How to properly cut a hole in the countertop for the hob. Ways to install the hob in the countertop with your own hands

Many years ago, kitchen sets did not represent the possibility of mounting a hob in them. Today, this is a common phenomenon, which saves space in the kitchen, and also makes cooking more convenient and comfortable. Installing the hob in the countertop can be done independently. The main thing is to correctly determine the sequence of actions and follow it. It is very important to correctly determine the size of the future opening.

Modern technologies do not stand still. Today it has become possible to integrate hobs into kitchen sets, which qualitatively affects the interior of the kitchen and its functionality. Inserting the hob does not take much time.

First of all, on the countertop, you need to make a markup that will fit the size of the hob.

Next to each side of the niche, you need to drill a hole, the diameter of each should be from 8 to 10 mm. The next step is to cut out the niche and treat it internally with silicone. The tabletop is installed on the lower level of the headset. The inside of the panel is attached with double-sided tape or a little plasticine. The tabletop is covered with silicone.

Step by step installation:

1. The tabletop is placed on the bottom of the headset. If the walls are uneven, the countertop will need to be trimmed. And if gas pipes pass through it, special holes must be made for them. The countertop should be ready for installation down the kitchen.
2. Inside the box in which the hob will be installed, it is necessary to make markings. To do this, you can simply make pencil outlines that will help you make further markup.
3. The tabletop is laid face down, and markings are made on the reverse side for a future tie-in.
4. In each intended cut, small holes must be made so that you can work with a jigsaw.
5. Carefully cut out the niche with an electric jigsaw.
6. You need to make sure that the tabletop does not deviate under its own weight. In the process of cutting, it is better to carefully support it.

The inside of the cut is treated with silicone. After installing the panel, you can additionally coat it with silicone from the outside. This is done in order to create an additional hydro-barrier, since the fasteners may not be pressed against the countertop enough.

The gas hob must be chosen very responsibly, because it should last for many years. After the choice is made, the panel must be installed so that it is convenient and safe to use. You can embed the panel yourself, but you should not do this if you are not confident in your abilities. In any case, you can contact a specialist for help.

When installing yourself, it is important to prepare everything necessary materials: panel, measuring instruments, pencils, sealant, adjustable wrench, saw, gas winding, steel hose.

All work related to gas is unsafe to carry out. It is best to perform the installation together with a wizard or someone who thoroughly knows the entire installation process. One of the most important stages of installation is the choice of hose.

Hose Selection Tips:

• Check hose for damage. There should not be a single defect on the hose.
• The hose must be certified. When buying, you should ask the seller to present all the documents for the goods.
• The hose can be corrugated metal or rubber.

When installing the panel, the calculation of dimensions must be given Special attention. Sometimes in the kit for the hob you can find a template that you need to use in order to properly saw through the countertop. It is important to remember that water should not get on the surface of the panel. gas countertop should be located at a safe distance from furniture and textiles.

How to install the hob in the countertop

Built-in electric stove handy device for installation in the kitchen. It works just as efficiently as a stationary stove, but does not take up as much space. Installing such a panel can be quick and easy, without resorting to the help of specialists. The surface can be combined with an oven, which will make cooking even more convenient.

If the master conducts self repair not the first time, then installing the hob will not cause difficulties.

Before installing the panel, you need to properly cut a hole in the countertop. To facilitate the installation work, manufacturers indicate required dimensions in the instructions for the device. Pre-marking greatly simplifies and speeds up the installation process.

Installation steps:

• On the countertop, you need to make markings that will correspond to the dimensions of the panel.
• Using an electric jigsaw, you need to make a cutout in the countertop. To get started, you need to drill a small hole for a jigsaw. The cut will be even if you use a jigsaw file with fine teeth.
• The dimensions of the hob must match the cut hole. Sections must be treated with a sealant or nitro-lacquer. Sealing self-adhesive tape can be used for processing.

The electric tabletop is connected, focusing on the diagram. It can be found on the back of the panel. It is important to connect the wires correctly in order to be able to control the activation of the burners and their temperature.

What to look for: fixing the hob to the countertop

The installation process of the hob is simple, but requires careful preparation. First of all, it is tedious to choose the right hob, check its passport data, prepare the tools and decide on the installation location. The installation of a gas and electric hob is practically the same.

You need to mount the panel on the countertop, in which you need to make the appropriate cutout.

It should be noted that in order to install electrical panel need more installation electrical outlet. For a gas panel, care must be taken to carry out gas communication. The built-in panel must be installed so that the maximum gap between it and the worktop is 1-2 mm.

What to look for:

• Correctly measure the dimensions of the panel and transfer them to the cutout in the countertop.
• Cut out the necessary segment in the countertop in order to perform the installation correctly.
• Treat the countertop with special materials that will protect it from the effects of external negative factors.
• Push the panel into the cutout.

