Once upon a time there was an old man and an old woman, they had a daughter, Alyonushka, and a son, Ivanushka. An old man...
Every private developer inevitably faces the question of how to spend the most cheap construction at home, but without losing the quality of finished housing. The lion's share of the costs is the purchase of materials, the cost of which depends not only on its characteristics, but also on the time of purchase.
The time to start work is spring, during the season it will be possible to build a house under the roof without too much haste, and by winter to start heating and carry out finishing work. In order to fully implement the whole process, it is advisable to engage in rational spending of financial resources in advance.
The construction of a cheap house is based on the savings that can be foreseen when buying building materials.
According to research agencies, the most common low-rise stone construction, which uses concrete in blocks, concrete in fixed formwork made of polystyrene foam
- cheap construction of a house with your own hands begins with the purchase of sand, gravel mass (OPGS), crushed stone - it is this “set” that will be needed to start work;
- building a house is cheaper if the purchase is made in late autumn / early winter. Do not postpone this process until the spring. At this time, vehicles cannot enter the quarry, due to the deplorable state of the roads, and later they are completely closed for the passage of trucks. This is a reason for a significant increase in prices for bulk materials, if they can be found at all in the required quantity. Similar trends are observed from year to year;
- in winter period you can buy gas blocks, bricks, FBS blocks, reinforced concrete slabs, fittings, insulation. This is rational if there is a place for their storage. For example, block materials should be on a rise, on pallets, covered with a water-repellent material (p / e film), similarly - a slotted brick. Can be stored without covering solid brick and reinforced concrete products, with the exception of slabs. It is the plates that should be placed on a site with dense soil. A beam or thick logs are placed under the edges, although it is optimal to use foundation pillows or blocks. The material is stacked in piles of 6-8 pieces through wooden spacers.
Why is it rational to purchase the most best material for building a house in winter:
- a significant reduction in prices, factories provide significant discounts;
- there is a tendency to reduce the cost of delivery;
- out of season, it is possible to solve a number of related issues without additional costs, - delivery on an hourly schedule, full loading of vehicles at different plants, etc .;
- delivery time is reduced. In summer, material can be expected up to 4 weeks, in winter - 2-3 days;
- costs for the operation of a truck crane are reduced (up to 15%). This savings translates into a round sum when you consider the number of work shifts. Attempts to conduct "mounting from wheels" in summer period in practice, they exclude the possibility of cheap construction of a private house - this leads to an increase in the cost of work;
- in cold weather, it is easy to provide access for trucks to the site. Hiring for 3-5 tr. bulldozer, clearing the unloading area from snow and providing passage through the frozen hard ground, you can bear minimum costs. In the summer, you will have to pull out every truck stuck at a crossroads, paying for downtime, breakdowns, and hiring additional equipment. In some cases, you have to wait for good weather for delivery, which is already very disadvantageous for the short Russian summer.
The reduction in the cost of construction can be affected by the order of one team, which will install the walls, finish, that is, implement all the work on a turnkey basis
Cheap building materials for building a house - recommendations
If it is necessary to provide the cheapest construction of a house with your own hands, do not prematurely buy cement. Otherwise, you can lose all the material, as it rapidly loses its properties and characteristics during storage. The cost of finishing materials practically does not depend on seasonal fluctuations, therefore, they can not be purchased in advance.
What is the cheapest way to build a house? - from materials from domestic manufacturers. To date, they are practically not inferior to foreign analogues in terms of quality characteristics, but at a cost much cheaper. The overall cost reduction reaches 40%.
Additional tricks on how to reduce the cost of building a house boil down to the following:
- for the purchase, it is advisable to choose a warehouse with a wide range or major supplier with whom you can negotiate wholesale prices. If you purchase materials only there, they are usually met;
- living in the provinces, it is advisable to get out to the district or regional center. Savings on such purchases, even with travel costs, reach 45%;
- at the stage of conducting finishing works it is recommended to visit large hypermarkets more often that sell goods for building houses - promotions, it will not be difficult to buy cheap material at a discount, especially for certain items.
Even with the implementation of the cheapest technology for building a house, without a rational purchase of building materials, it is impossible to ensure construction savings. Regular supply is no less important after weather conditions factor that influences the course of work.
Long summer terms deliveries, potential disruptions, are the source of construction slowdowns, disruptions, loss of working spirit. Thus, you can get a significant increase in total costs and stop all manipulations, that is, there is no need to talk about the cheapest option for building a house.
If you need to get two-storey house, cheaper to build an attic than full second floor
Cheap construction technologies
It is equally important to consider what is more profitable to build a house from, how to do it and what is the cheapest material for building a house. Technology also affects the level financial costs. The minimum cost for building a box can be obtained by choosing frame construction at home; price is easy to calculate. On average, it will be 15 tr / m². This includes cheap construction of houses from timber, wooden bricks.
