How not to be confused if the benzokos does not start. Why stalls gasoline trimmer Motocos Huter malfunction and their elimination

Summer days came, and on dumart sites Havaica Motokosy rolls. Everyone is good. This tool is powerful, mobile. With the help of gasoline trimmer and grass you can throw, and from dried bunign to get rid of. However, it happens that the motocos does not start or working with interruptions, without developing complete power. There is no longer before work! As the Forumhouse users say, "twitch the starter handle more than mowing." Why the trimmer does not start, and how to deal with it, disassembled in this article.

The reasons for which a new trimmer will not start

Difficulties with the launch arise not only in the motocos visiting, but also from absolutely new ones. In this situation, the yield is one - to listen to the advice of our experts and take advantage of their practical experience!

Grish Member Forumhouse

- I bought myself a new gasoline trimmer and immediately arose difficulties. Very bad start. If you crush a little, and then turn off the motocos, then you will start it "on the hot" yet a big problemthan "on the cold". What to do with him, I won't do the mind! I do not understand how to properly start this motocos!

The reasons for which the new gasoline trimmer will not start, eliminates the instruction on the plant motocos from the forum, which sounds like this:

1. Enable ignition.
2. Drink fuel with silicone button (primer) located below the carburetor. Pages need to do so much (or a little more), as written in the instructions, usually about 8-10.
3. Close the air damper.
4. Fix the gas lever with a stopper with a stopper on increased turns.
5. Run the starter handle 2-3 times. The engine must "grab".

If the engine "grabbed" and stalled, then you need to translate the air damper to the 1/2 position and try to start the motor again. If the motor got started, then we reset the gas and translate the air damper to the "open" position. Trimmer easily starts. We start work.

By performing the manipulation of the fuel swap, do not be afraid to pour it. If this happened, and "poured a candle", it is not necessary to unscrew it, it is enough to translate the air damper to the "open" position and, holding the full gas, simultaneously scrolling the engine with a starter 2-4 times. After that, you can start the engine and start the grass, without fear that it will stall.

The continuous operation of the benzokos is indicated in the instruction manual of the trimmer. In the middle space, 15-20 minutes, after which it is necessary to drown out the trimmer and give it to cool 3-5 minutes. Also for continuous operation, weather and operating conditions have significant impact. In the heat, when making high grass, bican's thickets, under heavy load trimmer overheats, does not work, it does not work with difficulty after the break.

The reasons for which motocos does not start

Many of the problems with benzotrimers arise due to an incorrectly prepared fuel mixture. In two-stroke engines, lubricant is produced special Oil (Not ordinary motor!) mixed with gasoline. If the oil does not mix with gasoline, the motocos will quickly fail. Oil / gasoline is mixed in the proportion specified in the trimmer instruction. This is usually 1:40 or 1:50.

Sometimes there is a question how much oil and gasoline contains the proportion of 1:50.

Leonidd Member Forumhouse.

The numbers mean the following: one part of the oil is taken on fifty parts of gasoline. Hence: 1000 ml (1 liter of gasoline) We divide by 50, we get 20 ml, that is, 1:50.

In this way, the composition of the fuel mixture (gasoline / oil) can be calculated in any proportions. To add oil into gasoline not "on the eyes", you can take a medical syringe on 20 ml, to dial oil into it and "injected" into the tank for the preparation of the fuel mixture.

For the time of the engine running (this is approximately the operation of the trimmer on 2-3 tanks) the amount of oil can be increased. Mix it with gasoline in a 30: 1 proportion.

Insufficient amount of oil mixed with gasoline leads to enhanced wear of the cylindrophone group. Outly oil in the mixture, though not so fatane, but also harmful. Cocking the piston rings, rapid formation of a car in the combustion chamber, the engine power drop can occur. Silencer mesh screen is locked. Therefore, some users of our site (after the end of the warranty period for the trimmer), it is recommended to solemnly crush the last time and dismantle it.

Gasoline used in motocos - AI 92. The gasoline brand is accurately prescribed in the instruction manual. Do not try to "force" the engine, pouring 95th gasoline into it. This can lead to overheating, unstable and bad work of the trimmer, going out in order.

It is not recommended to leave fuel in the trimmer tank with a long break in operation. The working day is better to finish, fully working out the entire mixture. If this is not done, then, because for the night, gasoline from the engine will evaporate, and the fine filling of the oil will remain, the jets of the carburetor can be closed. This will cause difficulties with the start of the engine the next day.