It is important to remember that the mortise panel should not enter the gap with force. If there is a backlash, the location of the countertop must be aligned, focusing on the front edge. Fastening the seal over the entire surface of the countertop will avoid contamination of the panel.

hob seal

The sealing gasket must be attached to the hob. If the panel is removed after some time of use, you will notice that the seal will be covered in dirt and grease. The gasket needs to be replaced from time to time.

If there is a gap between the panel and the countertop, then the plate can be fixed in the plane, but this must be done so that debris does not fall into the vertical gap.

You can buy a special tape, or you can use a glass seal. The table and cutout can be pretreated with a transparent sealant. Sealant residues must be wiped off or carefully removed with a spatula.

Benefits of sealing tape:

• Reliability;
• Ease of use;
• Environmental friendliness.

Bosch seals are known for their high quality. Just placing a panel is not enough. It must be protected from moisture, grease and debris. If the panel is installed in a large opening, and a gap is formed, then the tape and the treatment of the gaps with sealant will help save the situation.

Installing the hob in the countertop (video)

The built-in hob is a convenient device that saves space in the kitchen and provides comfortable cooking. The rules for installing the panel are simple, so you can install it yourself. It is possible to embed a panel qualitatively only when the dimensions of the panel are measured correctly. After cutting a hole in the countertop, it must be well treated with sealant to protect the panel from water and dirt. All actions should be phased and coordinated.

To replace the order of bored gas and electric stoves came more compact and functional built-in kitchen furniture hobs and ovens. It is difficult to overestimate their advantages - this is both ease of use, and switching on with one movement of the handle, and the most important advantage is their simple and quick installation hob, elementary simple do-it-yourself.

How to install the hob

The first step in the installation process is to mark the hole into which the hob will be installed. The hole is marked based on the dimensions of the hob and its location on the kitchen desktop. To maintain the rigidity and integrity of the countertop, you do not need to place the hole close to the edges, otherwise the weakened edges may break over time.

Along pre-marked lines with electric jigsaw cut a rectangular hole.

To facilitate the task of how to install the hob, before cutting, it is necessary to drill a small hole in the part to be cut, from which the whole cutting process will begin. You only need to use a new file with fine teeth, sawing will take a little longer, but you will get smooth edges without chipping.

We try on the hob in a freshly cut hole and, if the markup was done correctly, we proceed directly to the installation.

First, you need to stick a sealant on the edges of the hole, which will prevent dirt and water from getting under the panel and quickly ruining the kitchen countertop. The self-adhesive sealant is sold as a set with the hob. There is nothing difficult in this process.

Now, when the seal is glued, we install the panel in the hole. If the hole is a little larger, align the hob relative to the edge of the countertop. It remains the case for the small.

With the help of special clamps, also included in the delivery, we fix the hob. Clamps are installed from the bottom of the tabletop, they seem to wedge the panel between its top and the bottom of the tabletop base.

Well, new and shiny hob installed, to improve the sealing of the gap between the worktop and the hob, you can additionally use sanitary antibacterial silicone. There is only one thing left - to bring gas to it and connect it to the electrical network.

This moment also does not cause much difficulty. Like a gas stove, the hob is connected to the gas pipeline using a flexible hose. The connection is made with a union nut through a paranitic sealing gasket. The nut is tightly crimped and checked for gas leakage with soapy water. The electrical part plugs directly into the socket.

Everything, you can install gas burners and coasters for pots and pans, make the first start. And, if everything works as expected, put the brand new hob into operation. It may be necessary to slightly adapt the hob to the gas used in your area. For this, additional gas nozzles are included in the delivery set. Pulling out the burner at the very bottom of the mounting hole, you can see a small brass nozzle. We unscrew it with a flat wide screwdriver, and in its place we screw in a new one suitable for your gas.

Built-in appliances give the kitchen set an aesthetic appearance, so it is extremely popular among buyers. Electric and gas stoves not only save space in the kitchen, but are also highly functional. But how to install the hob in the countertop? Today we will tell you about it in detail.

Step-by-step instructions for inserting a built-in stove

Installation of a built-in gas or electric stove is carried out in accordance with the instructions. It does not present any particular difficulty, but it requires knowledge of several points that allow you to carry out the whole process not only qualitatively, but also quickly.

Before inserting a slab, it is important to determine it exact dimensions which are indicated in the diagram in the instructions. The length and width of the device are measured with a tape measure along the outer edges, to reduce the likelihood of error, it is recommended to re-measure.

Note! The diagram in the instructions for the technique indicates the minimum indents that must be left from the edges of the countertop. It is not recommended to reduce them, it is only possible to change them upwards, since the very narrow edge of the table may break over time.

