How to wash yellow smudges in the toilet. How to clean the toilet cistern from rust? Household chemicals

How to clean a rusty toilet? This question is asked by many housewives who dream of keeping clean and pleasant. appearance plumbing fixtures in the bathroom.

Where does rust come from?

The causes of rust stains on the surface of the toilet bowl can be different. Often the culprit is the chemical composition of the water. Rust is caused by an abundance of various iron salts in tap water. It is possible to deal with such a problem - for this, special capsules or tablets should be added to the tank. They change the chemical composition of water, neutralizing harmful compounds, and also give the water a pleasant smell.

If the quality tap water there is no doubt that the source of rust can be old pipes made of non-galvanized steel. The way out is either to add tablets to the drain tank in the same way, or to replace the pipes with polypropylene or metal-plastic ones.

The appearance of stains, including rusty ones, is promoted by the rough surface of the toilet bowl, for which pollution “clings”. This problem is typical for faience toilet bowls. But porcelain have more smooth surface, which gets dirty much less, and you have to remove rust from the toilet less often.

Rusty marks are also guaranteed if the tank is leaking and water is constantly flowing from it in a thin stream. In this case, it will not work to remove rust from the toilet for a long time until the malfunction is fixed.

In order not to regularly do the pointless work of cleaning the surface of the toilet, you should try to remove or minimize the causes of rust.

How to remove rust?

The whole wide range of anti-rust stains can be divided into two large groups- folk and shop.

Household chemicals

1. Abrasive. This group includes all products whose cleaning action is based on the mechanical action of powder particles on pollution. An example of such a tool can be the well-known Pemolux. Such a tool should be applied to a rag or sponge and rub the rusty stain until it disappears completely. Although such products are quite effective in the end, removing stains takes a long time. In addition, small sharp fragments of the powder scratch the surface, which means that later pollution will be easier to form on it.
2. Alkaline. They act by dissolving contamination without mechanical damage to the surface. Such products are applied to the stain for 10-15 minutes, and then washed off with water. They are considered quite effective, but chronic pollution is not always possible to wash with them.
3. Acid. Like alkaline, such substances simply dissolve pollution. Good for removing all types of stains, even the oldest ones. But due to the high aggressiveness of such products, it is recommended to work with them at home with gloves, and also avoid getting them on open skin and eyes. Acids are great for faience and porcelain toilets, but you should not use them for enameled baths - they dissolve the enamel.

Do not mix several household chemicals- this can lead to unpredictable chemical reactions and damage to the surface of the toilet bowl.

Folk recipes

1. Vinegar . A rag soaked in vinegar essence is placed for half an hour - an hour on a contaminated area, after which this place is rinsed with water.
2. Peroxide and ammonia. Mixed in a ratio of 1 to 10, these two substances are applied to the stain for several hours.
3. Oxalic acid. The agent is applied to the rust for about an hour, after which this place should be wiped with a sponge dipped in ammonia, and then rinsed with plenty of water.
4. Hydrochloric acid. The rusty stain is filled with acid, left for a few minutes, rinsed with water.

Little tricks

How to remove rust from the toilet if there is no cleaning agent at hand?

1. Small stains can be removed with toothpaste. It should be applied to the rusty area and cleaned with a brush.
2. It is believed that rust and lime deposits on plumbing fixtures can be washed off with drinks such as Cola, Sprite, Fanta, etc. You should moisten a rag with them and leave it on the dirt for a while, and then rinse the place water.
3. Battery electrolyte copes well with stains, although this is not its main purpose. The liquid is applied to the stain for a quarter of an hour, and then washed off.

In order for plumbing to shine and delight the eye with whiteness, it is necessary to eliminate all its breakdowns in a timely manner and carry out regular cleaning. It is quite obvious that recently appeared dirt is much easier to wash than stubborn old stains. And when buying plumbing, you should give preference to devices with a special water-repellent glaze, which will prevent the appearance of pollution.

A bathroom in any home should always be kept clean and tidy. Further, we will find out in detail how to clean old stains of limescale and rust in the toilet bowl, bathtub and cistern.

If you carefully use plumbing, it will last a long time. It is also important to keep toilets, tubs, showers, etc. out of the way. clean. Even though it's not easy. The presence of various components in tap water contribute to the formation of unsightly limescale, rust, which cannot be removed by simple washing. Powder products do not always even cope with such contaminants. Let's explore all the possible methods of dealing with this problem.