It is also necessary to comply with the safety technique when storing fuel. Many pour gasoline into a plastic bottle of water. Let's figure it out, would you do so.

Skyns. forumhouse, Moscow.

- In no case can not be kept gasoline in plastic containers from under the water. When the fuel mixture is mixed, the static charge accumulates, you can "catch" the spark.

Therefore, at refills are not allowed to refuel gasoline into plastic canisters, only in metal. Before the fill of gasoline to the metal canister, it is better to put it on the ground, so the static from the case is removed and it will not be "to spoke".

But there are such situations when simple manipulations with the motocos do not help. The engine does not start anyway. In this case, "heavy artillery" goes to move - perform diagnostics of the system of nutrition and ignition, guided by the rule "The motor does not work, if there is nothing to burn or set up."

skol00 Member Forumhouse

- Benzotrimer loves purity. It is necessary to follow the purity of the air filter and fuel. Gasoline bought at the gas station is better to defend 2 days and skip through the simplest filter - a piece of bike matter.

Electrical equipment is checked as follows:

1. Unscrew the candle, osmatilla clearance between the electrodes. To set the correct gap between the electrodes can be a "grandfat" way. Then we take the blade from the razor, break it in half and insert the homemade probe between the electrodes. If the blades come in tight, then the clearance is perfect.
2. We put on the candle the cap of the high-voltage wire and lean the candle to metal surface Engine. Twitch several times starter. If the spark is, it hits one point, then, at least the trimmer and does not start, but the gap is adjusted as it should. If not, the spark is weak or "wandering", then it is necessary to adjust the gap between the electrodes again.

Also in electrical equipment can be broken the ignition coil. That is why the gasoline trimmer will not start or start and working with interruptions, and then it bothers it immediately, or the "hot" will not start at all.

You can check the wellness of the coil in the same way as when checking the spark: unscrew the candle, lean it to the trimmer housing. If there is no sparks when jerking, or it appears in times - you need to change the coil.

skol00 Member Forumhouse

- If everything is in order with the quality of electrical equipment, go to check the carburetor.

Trimmers put vacuum carburetors. When it disassembly, cleaning or flushing you need to be extremely attentive - in no case disassemble the lower part of the carburetor, where the primer is located. Air filter (it is visible, if you remove the protective casing from the carburetor) you need to wash washing agents. Best of all - for washing dishes. After drying, we put it back. Carburetor rinse with pure gasoline and blow all the holes with the pump. The fetter of the benzing is also rinsed, then everything is dry and assemble. Usually after all manipulations, the gasoline trimmer, which worked badly and just, tried to stumble, begins to start like a new one.

A thin cable instead of a fishing line, whether to put it on the motorcycle

This thought comes to almost everyone who had to rip 10 acres, smoking high grass. The idea seems not so bad. The cable is stronger than the fishing line, is not so wear out. However, not all so simple.

Tinn Member Forumhouse

"I put a cable instead of a fishing line, without the possibility of its release, securely fixing the two end of the cable and cutting them with the welding (the drop of the melted metal holds the cable from dissolve). Grass Such a tool "Valit" at times. Swallows the pigs to about the finger thick. Stones are not so afraid of the disk. There is truth, the problem: with wear, pieces of cable threads are laid down, and these twisted wires remain at the place of the bow. If they come on them, a pleasant little.

Braid having a gasoline drive is useful thing For owners of household plots, lawns, and when the trimmer suddenly stalls, work on cleaning the territory from the grass stops. The device itself is quite complex mechanismTherefore, there are many different reasons for his breakdowns. The most often emerging problems contains instruction manual. Know the reasons why the trimmer stalls should be in order to independently perform the repair of the device.

Facilities with gas station related to the fact that this device does not start, as defined are classified by specialists from servicing services. They allocate malfunctions with the following nodes of the mechanism:

• the engine in which can be caught or failing the piston and bearings, crackle carcase;
• the fuel supply system, it is possible to clog the filter or the problem with the carburetor;
• mechanical damage to wires, tubes, hoses;
• ignition chain.

To correctly determine the node where the breakdown occurred, it is necessary to pay attention to the fact that under what circumstances the trimmer stalls.

Pressing gas

If when pressed for gas gas station stops, then the reasons may be the following.

1. The most common option is failure adjustment of the carburetorwhich occurs with significant loads on the drive, after the continuous inaction of the mechanism or when it is used under difficult conditions.
   