A monolith on a removable or fixed formwork will cost a little more - from 18 tr. For the construction of a house made of aerated concrete, the price starts from 20 tr per square. The most expensive is brick.
What is the cheapest house to build? Simple square or rectangular boxes much more economical than a complex architecture with open terraces, porch, etc. For example, in terms of the cost of work, such terraces do not differ from the object itself.
To carry out the cheapest construction of a house, but without losing performance characteristics, it should be understood that initial stage it is necessary to lay down three effective components: a high-quality project, albeit a typical one; selection of professional assistants or an entire team; choice of materials.
The cheapest construction of a house should not be carried out on the principle of false economy. Do not exclude geological surveys. The cost of such work will not exceed 30 tr, but the risk of construction disruption without such data is high. If you save at the beginning, you will have to pay more later. The cost of building a house will increase exponentially.
Construction of cheap country houses - what area is preferable?
When building a house, the cheapest, most affordable projects involve building a typical one-story building with a little usable area. There is no universal formula here - you should rely on your own tastes and preferences. However, with less expensive construction as such, the cost square meter such a building will be higher.
With each additional m², the cost of construction increases houses with their own hands, the most cheap option cannot be foreseen. However, the price per square meter is reduced. Eventually it is more profitable to build a house with an attic in two floors of 100 m² than a one-story one of the same area. The rise in price is affected by the angle of the roof and its design features.
Experts say the smart approach is to finished house turned out to be about double more expensive than the site(excluding interior decoration)
Choice of wall material
What is the cheapest and best way to build a house? To understand whether it is possible to save on a particular material, rationally choose a project and calculate an estimate. This information is enough to make a decision.
When choosing a cheap material for building a house, you need to rely on the type of object - whether it will be housing for permanent or seasonal residence, a simple garden or country house where you can rest or a strong, capital building. Practice shows that the economical construction of houses with your own hands (the cheapest option) is provided by concrete - block, monolithic. For the construction of a house, the price starts from 1.2 million rubles.
An interesting version of the cheapest materials for building a house is shown in the video:
Complex deliveries from construction warehouse-shop Material-Stroy(base in Moscow) and wholesale sales of building and finishing materials with delivery directly from manufacturing plants.
Wholesale of materials for construction and repair
? building materials stores
? wholesale depots
? construction markets
? developers
? companies for the repair and decoration of apartments and offices or construction teams
? private buyers (wholesale for certain Construction Materials depending on sales volume)
Terms of wholesale trade in building materials
You can buy building materials in bulk in Moscow and the Moscow region (shipment to the regions of Russia is possible) at the construction and wholesale base of Material-Stroy under the following conditions
Order one-time building materials one item from one manufacturer in the amount of at least 10 tons (for some materials - 7 tons). For example, wholesale Knauf: drywall, dry mixes, Knauf Rotband, etc. Or form a complex supply of building materials of one brand, a multiple of 20 tons.
1558990800: 1559250000:Padlock MGD 75; Cutting wheel for metal 125x1.0x22; Blades for a knife 18 mm (set of 10 pieces); Signal tape 70*200m; Marker Profi lacquer. Munhwa blue; Polypropylene bag GREEN 95x55cm. (50 kg); Knife construction in a case "ONYX"; Knife technical 18mm reinforced "ONYX"; Foam gun cleaner (0.5l); Goggles; All-weather mounting foam Standard (0.75) "SOUDAL" ; Gloves doused with "nitrile" blue; Cotton gloves with PVC 4 threads Ivanovo; Gun for installation. Foam "ONYX"; Respirator U-2K (foam rubber); Roulette 5m x 25mm (rubber) "ONYX"; Roulette 7.5m x 25mm (rubber) "ONYX"; Rezgin boots r.43/277; Rezgin boots r.44/285; Cord - mooring 2mm (100m); Spatula ШП 95 "Delta"; Spatula ШП 200 "Delta"; Facade spatula 450mm "Cote d'Azur"; Brush mop 270mm wood without black; Brush mop 500mm (HARD PILE) wide without black; Electric holder ED-500A; Ground terminal 300 A; Desk Etude T20.2 (beech, 1200x700x750 mm); Rolling cabinet Budget 2556 with three drawers (French walnut, 398x406x521 mm); SPECIAL LADY JACKET WITH ZIPPER art.101-0254-04 size 104-108 height 158-164; PANTS LADY SPECIAL art.101-0253-01 size 104-108 height 158-164; Nail by concrete X-S 47 P8; cartridge DX 6.8/11. M10 BULK yellow; Low shoes Toff Lady Sparta art.120-0055-02 size 37 Vostok Service for Chordova O.P at
