careful, without breaking the negligence of glass. After removal of the glass package, you can get to the elements of the window outside, while not to pull out the frame.

Insert glass is needed in reverse order. The first headpail is installed in place, then all the others. The side - the longest, most convenient to put them with the last, otherwise you can bend. You can hammer with a hammer, but it is recommended to use rubber, so as not to break the glass.

Studying

Removal from loops

Knowledge can be useful, how to remove the plastic window from the loops, if, for example, you need to replace or repair the sash or remove it to dismantle the window. To carry out this procedure, it is necessary to free the loops from plastic linings. After that, the sash will need to be opened to provide convenient access to the loop. It is necessary to start removing from the top lining, then go to the bottom.

The top loop disassembles the first. It will be necessary to pull the rod from it with the help of pliers. After that, tilt the sash on yourself, remove it from the bottom loop.

Full dismantle

If it is not enough to simply remove the flap of the plastic window with your own hands, you can try to remove it entirely. If you need that the dismantled window remains intact, it is recommended to hire specialists for this; If the integrity of the glass package does not matter, you can try

Cut through the assembly foam

remove it on your own. The difficulty lies in the fact that in the absence of experience, the installers very often break the window block itself, and its replacement is expensive. There is a risk to drop the design to the street.

To dismantle it will take:

• Remove window sash.
• Split frame.
• Remove it.
• Remove sings.
• Remove the windowsill.

How to remove the plastic window from the loops and how to remove the flap of the plastic window, the reader already knows. With the sawing frame of the case is more complicated. Each propyl is done by a manual saw, it is better to use a metal pylon for this. Note that the work is dusty, there will be a lot of small particles.

Duties will help to easily dismantle the frame, after they are made, the design can be pushed and stretch. Before that, it is necessary to cut the entire mounting foam that holds the window; If the frame is screwed, it is possible to notice this by opening the sash, the mounting is pre-rotated. You can try to get a frame without propilov. It is much more complicated, but there is a chance that the design will remain a whole and come in handy for installation somewhere else.

Are you going to change windows and do not know what preference is preferred? - the best choice, buyers have long appreciated them, read

The need to remove the plate of the plastic window may occur in front of you when dismantling, when you need to remove not only it, but also frame, sings, profile, and generally remove the glass, or when repairing a plastic window. And if you really need remove the flap of the plastic window,you need to do it right - without damaging the design. Otherwise you have to spend money on replacing the sash, buy a new glass windows, maybe even frame, tint or profile. Therefore, familiarize yourself with the recommendations of our specialists, and only then take to work.

Preparatory work

Let's start with the preparation of the front of work. Free the windowsill, removing plants and things. Prepare all the tools - they should be at your hand. And you will come in handy screwdriver and pliers.

Change sash

Turn the window handle to a horizontal position and open the sash. From the top and bottom loop remove the decorative plastic lining.

At the bottom of the top loop, you need to push the screwdriver inserted into it and pull down. Next, with the help of pliers, almost completely pull out the pin from the sleeve, while holding the window sash. After that, lift the sash up and remove it from the bottom loop.

In order to insert the sash back, apply all the same steps in the reverse order. After installing the sash to the place, it is recommended to adjust it.

To replace the broken double-glazed glass package or the improvement of the window structure, it is necessary to remove it from the plastic window. The same operation is carried out with the loss of tightness, low energy saving, full or partial damage.

Preparation for work

The glass is held in the frame of the stroke, in the same way as in old structures. All parts, including plugs and profile, are made of PVC and are located in one plane with glass. With the right analysis immediately take into account the location of the elements in order not to harm the design.

To work, you will need a mounting knife for cutting the sealant layer. Remove the strokes of an acute chisel or suitable in size with a spatula. Screw the chisel to remove the rubber hammer. The loop plugs are pulled out with a screwdriver, you will also need a cross screwdriver to unscrew the accessories and fastening bolts.

How to remove the window

Removal occurs only on strict technology, otherwise the integrity of the glass package can be broken and the repair of the entire structure can be repaired:

• First remove. The mounting foam is cut off with a blade or a knife and a short sharp jerk pull the window sill on themselves, at the end a little directing up.
• The second dismantling step implies removal using a flat screwdriver of decorative plugs. The upper pin is upgraded so that it can be easily taken with pliers and pull without difficulty.
• Then you should remove the glass outflower from the frame. Experts recommend starting the process from a deaf sash. The double-glazed windows from the plastic window is pulled out by the chisel and rubber xy.
• At the last stage, you need to unscrew the fasteners screws. Then sucks mounting foamFilling the slots between the wall and the window design. The Rama itself is twisted with a short jerk and gently removed from the opening.

For reference!

Best of all it is removed in dry weather, since high humidity Window structures are able to see, dismantling is heavier.

How to remove the glass

In addition to dismantling, improvements and repair, situations arise in which it is necessary to remove exactly the glass. Most often with such a situation, the owners of deaf windows without moving flaps are faced. In this case, the most important and responsible stage - the removal of the strokes. Convenient to do this by a narrow rubber spatula:

• It is most convenient to remove him from the opening sash. The sash is removed from the loops - the plugs are first taken rightfully, then the folding sash is removed. It can be installed on a solid surface and pull the strokes.
• Before pulling, experts recommend to mark them. Then, when reverse installation, an error will not be allowed and the window will become smooth. In addition, tightness does not break. Next, the chisel is driven into the gap to pull the strokes from the frame. If there is no chisel, you can use a rubber spatula or knife, but with special accuracy. Wrap you need a rubber hammer. First pull longer, then shorter items.
• Under the strokes, a layer of sealant is usually located - it is neatly removed by a spatula and a knife. When the glass is clean from the insulating material and the aluminum bezel will be shifted, the removal process is considered complete.
• When collecting accessories and windows, it is advisable to sign the parties of the frame and parts - during installation there will be no problems with the tightness of the structure.
• Extraction of glass is possible only when the aluminum frame is visible - carefully lifting it, you can get each glass separately, while removing the sealant connecting all the glasses each time. Working with large designs is better together - so far one removes the strokes, the second supports the glass, insuring it from falling.

When removing the glass it is not necessary to remove the frame. If the frame is sealed and does not require dismantling, it is enough to remove insulating elements and holding the glass profile.

Installation of glass

Before returning the glass to the place or install a new one, you need to make sure that the frame of the pure and on the fold there are no dust and construction garbage. The installation process is somewhat different than the removal. First you need to score horizontal and short strokes, only then - vertical and side.

To do this, the shank is inserted into the special groove frame. The rubber hammer head is driven into the grooves. Then you can insert the glass - first fix the bottom, then the top, and only then on the sides.

For reference!

Instruct glass installation in place better specialists. The process does not require serious knowledge, but re-sealing the design by handicrafts will not work.

Work on replacement broken glass It is necessary to spend only in rubberized gloves. If the glass has a serious crack and glass is replaced, it is better to dismantle a damaged part before dismantling, as it will inevitably fall down during operation.

For independent installation Glass is difficult to create a fully sealed design. Sealants used in double-glazed windows are not sold in building stores. Each company produces them independently for its products.

In double-glazed windows with several cameras, the sealant is located around the perimeter between all the glasses. It is necessary to remove the sealant with a gential and consistently, taking out the glass behind the glass.

The process of dismantling glass can be made independently, just adhere to a strict sequence of actions. In this case, the frame will remain a whole, and the new window will become smooth and tight.

Video

Looking at the roller, you learn how to correctly shoot the double-glazed windows from the plastic window with your own hands.