2. Fuel valve clogging, which is eliminated by his relaxation, as a result of which gasoline on the system begins to flow normally.
3. Weakening and hanging in the cable carburetor. Also may arise tensile fuel hose Up to its rupture caused by the action of a significant load.
4. Sanding Sapuna (check valve), as a result, it does not come fuel to the tank.

If the problem is related to the carburetor node, then it is possible to recognize it by the appearance of the vibrations of the benzokos. When the hose is bursting or stretching the cable - perform the replacement of these components.

Trimmer carburetor

At high speed

When Spit stalls at high speed, this is due to the following problems:

• clogging or sticking the valve located on the lid of the gas tank;
• the carburetor was deregulated under the action of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air supply;
• the hose designed to fence the fuel crackled or poorly connected.

Carburetor regulateRelying on the operational instructions for the trimmer. To customize it is often enough to loosen the tightening of its housing. If there are problem moments with the circulation of the fuel mixture, then it may gradually enter the carburetor. After it is generated, the engine stalls with large revs.

At idle

At idle turns, the common causes of trimmer stop are the following:

• pollution, incorrect or incorrectly configured carburetor adjustment;
• clogging filter for air;

Air filter replacement motocos

Trimmer air filter

• reducing the revolutions of the gearbox during its heating, which is a consequence of the use of an inappropriate fuel mixture;
• clogging of throttle;

• air entering the system;
• not enough fuel for the operation of the benzokosy.

If a problem is a carburetor, then the technique will stop with the "cold" and "hot" launch.

Immediately after started

The unit can sick immediately after launch, if the carburetor is deregulated or was incorrectly configured - it causes uneven feeding fuel. The result is that the device begins to vibrate clearly. To troubleshoot, the carburetor is reconfigured by acting according to the instructions for the mechanism.

Also the engine stops when occurs valve cloggingfeeding fuel. In such cases, it is just enough to clean it. If the motocos at first earned, but then it was immediately stalled, then it is possible to fuel into the carburetor node with some difficulty. Decide the question helps the attenuation of the valve, which ensures the free circulation of the mixture in the system.

Stop can also be called sleeping air In the presence of mechanical damage to the hose (holes, cracks), producing fuel fence. In this case, the drive should be rotated to drive air bubbles from the system faster.

When heated

Motokos is often stopped when heated. At the same time, it starts, works "with jerks" and gradually stops. This process occurs when gasoline in the carburetor boils Either the valve in it is installed rotary, not a disk type. In the latter case, the item is changed.

It is found that the trimmer is heated if ignition chain wire damaged either coil. So that the device starts to work normally, perform the replacement of parts.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to air seats by the system caused by the presence cracked fuel hoseor challenges with the glands. A carburetor dosing system can also be faulty, while the motocos will stop after opening the damper.

Fuel hose in the carburetor

Everything possible reasons that gas station stalls, and their elimination methods are contained in the following video

There are a lot of reasons for stopping motocos, but the most common problems in the work associated with its carburetor are most often. They may arise in any cases. The most problematic option is when a serious breakdown occurs, and you will need to acquire new details or change the benzokos.

In order for the trimmer to work normally for a long time, it is necessary to strictly follow the requirements of the instruction manual. It is necessary to fill the unit suitable in the composition of the fuel mixture, the device must operate at moderate load.

The best models of trimmers according to buyers in 2018

Trimmer Union BTS-9252L

Trimmer Hammer MTK33LE.

Patriot PT 3555 ES trimmer

Trimmer Huter GGT-800S

Trimmer Intercol KB-25 / 33V

The gasoline trimmer is a surprisingly useful thing with the help of which it is possible to put in order not only a miniature lawn in the backyard at home, but also to twider a lot of lawn. But, like all things in this light, it has a property break. In this article we will try to figure out what to do in cases where the trimmer refuses to work.

Gasoline trimmer is poorly started

So, what to do if the gasoline trimmer is poorly started or not started at all? The most common cause of such a breakdown is low-quality fuel. Remember that, for example, TRIMMERS MAROK "CHTIL" and "HUSKVARNA" are unlikely to start fuel in quality below AI-92. Do not save on a merry, because Repair of details of the cylinder -pricultural group can make a third of the entire cost of spit, and sometimes even half. Also, when preparing the fuel mixture, it is necessary to correctly observe the proportions of combustible and oil, which are always listed in the instructions for the trimmer.

What to do, if high-quality fuel is flooded in a gas tank, there is a spark, and the tool still refuses to start? It is necessary to check the condition of the candle. It is located in the center of the lawn mower. It must be carefully unscrewed and make sure that there is no tax on it. If it is, then carefully clean the candle from Nagara and dry it.