St. Petersburg
Tender subject: Padlock MGD 75; Cutting wheel for metal 125x1.0x22; Blades for a knife 18 mm (set of 10 pieces); Signal tape 70*200m; Marker Profi lacquer. Munhwa blue; Polypropylene bag GREEN 95x55cm. (50 kg); Knife construction in a case "ONYX"; Knife technical 18mm reinforced "ONYX"; Foam gun cleaner (0.5l); Goggles; All-weather mounting foam Standard (0.75) "SOUDAL" ; Gloves doused with "nitrile" blue; Cotton gloves with PVC 4 threads Ivanovo; Gun for installation. Foam "ONYX"; Respirator U-2K (foam rubber); Roulette 5m x 25mm (rubber) "ONYX"; Roulette 7.5m x 25mm (rubber) "ONYX"; Rezgin boots r.43/277; Rezgin boots r.44/285; Cord - mooring 2mm (100m); Spatula ШП 95 "Delta"; Spatula ШП 200 "Delta"; Facade spatula 450mm "Cote d'Azur"; Brush mop 270mm wood without black; Brush mop 500mm (HARD PILE) wide without black; Electric holder ED-500A; Ground terminal 300 A; Desk Etude T20.2 (beech, 1200x700x750 mm); Rolling cabinet Budget 2556 with three drawers (French walnut, 398x406x521 mm); SPECIAL LADY JACKET WITH ZIPPER art.101-0254-04 size 104-108 height 158-164; PANTS LADY SPECIAL art.101-0253-01 size 104-108 height 158-164; Nail on concrete Х-С 47 Р8; cartridge DX 6.8/11. M10 BULK yellow; Low shoes Toff Lady Sparta art.120-0055-02 size 37 Vostok Service for Chordova O.P. Price: not specified.
Get accredited for Electronic Platform. Obtaining accreditation is a simple and free procedure, but takes about one business day.
If necessary, take training in working with auctions on the Electronic Platform.
Make sure that all documents required for bidding are up to date.
If necessary, prepare the documents and information provided for in paragraphs 1, 3 - 5, 7 and 8 of part 2 of article 62, parts 3 and 5 of article 66 of 44-FZ.
Select the method of providing security for the bid. Take advantage of our solutions.
Have you applied for the auction?
Wait for notification of admission to bidding! At this stage, the first parts of applications are considered.
Are you allowed to trade?
Congratulations! Plan your participation in the auction.
The organizer of the auction rejected your application and you do not agree with this decision?
Auction! Whoever offers the most wins. profitable terms and price.
In the event that within 10 minutes from the beginning of the auction none of the participants has submitted any price proposals, such an auction is recognized as failed.
If the price offered by the winner of the auction is 25% less than the Initial Maximum Price (IMP), such participant is obliged to confirm his reputation and provide security in a larger amount.
If the winner of the auction evades the conclusion of the contract, information about this is sent to the Register of Unfair Suppliers (RNP).
Wait for the results of the auction, track the deadlines:
Within 30 minutes after the end of the auction - the publication of the Protocol of the Electronic Auction (EPEA) on the Electronic Platform.
No more than 3 working days from the date of publication of the Protocol of the Electronic Auction (EPEA) on the Electronic Platform - consideration by the Customer of 2 parts of applications, as well as the formation of the Protocol of Summing Up the Results (SAP).
Not later than the working day following the date of signing the Minutes of Summing Up (PIP) - placement by the customer of the PIP on the Electronic Platform and in the Unified Information System(EIS)
Are you a winner? Congratulations! Provide the Customer with the performance security and sign the contract
The signing of the contract is possible no earlier than 10 days from the date of publication of the Minutes of Summing Up (PIP) in the Unified Information System (UIS).
Strictly follow the deadlines. The ratio of working days and days off is not important:
Not more than 5 days from the date of publication of the Minutes of Summing Up (PPI) in the Unified Information System (UIS) - the Customer publishes the draft contract.
Not more than 5 days from the date of publication by the Customer of the draft contract - the Winner publishes the protocol/draft contract. The winner who did not send the protocol of disagreements or did not send the signed draft contract after 13 days from the date of publication of the Protocol of Summing Up the Results (SIP) in the Unified Information System (UIS) is recognized as having evaded signing the contract.
The ratio of working days and days off is fundamental:
Not more than 3 working days from the date of publication by the winner in the Unified Information System (EIS) of the protocol of disagreements, the Customer publishes the finalized draft contract (or in a separate document the refusal to fully or completely take into account the comments in the protocol of disagreements of the winner).