How and how to remove rust and limescale from the toilet: tips

If the toilet does not yet have old raids and rust, then the usual simple cleaning measures can save the situation. It is possible to wash all the components of the bathroom with a brush and any toilet cleaner, even prepared on your own at home. It will be enough just to take such a tool and apply it to the surface of the toilet bowl inside, just first remove the water from it. Give it a little time to work, then rub it with a brush and rinse. You should like the result.

IMPORTANT: Chemical composition special cleaners for plumbing has harmful substances for the body. Use protective equipment to work with them. Be careful not to get gels or liquids on your skin.

Cleaners for removing rust from the toilet: a list with names, application

Hard water is always the root cause of urinary stones. And when the barrel leaks, such deposits appear more often than usual. If rust spots are visible on the surface of the toilet, then the water contains a large number of iron - this happens through the fault of the old pipeline.

One of the most effective pollution control options is chemicals that are sold on the shelves of supermarkets, shops. Almost any of them will be suitable for solving the problem.

Cleaning the toilet from rust - products

To those funds can be counted:

1. Gel Cillit Bang, Domestos, Comet
2. Faberlic, Sanfor, Chistin, Stork
3. toilet duck
4. Sarma, Chistin and others.

The cleaning method is written on the product labels themselves. Many of them have bad smell, which is harmful to health, so use a mask when working with them.

Rust neutralizer for cleaning the toilet: name, how to use?

With this rust converter, you can effortlessly clean the bathroom from rust stains and plaque. Tsinkar you will find in the hardware store, construction supermarkets or on Internet portals. With it, you will cope with pollution in a few minutes. It will be enough to apply it, and after a while wash off the surface. If stains of dirt are deeply ingrained into the surface of the toilet bowl, bathroom, then leave the neutralizer for thirty minutes, and then use a brush to wipe off the plaque. Flush the toilet several times to remove any remaining contaminants and products.

How to clean the toilet from rust with soda ash: a recipe

This product works great both in combination with other products, and separately. She can wash fresh stains of rust, urinary stone, if you rub the surface with a ruff.

Alternatively, you can do the following:

1. Take soda and pour on pollution, leave for two hours
2. Then pour in the vinegar.
3. Take a brush, brush the surface and rinse.

Soda ash is a much stronger alkali than usual. You can use it without other additives.

Soda ash - bathroom, toilet rust removal

How to get rid of rust in the toilet bowl at home, with improvised means?

If you do not have special cleaning products, then you can get by with other handy ones that are also quite effective. For home cleaning of plumbing, vinegar, soda, powder, whiteness, citric acid and even Coca-Cola are suitable.

Home methods for cleaning plumbing from rust

• To take away yellow spots on plumbing, use nine percent vinegar. Just pour it on the surface where there is dirt overnight, rinse thoroughly in the morning cold water, ruff.
• The same can be done and acetic acid , just do not hurt to close the toilet lid and keep the product on its surface for at least six hours. If you can’t get rid of the stains right away, then repeat the whole process a few more times.
• More to be good effect put toilet paper on the inside of the toilet bowl, soak it vinegar so that the stains are better eaten off.
• Limescale can be washed off hot water with ammonia. More precisely, you must first apply alcohol, and then rinse everything with hot water.
• Usual bleach also effective in the fight against rust, it must be applied for several hours on the surface, and then washed off.
• Washing powder paired with soda copes well with old rust stains on toilets, bathrooms. It is only necessary to fill the surface with this composition, rub it with a sponge after a while, strongly stubborn stains are cleaned with this mixture with ammonia.
• Vinegar mixed with iodine eats up plaque well. But first, the vinegar must be heated to forty-five degrees. Then add a little iodine, only after this process, pour the solution into the inside of the toilet bowl without water. Leave it overnight like this, wash it off in the morning.
• Coca Cola works in the same way as vinegar with iodine. If the stains are deeply ingrained, then use the drink several times until you get the desired result.
• Do the same with whiteness. To prevent the smell from spreading to all rooms, close the toilet with a lid.

If you use strong reagents too often (hydrochloric acid, iodine monochloride, dry oxalic acid), then your plumbing will become unusable. The surface of the bathroom, toilet bowl will get microcracks, then it will become rough - general form will deteriorate. Therefore, do not bring it to severe pollution, clean the plumbing more often with non-aggressive means, then it will last a long time and will have an attractive appearance.

The hygiene in the house and the cleanliness of the living can be judged by the state of the plumbing. A dirty toilet with yellow smudges does not add to the image of the owners, and you can clean the toilet from rust with household chemicals or improvised compounds. You just need to want to remove the pollution.