If the benzokos does not start even after the methods proposed above, then you need to try to remove the air filter and run the device without it. If the trimmer did not earn, clean the old filter from dust or buy a new one.

It also happens that the lawn mower works a maximum of 5 minutes, and then stalls and does not start until it cools. In this case, try to open the fuel lid of the benzoglotina - the suction sound will appear. After that, tighten the cover back. If you do this manipulation during the time when the trimmer began to stroke, the turnover will be restored, and it can be continued to work. If the lawn mower has stalled before opening the lid, then you just need to start it as it should be on the instructions.

Trimmer does not start after winter

How to be in such a situation? Do not worry and panic. This is a very common problem that is solved literally for 3-4 minutes. First, if last year's fuel remained in the gas tank, it must be merged. Gasoline loses its octave properties after 2 weeks of downtime. Secondly, to start the benzokos after a long stagnation need a little different way. First you need to open the damper and pump a little fuel mixture into the carburetor, then pull out the handle to the sensation of small resistance. After that, you can start the trimmer.

Trimmer start and stall

If, when trying to start a trimmer, it starts, but immediately stalls, then the air filter can again serve. It is necessary to remove it and check if it is scored by dust. If this is true, then you need to make it a thorough cleaning or buy a new one. Also, the problem may be and in the malfunction of the ignition coil. In this case, the lawn mower is better attributed to the service center.

Carrying out the household plot, summer houses are periodically faced with the fact that the benzokos does not start. There are many reasons for failure tool. For proper diagnosis of the problem, the owner of the utility at the cottage of the unit needs to know the device and the principle of operation of its individual parts.

Since the gasoline trimmer refers to complex devices, before starting work, it is necessary to carefully examine the instruction manual. Very often it is simply ignored, or they meet superficially. As a result, when the instrument stalls or refuses to start, the question arises - "why not benzokos?" A long seasonal break in work, improper storage and improper service of the trimmer, will deliver a lot of hassle to the gift book, to eliminate causes.

Where to start the diagnosis of motocos

If the benzokos does not start or immediately stalls after starting, it is necessary to sequentially check all the main components and aggregates. The audit algorithm is:

• Fuel tank (fuel quality);
• Candle and candle canal;
• Air filter;
• Fuel filter;
• Breather;
• Graduation channel.

These nodes are most often the source of the main problems, which can be eliminated after a thorough inspection.

We check the fuel mixture

Before starting the engine of gasoline braid, check the availability, and the quality of the fuel mixture. Do not save, do not greading and "don't be smart" in this matter. Repair or replacement of the piston group will cost you too expensive (sometimes up to 70% of the cost of a new tool). Prepare the oil-fuel mixture is necessary strictly according to the instructions. Calculate its number from real needs. Excess gasoline remaining after work over time loses its qualities.

We carry out the diagnosis of candles and a candle canal

If the quality of the fuel mixture does not cause doubt, and the benzocos stalls when starting, the cause of the candle can be the reason. Here for repair suit ordinary The candle wrench (probably there is every motorist) and a spare candle.

• Candle unscrewed and wipe;
• Carefully dry it (not worth it);
• Excess fuel in the chamber drain through the candle hole and dried it;
• I clean the old candle from Nagar with the help of the noer or the ladies of the file;
• I exhibit the gap with a distance of 1 mm (you can check any coin);
• We return everything to the place and try to start the trimmer.

Dry the channel you need at least 30-40 minutes. Otherwise, there is a risk re-fill and a new candle.

If the candle is a worker, a nest, where it is completely dry, and the benzokos does not want to start, lubricate the threaded connection with a gasoline. It should be slightly moistened. What a wonderful spark would give a candle, light up in a dry chamber simply nothing.

If the Trimmer engine is still not started, it should be excluded such a reason as the absence of sparks due to the weak contact between the candles and the high-voltage wire. If the connection is high-quality, and there is no sparks, most likely, you "flew" the ignition unit. Here, without a master, it will not be possible to do without it, since the part is not repaired, but is sold by a one-piece node.

Diagnosis of benzokosy filters

Another reason for which the gasoline spit is stifted, an air filter can be. To exclude it, try to remove the filter and start the trimmer without it. If it turns out, then you have to change the air filter to a new one, or at least purge and thoroughly clean the old one.