No more than 3 working days from the date of publication by the Customer in the Unified Information System (EIS) of the finalized draft contract - the winner publishes the protocol / draft contract + provides confirmation of the contract performance.
StroyTorgi ETP is the first service in Russia that specializes in organizing auctions exclusively in the construction industry.
The platform brings together sellers and buyers of building materials, machinery and mechanisms, transport services, construction and installation and design and survey work, related products. Full list presented in the catalog of goods, works, services. An extensive and professionally verified catalog nomenclature allows you to choose desired characteristics goods for the organization of tenders for the purchase or sale.
More than 50 trading procedures are carried out daily at the StroyTorgy site. Every month, the participants conclude contracts for 700 million rubles. - 1 billion rubles, of which 24% - for the supply of metal products, 13% - for concrete, 13% - construction and installation works, 12% - non-metallic materials, 10% - services of machines and mechanisms, 8% - oil products, 5% - cable and wire products, etc.
A wide range of companies cooperate with the trading platform, including top 20 - 50 suppliers in each category of building materials. Among them are EVRAZ, Mechel, Metallokomplekt-M, A Group, Ariel Metall, Metalloservice, TechnoNIKOL, Isolux, Cable-Trade, Polyplastic, Promnefterodukt, Eurobeton, ABS TsDS, BSU-155, National Non-metallic Company, Basalt, GSP-trade and others .
To work on the site, you do not need to change business processes and buy licenses for additional software - the StroyTorgi service works completely online and is a SAAS product that is available from any device and anywhere where there is an Internet connection.
The main method of organizing trade and purchasing activities is an auction.
Participants of the StroyTorgi system have access to ample opportunities for holding auctions, adapted to the specifics construction market:
- Depending on who initiates the auction, a Seller's Auction (the one who offers the highest price wins) or a Buyer's Auction (the one who gives the lowest price wins) is possible.
- According to the method of selection of participants. Open Auction (all companies registered in the system can take part) or Closed Auction (participants are invited personally by the auction organizer).
- Auction "Profile suppliers" - the ability to invite suppliers from a specific category of goods "with one button".
- Auction of the "Group of Companies" - an opportunity to invite all suppliers approved by the holding from a single list "with one button". Information about the auction will be available not only to the organizer, but also to the parent company of the holding.
- According to the degree of urgency. Standard Auction (bidding starts no earlier than a day after the announcement) or Express Auction (it takes two hours from the announcement of the auction to the start of the auction, about three hours to the end of the auction).
- The degree of confidentiality. Regular Auction (bidders are hidden from each other, the final protocol is visible to all participants) or Auction with confidentiality (bidders are hidden from each other, only the organizer and the winner can see the final protocol).
- According to the terms of delivery. Auction with a fixed volume of goods or Auction with tolerance (when it is impossible to accurately determine the volume of purchase, the Buyer can choose up to +/- 25% of the declared volume without penalty, the Seller is obliged to deliver the goods within the indicated range at the agreed price).
- Auction for similar goods is an opportunity to organize auctions not only for a specific product, but also for goods with similar characteristics, which will allow you to conclude a deal at the best price.
- Two-stage Auction - held in the case when the organizer of the auction does not own complete information about prices. At the first stage, the Buyer announces an auction without a starting price, collects proposals for prices and lot sizes. At the second stage, he sets the price and, after the auction, concludes a contract with one or more Sellers who participated in the first stage.
BENEFITS AND OPPORTUNITIES
- For owners:
- Full control of what is happening in the company's procurement structure
- Practically proven savings of at least 5% of the budget for the purchase of building materials and payment for works and services
- Increasing the investment attractiveness and market value of the company
- For senior management:
- Efficient procurement policy and accountability to shareholders
- Transparent bidding and procurement processes
- Transaction legitimacy guarantee
- Market Analytics
- For the Purchasing Manager:
- Possibility of complex purchases
- Opportunity to establish new business relationships
- Simplicity and convenience of concluding a transaction immediately after the auction results
- Automation
- For the head of the Sales Department:
- Market expansion
- Sales increase
- Opportunity to get market analytics
COST OF USE
In the StroyTorgi system, only the one who makes a profit pays for services - the Seller who concluded the deal at the end of the auction. He pays a trading fee of 1% of the contract amount. The rest of the bidders pay nothing.
For all customers of the service for free:
- Registration/Accreditation in the System
- Announcement of tenders and participation in tenders
- Information about specialized suppliers and buyers of specific categories of goods/works/services
- Analytics on the cost of building materials, works and services for actually concluded transactions
- "Direct communication" - the ability to directly contact the owners on the site construction companies for specific transactions