In accordance with the dimensions of the purchased gas or electric panel, you need to make markings on the countertop. It is important to apply all lines very carefully, since any inaccuracies and distortions in the future will be impossible to correct. When marking on surfaces of dark shades or with a smooth texture, paper tape can be used to limit them and improve visibility.

After marking, you will need to embed the hob into the countertop:

• Initially, a hole is drilled in the place where the cutout will be made from;
• You can cut with a jigsaw, and to reduce the roughness of the resulting cuts, it is recommended to use a file with small teeth. An alternative option is a hand mill (the corners of the cut are rounded off with a radius cutter, and the resulting edges are additionally ground). In the absence of a jigsaw or router, you can cut the mounting hole using a conventional drill, for this you will need to drill a large number of holes with inside markings;
• Sawdust is removed from work surfaces using a construction or household vacuum cleaner.

Note! So that the cut out piece of the countertop does not damage furniture set a stool or sheets of chipboard should be placed under it.

How to fix the hob to the countertop?

It is important not only correctly, but also to carry out its competent installation. After cutting the hole in the kitchen set, you need to fix the hob to the countertop. First you need to "try on" the equipment in order to make sure that the dimensions of the mounting hole correspond to the dimensions of the equipment.

After grinding, all sections are compacted silicone sealant, which will prevent wetting and swelling of the material, the ingress of dirt and food debris. Along with silicone sealant, a self-adhesive seal can be used, which is fixed on the edge of the cut, and an aluminum tape that protects it from temperature changes.

Idea self installation the hob can be somewhat intimidating. After all, you will have to deal with either electricity or gas and at the same time work with fairly expensive kitchen equipment. However, none of the steps for installing a hob are particularly difficult. It just needs to be done carefully and correct sequence from the very beginning to the end.

Steps

Installing an electric hob

Remove the old hob, if any. If you are replacing an old hob, you will need to remove it first. Turn off the electricity in the distribution box. Remove any attachments from the hob and clean off any sealant. Disconnect the wires, remembering how the old hob was connected, and remove the hob from the hole it sat in.

Make sure you have enough space in the location you have chosen for the hob. Ideally, you should have a gap of 76 cm above the hob, and on the sides of it there should be about 30-60 cm of free space. You should also make sure that there is enough space under the worktop to accommodate your new model hob.

Make sure that there is a junction box near the place you have chosen to connect the hob to the mains. Most electric hobs require a direct connection to the mains via a 220V junction box. If you are replacing a hob, you probably already have a junction box.

Measure the dimensions of the hob and make sure it fits into the old hole. If you are replacing a hob, the countertop should already have a hole, and you just need to make sure it fits the new hob.

Adjust the hole for the hob so that it can fit into it. The hole should be on each side 1.5-2.5 cm smaller than the dimensions of the hob. If you do not already have a hole for the hob, or it is too small, then you will need to cut it along the right size. If the existing hole is too large, then sheets of metal can be screwed on the sides to reduce it.

Remove all removable parts from the hob to make it easier for you to put it back in place. The hob may have removable burners, protective screens and other parts that should be temporarily put aside. You also need to remember to remove all packaging materials from the hob.

Install clamps. They are designed to fix the hob. You should hang them from the top edge of the slot and then screw them on.

Lower the hob into the hole. Lower the new hob into the hole, remembering to put the wires through it first. Press down on the hob until you hear the locking clips click.

Connect the wires of the hob to the mains. Electricity must still be turned off when you do this so as not to get an electric shock. Connect the hob wires to the corresponding wires in the junction box.

Install the previously removed detachable parts on the hob. Replace the burners, protective screens and other removable parts.

Turn on the electricity and check the operation of the hob. Turn on the power supply to the hob to check that everything is working properly.

Open all hotplates for a few minutes. Even though you have turned off the gas, there may still be gas in the hose. Open all burners to release the gas. Don't set it on fire. All the gas will come out in a few minutes.

Disconnect the flexible gas supply hose from the fixed gas line using two wrenches. Take one wrench and install it on the hose nut, and the second wrench on the fixed gas line nut.

Remove all removable parts from the hob. Remove burners, protective screens and other removable parts before moving on. This will make it easier to move the hob.

Remove the clips holding the existing hob in place. Unscrew the clips from the underside of the old hob.

Push the hob from below to lift it up. Remove the hob from the countertop and put it in a safe place. Don't forget that the gas hose is still attached to it.

Disconnect the gas hose from the old hob. If you will be using the old gas hose to connect the new hob, you will need to disconnect it from the old hob. Use two wrenches for this, one on the hob and one on the hose nut.

• To disconnect the hose, turn its nut counterclockwise.

1. Connect the gas hose to the new hob. Use a gas joint sealant by applying it to the threads at the junction of the hose and the hob. Apply sealant generously to the threads, but be careful not to get it inside the hose. Screw the nut with a wrench gas hose to the hob.