Do not start a gasoline trimmer due to the contamination of the fuel filter. This is the next stage of our algorithm. Here you check the condition of the filter element and, if necessary, change it new. When replacing, try not to leave the suction nozzle without a filter completely, it is prohibited by any instruction manual. Hurry can result in the repair of the piston engine.

Sapun and Graduation Channel

Often, "delicate" branded models of benzokos do not start and sall due to the contamination of the Sapuna. The main function of this element is the alignment of pressure in the gas tank. When clogged this node, a vacuum is created in the tank that prevents fuel supply. Change the malfunction. You can clean the Sapun. You can use the usual needle to clean.

The normal operation of the brain with internal combustion engines can be violated due to dirt from entering the outlet or clogging of the silencer mesh. There is such a problem on the high-generation models. Solve the question can be traditional cleaning and removing the anti-slip grid.

More complex causes of benzokos refusal

If a step by step algorithm The troubleshooting did not give the result, and your braid still does not start or stalls, it is worth inspecting the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable tool operation. Here you can highlight three main problems:

• Channel clogging or jams. It is cleared by all this with special flushing or blows a powerful jet. compressed air from the compressor. Do not use the needles and wire, so that the passages may be damaged;
• Carburator gasket wear. Exit - replacement of the failed gasket;
• Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it. Watch the testimony: if they do not change - everything is fine, and since the pressure will begin to fall, it means that some part of the carburetor is faulty. You will have to find it and replace the new one.

If everything is in order with the carburetor, then the gasoline trimmer may not be launched due to wear of the piston group. When chipping, scratches or scratches are detected, they should be replaced with a piston or cylinder. Piston rings are subject to mandatory check. A small luf piston when sching the connecting rod testifies that it is time to change the rings. This procedure is best to entrust the service center specialists.

Rules of operation and storage of gas station

So benzocos well started to continue to provide her good conditions Storage and operation:

• while working carefully follow the cooling system, carefully and in time, clean the channels in the housing, as well as the starter ribs;
• if necessary, use solvents, kerosene and other detergents for cleaning;
• do not clean the "hot" tool - let it cool;
• strictly comply with the requirements of the instructions on the mode of operation, otherwise you can overheat the engine;
• if you do not plan to use the gas station in the next month, the fuel mixture is needed to merge, because over time it disintegrates into heavy fractions, which will definitely score the channels of the carburetor;
• after draining the fuel, give the trimmer to work at idle, until it stalls, it will help completely remove the remnants of the working mixture.

Before winter storage Do the following steps:

• fully disassemble the braid, rinse and clean all the details that you can;
• inspect the details for damage, eliminate the skews, impulses, renovation and any other malfunctions if necessary;
• fill a sufficient amount of oil into the gearbox and clean the air filter;
• you can partially disassemble the motor, rinse, blow and wipe all moving parts;
• in order to lubricate the piston, you need to unscrew the candle, raise the starter piston to the extreme dead point, pour out some oil into the candle hole and scroll the crankshaft a couple times;
• if you keep the benzokos not in the house, climb the engine with a wilayer.

Remember, careful compliance with the rules will allow you to forget that the benzokos is bad for several seasons.

Recently, the gasoline trimmer has acquired the status of one of the main tools in the Arsenal of Dachnikov. And it is not surprising, because the motorized braid allows you to quickly bring pricework in order. However, sometimes it happens that trimmer and even cold. In such situations, it is necessary to independently set the cause of the fault. Let us find out what to do if the trimmer does not start. The reasons that most often lead to such trouble will be discussed below.

Number diagnostic strategy

How to start diagnostics of faults if the trimmer does not start? In situations where the tool stalls immediately after starting, it is worth viewing the following assembly nodes:

• tank for fuel;
• spark plug;
• fuel and air filter;
• graduation channel;
• breather.

It was the breakdown of the above locations that most often leads to the fact that the trimmer is poorly started. Let's look at how to eliminate similar troubles.

Checking the fuel mixture

Suppose you do not start trimmer. In this case, the first thing must be checked whether fuel is enough in the tank, as well as assess the quality of the fuel mixture. Filling a motorized unit is necessary exceptionally high-quality gasoline. Use is recommended fuel, the mark of which is not lower than AI-95. The refueling of the trimmer of the fuel of unknown origin, bought not at the filling station, is fraught with the occurrence of frequent failures in the tool. This can cause a breakdown of the cylinder-piston system. Repairs in this case often exceeds the cost of the device itself.