We use household chemicals

The most effective and easiest way to clean rust in the toilet is with the use of professional store compounds. Let's consider them in more detail.

Abrasive "Pemolux" and its analogues ( "Komet", "Sarma", "Sorti", "Sanita"). The powder is applied to the pre-moistened contamination with a napkin and the composition is left to interact with the surface for up to half an hour. Then they are cleaned by rubbing with a hard sponge or brush, the powder is washed off with water.

The use of abrasives is effective, but there is one caveat. When used, microcracks appear on the surface. With each time, the destruction intensifies, the pollution penetrates deeper and more difficult to cleanse. It turns out that the more often the toilet is washed with Pemolux or the like, the dirtier it becomes.

Advice
When choosing a toilet, give preference to porcelain sanitary ware, which, unlike faience, is less porous and less prone to contamination.

Alkaline compounds like Domestos, Dosya, Sarma gel. They corrode the dirt without harming the surface. Apply the product, applying to the area with rust and leaving for 15-20 minutes. Then washed with water. The method is simple and not time-consuming, but severe pollution may not succumb to it.

Advice
Alkaline compounds with chlorine are used to clean plumbing and bleach to a dazzling shade.

Special means "From rust" with acid in the composition, primarily oxalic. Among these stand out efficiency "Silit", "Sanita", "Toilet Duck". The principle of cleaning them is based on the dissolution of contaminants, as with the use of alkaline compounds. Therefore, the method of their use is the same - the liquid is applied to the contamination, left for 10-20 minutes and washed off with water.

Advice
The acid is caustic and should not be used on enamelled plumbing. But for faience and porcelain, compositions with acid are just that.

Cleansing folk remedies

At home, you can use improvised acidic and alkaline substances: soda, vinegar, citric acid or juice.

Vinegar Soda

The inside of the toilet bowl is whitewashed using several household methods using vinegar and soda. With their help, you can remove from the toilet not only rusty smudges, but also yellowish urinary stone.

Method 1:

1. 1 glass of vinegar essence or table vinegar is heated to 45 ° C.
2. Mixed with 1 tbsp. l. soda.
3. If the product is prepared from 9% vinegar, then a few drops of iodine should be added to the prepared mixture.
4. The resulting composition is applied to the problem area of ​​plumbing. If you need to clean the toilet under the rim, then use a container with a narrow opening.
5. Leave for up to 12 noon.
6. Wash off with water.
7. If you are not satisfied with the result, the procedure is repeated as many times as necessary.

Method 2:

1. Pour half a glass of soda into the toilet.
2. Then it is carefully poured with vinegar.
3. The hissing mass is distributed with a brush over the entire inner surface of the toilet bowl.
4. They wait half an hour, clean the dirt well with a brush.
5. Washed with water.

Baking soda

It belongs to soft abrasives and has a safe action. A gruel is prepared from soda and water, which is applied to the area with rusty stains. After drying, the product is washed off with water.

table vinegar

To wash the plumbing, they are abundantly impregnated with a cloth napkin and well moistened with rusty marks. Leave for half an hour or an hour, then rinse with water.

In this way, it is effective to wash the stepped toilet (“with an oblique outlet”). Water is first removed from the upper part of the bowl, and during soaking, the drained vinegar is periodically lifted and distributed again along the walls.

ammonia and hydrogen peroxide

They are used in a similar way to vinegar:

1. Mix peroxide and ammonia in a ratio of 1:5.
2. The agent is applied to the contamination.
3. After waiting half an hour, rub with a brush and rinse with water.

Ammonia has a pungent odor, so be sure to turn on the hood or ventilation amplifier, and cover your nose and mouth with a medical mask, and preferably with a respirator.

Lemon acid

Its crystals are more effective than vinegar, and the product does not drain from the walls so quickly. Clean with lemon in two ways.

Method 1:

1. Sprinkle citric acid powder on a napkin.
2. Wipe the pre-moistened rust stain.
3. Leave for up to an hour and a half;
4. Washed with water.

Method 2 - if you need to remove rusty plaque and yellow stone:

1. Several packets of acid are poured into the toilet.
2. Leave for 10-12 hours. The urinary stone softens and can be cleansed.
3. Rub with a brush and rinse with water.

Oxalic acid powder

Many housewives call this substance the most rust cleaner.

The powder is used like this:

1. Apply to the surface moistened with water with rubbing movements.
2. Leave for half an hour.
3. Wash with water.

Advice
It is necessary to work with alkaline and acidic compounds, observing safety measures. And be sure to wear rubber gloves.