   Place the new hob in its place. Carefully lower the hob into the opening so as not to damage any of the connections at the bottom of the hob. Before lowering the hob into the opening, you must lead the gas hose forward into it.

   Connect the gas hose to the fixed gas pipe. Apply sealant to fitting threads gas pipe. Then spin wrench gas hose nut. Be sure to tighten the nut tightly.

   Prepare a soapy solution. Prepare a solution of 1 part dish soap and 1 part water to check for possible gas leaks. Stir the solution thoroughly and then either spray it on the gas connections or apply with a brush. Turn on the gas supply valve by placing it in a position in which its handle indicates the direction of gas supply.

   Turn on the burners and check their operation. If the soapy water test reveals no leaks, try lighting the burners. It may take a few seconds for the gas to come up and ignite, because normal air must first exit the hose.

   Attach the hob mounting brackets to the worktop. When you are sure that the hob is working, attach it with mounting brackets to the countertop. Your hob is now fully installed.

   • Replace the doors and drawers of the cabinet under the hob, as well as all its contents.

Choice of hob

1. Get a hob when you want to have a separate oven and hob. Cooktops are very convenient when they need to be installed on free-standing islands. Also, separate hobs are required when you want to have a built-in oven (which is more convenient than a conventional gas stove with oven).

   Install the hob with a downward draft to avoid installing a bulky hood dome above the hob. If you want to install your hob on a freestanding island and don't want to mount a massive hood over it, get a downdraft hob.

   Choose between electric and gas hob. Traditionally, gas hobs are preferred due to the fact that they provide immediate heat release after the burner is ignited. However, some modern electric hobs can also heat up very quickly.

Thinking about self-manufacturing kitchen furniture? Then it's time for you to find out that making it is only half the battle, and the second half of this business is to complete the furniture with all kinds of equipment. These are built-in washing machines and dishwashers, and a sink, and an oven, and, of course, a hob, about which will be discussed in this article. Together with the site okuhne.net, we will deal with the question of how to install the hob with your own hands and how to connect it to the home gas pipeline and electrical wiring.

Mounting the hob photo

Installing the hob: marking the installation site

Markup is perhaps the most milestone works related to the installation of the hob with your own hands, which, oddly enough, has the most nuances. Judge for yourself - the whole appearance of the kitchen depends on how clearly and accurately you can mark, and then cut a hole for the hob. This is just the case in which an error of one centimeter can be irreparable - you always need to remember the cost of the countertop. Buying a new one is not that cheap. The fact is that the panel itself should fit clearly above the cabinet, and there is practically no margin for width there.

There are two ways to mark the landing hole - you can simply lay it on the tabletop, center it on the eye and circle it with a pencil, or you can go the way of professionals and calculate everything down to the millimeter. Naturally, it is better to choose the second option for resolving the issue, since in this case there is a minimum chance of making a mistake. This is done in the following way.

Now it's up to the small - cut and mount the hob in the hole. We will talk about this further. For those who do not like to read and delve into what is written, we are attaching a video on installing the hob in the countertop.

Installing a gas hob: two ways to cut a hole

The mounting hole for the hob can be cut using three different electric tools Is it a jigsaw, drill or hand milling machine. The most accurate and beautiful cut is obtained when using manual router, but you don’t even have to ask about its presence in the home workshop of a person not associated with construction. Not everyone has a jigsaw either, but at least it is not very expensive, and you can buy it to carry out these works. Well, almost every economic man has a drill. We’ll start with it, but first I’ll warn you about the quality of the hole obtained with the drill - it can be said to be disgusting. Torn edges are quite difficult to seal, but this must be done, and problems will arise in this regard. In principle, they are solvable, but more on that later.

After the hole is ready, without fail it is necessary to waterproof it - if water or even just moisture gets into the end of the countertop, there is a very high probability that the material from which it is made will swell and the countertop will deteriorate. As a rule, the end face of the cutout is treated with silicone. If you cut a hole with a drill, then it will be quite difficult to do it qualitatively - you have to tinker.

Installing an electric hob: mounting and connection

To make it easier to understand how the hob is installed in the hole in the countertop, let's imagine it as a sequence of work - so to speak, in the form of a small, but clear instructions for installing the hob.

Basically, everything. In exactly the same way, an electric hob is mounted. The only exception is the absence of a gas hose in it. There may, of course, be other nuances - for example, if we talk about an oven-dependent hob, here the installation process looks a little different. To begin with, install the oven, and then the panel, which is connected directly to the oven itself.

Basically, everything. Now judge for yourself whether this work is difficult or not. You can deal with it yourself or, perhaps, contact specialists. In general, based on experience, I can say that most people who are wondering how to install the hob with their own hands do this job easily. In fact, it is not complicated, and all that is needed for the successful completion of the case is to clearly observe all the subtleties and nuances.