Why does not get the trimmer gasoline? Lead to this may also wrong preparation Fuel mixture, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the Trimmer Operation Manual. Prepare the fuel mixture is extremely recommended in large volumes, that is, for the future. Indeed, with long savings, the determination of the properties of the substance occurs. Therefore, if the trimmer does not start, it is necessary to merge the old fuel and take advantage of the freshly prepared fuel mixture.

Diagnostics of the candle canal

What to do if the fuel mixture used in complete orderBut still the causes of the failure of the mechanism can be carried in excessive moistening of the candle canal. To diagnose and eliminate the problem, you must do the following:

1. Unscrew the candle. Carefully rub it, and then dry.
2. Drop the excess fuel in the chamber through the corresponding candle hole.
3. Clear the old candle, if there is a nagar on its surface. Certain with the task will allow the use of a conventional ladies to the nail file or the navel.
4. When installing an item in place, set a gap of 1 mm. To check the parameter, it is enough to put in the prosperity of any coin.
5. Collect functional block back.
6. Try to start the trimmer.

Perform the drying of the candle canal is recommended at least for half an hour. However, in no case should it be resorted to the calcination of its elements. After all, the heating of the spark plug can lead to its final deterioration. What to do if the maintenance of the function block was performed in accordance with the above recommendations, but the trimmer does not start, the spark is at the same time? In this case, it is worth treating a threaded joint with a gasoline. The latter should not be abundantly soaked with flammable. It should only be slightly moistened. Resort to such actions should be ignition. After all, as far as a strong spark did not give a candle, in an absolutely dry chamber simply will not be ignited.

Even in this case, the trimmer does not start, it is worth assessing the quality of the contact between the high-voltage wire and the candle. In the absence of a spark (if there is a reliable connection between the specified elements), most likely the problem is caused by a breakdown of the ignition block. In this situation, you will have to contact the services of the masters that will reinstall the node.

Check filters

Another common reason, due to which the trimmer does not start, is the presence of a blockage in the field of the filter. To confirm your guess, it is enough to dismiss the specified block and try to start the unit without it. If the trimmer engine starts, most likely, it will have to replace the air filter or at least to perform a thorough blowing of the old one. If there are plentiful pollution on the surface of the filter element, you must use a new grid. Resorting to such actions, should not be left completely without a filter suction nozzle. After all, hurry B. this case It may lead to the need to repair the entire piston group of the unit of the aggregate.

Cleaning Sapuna

Often, the engine of branded models of trimmers stalls as a result of clogging of the Sapuna. The main task of the specified component is the leveling of pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the flow of fuel. Eliminate the malfunction allows the cleaning of a sapuna using a conventional sewing needle.

Diagnostics of graduation channel

The stable functioning of the trimmer can be impaired as a result of the layering of dirt in the outlet or the formation of a blockage on the silencer grid. Such a problem most often occurs during the operation of the models of trimmers of the older generation. The issue of dismantling the anti-slip grid and its cleaning is solved.

How to prevent the occurrence of sudden breakdowns during the operation of the trimmer?

So that the unit has always been in a functional state, it is worth following a few simple rules:

1. Conduct timely, regular technical inspection of the main mechanical nodes of the device.
2. Filling the trimmer exclusively fresh fuel, the quality and origin of which is no doubt.
3. Check after each use of the tool, whether oxides and tarts were formed on the surface of the ignition system elements.
4. Avoid the strong load of the trimmer during the work.

So that the unit remains in a working condition, it is necessary to properly prepare it for storage in winter. First of all, you should completely disassemble the tool, after which it is washing and cleaning the components of the elements. It is also important to inspect the functional blocks for damage, with the need to eliminate the deformation of the parts, all sorts of silent, the impulse of the materials.

Placing a storage trimmer, you should fill the gearbox with enough oil. Then you need to clean the air filter, partially disassemble, purge and rinse can be used the engine of the unit. When drying all the mechanisms, you should lubricate moving elements. To process the piston system with oils, it is necessary to pre-extract the ignition candle. Then you need to move the piston in the extreme position, after which the insignificant amount of oil into the candle hole and make the crankshaft scrolling. If you store the gasoline trimmer in the offseason, it is planned not in the house, it is recommended to clean the engine of the aggregate engine with a wilayer. This will avoid the development of corrosion on the surface of important nodes of the mechanism.

Finally

As we see, there are a number of reasons why a gasoline trimmer may not start. However, with a serious approach to the task, the fault specified in the material is quite simply eliminated by their own hands. To seek help from specialists is only in the case of critical breakdowns. Ultimately should always correlate the cost independent repair With the price of the aggregate service in the workshop.