"Whiteness" and other chlorine bleaches

Method 1:

1. The liquid composition is poured onto the contaminated surface.
2. Leave overnight and then wash off.

Method 2 - radical, but fast:

1. Alkaline powder (for example, "Sanitary") wipe the toilet from the inside, giving Special attention rusty stains.
2. Leave for 5-10 minutes.
3. Pour "Whiteness" into the toilet and wipe all surfaces and drains, distributing the bleach over the powder.
4. Wash well with water.

Important
In the second method, alkali and acid neutralize each other, and chlorine is actively released into the air. Therefore, it is allowed to use this method only with the hood turned on and in protective equipment. Children and animals should move away.

Carbonated drinks

Pepsi, Coca-Cola, Sprite, others dissolve limescale and remove fresh rust stains.

Cleaning Methods:

1. The drink is poured into the toilet. If you need to clean the plumbing under the rim, soak a napkin with soda and apply it to the place with pollution.
2. Leave for an hour.
3. Washed with water.

Advice
Water leaking from the tank significantly reduces the cleaning efficiency, and it also - main reason rusty track at the flush site.

Toothpaste

It is advisable to take bleaching and without color inclusions. Toothpaste- means of soft abrasive influence and helps to get rid only of fresh pollution. Her

Mode of application:

1. The paste is rubbed into a moistened dirty surface.
2. Leave for half an hour.
3. Wash off with water.

Prevention

Cause of rust spots and yellow plaque is water. There is always iron in its composition, and if it leaks from the flush, rust quickly grows on the wall and around the sump in the toilet bowl. If there is a lot of rust in the water, then it remains on the walls even with a fully functional tank. In the first case, it is enough to adjust or replace the flush mechanism, soluble tablets for the tank or fresheners with a cleansing effect that are attached under the rim help in part.

In the case of extremely hard water, more drastic measures will be required. The source of water pollution is non-galvanized metal water pipes that corrode from long-term operation. Accordingly, ideally, the pipes are replaced. As a compromise, a filter is installed on the water conduit entering the house and it is checked monthly and, if necessary, washed or changed. Both procedures are quite expensive.

Rusty deposits on the tank and the surface of the toilet bowl spoil the appearance of the bathroom and shorten the life of plumbing. Regular care helps to prevent stubborn dirt: weekly washing with anti-rust and lime deposits, timely repair of the tank and replacement of pipes with metal-plastic ones with a cleanable filter.

An unpleasant rusty streak can form in the toilet bowl. This defect appears as a result improper care behind the toilet or for internal reasons. To get rid of it, you can use not only purchased funds, but also improvised methods.

Removing rust with chemicals

There are three types of chemicals that can be used to remove toilet rust:

Abrasive cleaners

These include the popular tool "Komet".

Application:

• An abrasive must be applied to a rag or brush.
• Thoroughly wipe the area with rust. You can clean dry or wet surfaces. It is important that there is not much water there.

You will have to try to scrub the stains, but the low cost of abrasive products can be attributed to the pluses.

Carefully! Such cleaners, along with a layer of rust, can also erase the “enamel” of the toilet, so it is important not to overdo it.

Alkaline products

You can highlight the popular "Domestos".

Application:

• Apply a small amount of detergent to the dirty area.
• Leave it on for 20-25 minutes.
• Rinse thoroughly.

This best option, since you do not have to contact with "chemistry". All the work is done by alkalis, which remove rust, but do not damage the material.

Alkaline products will not help only if the rust layer is too thick.

Acid remedies

These include "Cillit" and "Toilet Duck" (especially effective black bottle).

Application:

• We apply the product to the place of pollution;
• We wait about half an hour;
• Rinse off the cleaning agent thoroughly.

As you can see, acid products are used in the same way as abrasive ones. Be careful, since the acid is dangerous for the skin, perform all manipulations with protective gloves.

The main advantage of acid products is the high efficiency of rust control, in this parameter they bypass their other competitors.

We use improvised means

Some folk methods are as effective as chemicals without having to go to the supermarket. Today, "chemistry" is quite expensive, so improvised means are great way save:

• A solution of hydrogen peroxide and ammonia . We take 5 g of ammonia and mix it with 100 g of peroxide. The resulting solution is applied to the area with rust, leave the mixture for half an hour, then wipe the damaged area with a brush and wash off the mixture.
• electrolyte for batteries . If you suddenly have this solution lying around at home, then you can use it to clean the toilet from rust. Apply the substance to the rusty area and wait 30 minutes. Rinse thoroughly and you will have a clean toilet.
• Hydrochloric acid . To remove rust, you need about 20 g of the substance. Apply acid to the stain and leave for 20 minutes. Rinse off the product with hot water (do not take boiling water). In addition to gloves, it is recommended to use a respirator.
• White . The method will work if all the liquid is removed from the toilet bowl. Pour a bottle of whiteness down the toilet and leave it overnight. Rinse off the product in the morning, most likely, all rusty spots will leave the surface.

We decided not to include the Coca-Cola rust removal method in this list, as the method is not very effective. The rest of the methods have been tested, so you can look in the pantry for suitable solutions and materials.

Video: Cleaning the toilet from rust and plaque

The video describes in detail and demonstrates the methods of getting rid of rust. After watching the video, you can clearly see how chemicals and folk methods work.

Another experienced housewife will share her secrets:

What causes rust in the toilet?

The brown stripe can most often be seen in the houses of the CIS. And all because pipes made of non-galvanized steel are installed in our dwellings. The water entering the house contains many substances that adversely affect the walls of the pipeline. However, the main cause of rust is a large amount of iron in the water.

The rapid appearance of rust is also influenced by other factors:

• There is always water in the toilet bowl - in this case it is recommended to solve the problem with the tank from which the liquid flows.
• Rough surface of the toilet. Harmful elements, falling on the surface, are practically not washed off, which provokes the appearance of yellow stripes.

Useful advice! In order not to spend a lot of time cleaning the toilet, it is necessary to prevent rust from forming a thick layer. Clean once every 2 weeks or more, and then the plumbing will have a well-groomed appearance. Also, don't forget about .

The cleaning procedure is quick if the state of the toilet is not running. It is effective to use special tablets that prevent the appearance of rust spots. It is worth working with the tank if water constantly flows from it. You will not only get rid of rust, but also protect the material from future formations.

As folk wisdom says, the owner of the apartment is judged by cleanliness kitchen utensils and a bathroom. If cleaning is carried out regularly, then the latter will not cause discomfort to guests and residents of the apartment. However, how to remove rust from the toilet if the cleaning has not been carried out for a long time (months, and possibly years)?

People often encounter similar situations when purchasing housing on the secondary market, when moving into a hostel or a communal apartment. Besides rust, big problems create deposits of limescale and urinary stone in the toilet bowl. How to deal with all this? And is it even worth cleaning up? Would it be easier to spend money on a new toilet? The reader will find answers to all these questions in this article.

Types of pollution of the toilet bowl

The most common types of soiling are limescale in the toilet, as well as urinary stone and rust streaks. There are other types of pollution. But they are usually artificial.

For example, potassium permanganate stains that are almost impossible to remove (especially if the enamel on the surface is missing or damaged). It would not be superfluous to give a more detailed description and description of each of the listed contaminants.

urinary stone

It is a plaque of minerals that are excreted from the human body along with urine. Imperceptibly to the naked eye, these substances are deposited on the surface of the toilet with each visit. If you do not periodically clean, then over time, these deposits become noticeable. The plaque has a dark yellow (in some cases gray) color. Removing this type of contaminant is not an easy task. To do this, you need a special one for the toilet.

These substances are most intensively deposited on a rough surface. Thus, most often deposits form on surfaces with damaged enamel. The appearance of such growths occurs on a smooth enameled surface. This happens if the toilet is often not flushed after a visit. Most often, this problem occurs in public restrooms. In some cases, the situation is so neglected that no toilet cleaner can help. When the thickness of the deposits reaches a certain critical minimum, they begin to exude an extremely unpleasant odor, which is greatly enhanced by the breeding and multiplying bacteria.

limescale

This type pollution is in many respects similar (first of all, by the nature and principle of formation) to urinary stone. After all, this is also a plaque of minerals. The difference lies in the fact that these substances are contained in tap water and settle on the inner surface of the toilet bowl when the tank is drained. It is quite clear that the worse the quality of the water in the water supply, the more intensive the growth of deposits will be. Also, the frequency of draining the tank also affects the rate of stone formation.

Limescale in the toilet bowl has a dark yellow, in some cases even orange color. The build-up occurs and grows in areas of the toilet bowl that are difficult to reach for cleaning products, through which water flows when draining. If the quality of tap water is very low, a stone can clog the drain holes. In such advanced cases, even very active and potent powders and gels for cleaning the toilet are powerless. Holes can be punched mechanically. But this measure is temporary. It is best to change the toilet with a tank.

Rust streaks

Rust is very difficult, almost impossible to confuse with stone deposits. Formed in the place where water flows out of the tank. Moreover, the less often the toilet bowl is flushed, the more likely it is that rust stains will form. This is due to the fact that standing water is saturated with dissolved iron oxide (in fact, this is rust), which settles on the surface of the tank when flushed. There are a lot of toilet rust removers on the market. But not all of them are effective. This article focuses on the means and methods of dealing with rust on the surface of the toilet, as the most common problem.

How to remove rust from the toilet with the help of folk remedies?

Previously, in the years of the Soviet past, not to mention tsarist times, the choice of household chemicals was very poor. People resorted to improvised means. And it should be noted that sometimes these methods turned out to be very effective in combating pollution. different nature. It would be fundamentally wrong to reject the experience of previous generations. In addition to being cheap and readily available, folk remedies have another important advantage - manufacturability. What is meant by this? First of all, the ability to work without fear of damaging the plastic pipeline. But in most houses at the present time (during construction or overhaul) water and sewer pipes made of polyvinyl chloride are installed.

The most famous remedy is, of course, citric acid. How to remove rust from the toilet with this powder? Everything is very simple. All you need is 100-150 grams of citric acid, protective gloves and a hard-bristled brush (a ruff will do).

All water is scooped out of the toilet bowl, problem surfaces are sprinkled with citric acid. It will take at least four hours for the acid to react with the dirt and soften the stones. Next, clean the surface with a sponge or brush. After that, the remnants of citric acid and dirt are washed off with water. This procedure must be repeated several times to achieve maximum effect. Here, in general, and all.

The surface cleaning process will be greatly accelerated if citric acid is mixed with vinegar. More precisely, if vinegar is applied to a layer of acid powder with a sprayer. Many people recommend using just vinegar. This method is also quite effective.

In general, a variety of combinations are possible: vinegar plus soda, baking soda with the addition of calcined in different proportions, and even Coca-Cola and other drinks, which include phosphoric acid.

Cleaning with Domestos for the toilet bowl and other household chemicals

Classic detergent disinfectant in the countries of the former Soviet Union is the so-called whiteness. It has a very pungent odor and is quite effective not only in cleaning clothes from stains, but also in washing the bathroom. It is necessary to apply whiteness to the contaminated surface with a sprayer and wait only 15-20 minutes. During this time, plaque and rust should lag behind the surface, after which the dirt is washed off with water. It is a rather caustic substance. When working, do not allow it to get into the eyes and on bare skin. Therefore, gloves must be worn.

"Domestos" for the toilet (and other special chemistry) operates on a similar principle. However, it is, as a rule, much more expensive than ordinary whiteness. The difference in cost is compensated by a pleasant aroma and the absence of irritation of the nasal mucosa.

Using harsh chemicals to clean the toilet

This method is resorted to only in special cases, when neither conventional chemistry nor folk remedies help. All work should be carried out with extreme caution. After all, you can not only damage the enameled surface, but also harm your own health.

To clean heavily soiled surfaces of the toilet, you can use hydrochloric, phosphoric, and oxalic acid. Of course, all work must be carried out in compliance with safety precautions and with the use of personal protective equipment.

Acid should not come into contact with rubber products and plastic, as parts made of these materials will instantly become unusable.

Using battery electrolyte as a detergent and cleaning agent

It is quite difficult for an ordinary person to get acids without having acquaintances in chemical laboratories and research institutes. In here, the battery electrolyte can be easily obtained. It must be said that this is very effective remedy in the fight against rust streaks and stone deposits.

How to remove rust from the toilet using electrolyte? Yes, very easy! It is necessary to very carefully apply the substance in an even layer on the surface of the toilet bowl and leave for no more than 10 minutes. After that, you have to work a little with a brush or brush - and you're done! It remains only to wash off the reaction products with water. Toilet like new!

The electrolyte is classified as a hazardous substance. Skin contact and eye contact should be avoided. The consequences can be very severe.

Help from professionals

If there is no desire or necessary experience, then you can contact a specialized cleaning agency. There are a lot of such organizations in recent years. Specialists are ready to come to the customer's house at any time convenient for him and carry out cleaning. These employees have a large arsenal at their disposal. detergents allowing you to easily cope even with years of dirt and deposits. The only drawback of such a solution to the problem is the rather high price tag for the services of such agencies.