Children's slide for a country house or cottage with their own hands. Synthetic brush coating SnowPlast for slides and ski slopes to ensure sliding both on ice and snow Make a slide out of metal

If you have children and country cottage area, then it is necessary to build a hill on it. While the parents will be engaged in the garden or cooking barbecue, the children will have fun on the mini playground. Read about how to plan and make a slide with your own hands with us, using photo and video instructions in practice.

Height and safety

The slide on the site should be primarily safe for children different ages. So, for kids under 2 years old, the height of the slide is only 1.5 meters, for children from 2 to 7 years old, a height of about 2.5 m is chosen, and for teenagers 3-3.5 meters. The steps on the stairs of the slide should be wide, and the rungs should be located close to each other. Further, the design of the stairs must be equipped with handrails of any type: after climbing the hill, the child must hold on to something.

Advice! In order for the slide to serve more than one generation of children and be safe on the stairs and around it, an anti-slip coating is laid. The cover protects children from injury when getting up in the rain, snow or after swimming in the pool.

Another milestone in creating a safe slide is the calculation of the weight of the children who will ride it:

The height of the slide depends on the age of the children

1. The slide is fixed on a base or supports that can easily support the weight of 2-3 children.
2. A smooth chute is responsible for safety during the descent, it is good to make bumpers on the sides to prevent the child from falling out.
3. All bolts, chips, chips or sharp corners on the slide for children are excluded. The tree is polished so that the baby does not drive a splinter.

Advice! Under the chute along which the child descends, a soft patch is placed - this lawn grass, sand mound or soft cover.

Choosing a place to place a children's slide

The slide is located in the place where it opens good review from anywhere in the area. But make sure that the place for games is not under the sun. In the case of such an arrangement, it is worth considering the construction of a canopy.

Advice! The canopy is made of polycarbonate, and an ordinary beach umbrella is also suitable for a low slide.

Wood slide

slide from natural wood distinguished by its environmental friendliness and ease of installation, it consists of the following elements:

1. Base.
2. Staircase with railings.
3. Descent.
4. Top platform and protective details.

Such a slide can be supplemented with a whole of labyrinths, bars, a sandbox or mini rooms with entrances and exits. The construction of a wood slide consists in the selection of high-quality raw materials and its normal processing.

wooden slide

The slope is made of plywood, pre-varnished to hide sanding errors. The supporting structure is made of timber, and the steps are made of strong boards.

Important! Today on sale there are various slopes made of durable plastic, fiberglass or wood. The minimum price of a slope is 1.5-2 thousand rubles. The best option is the creation load-bearing structure for a slide with the subsequent installation of a flat or screw slope.

A wooden slide is good for everyone, but located in an open space after 3-5 years it can dry out, be damaged by insects or mold. Wood rots from rain, and the situation can be saved by covering each structural element with a thick layer of varnish. But after winter and hot summer, the hill is worth inspecting, revealing cracked or cracked parts.

Metal slide

Previously, metal slides stood in every yard, distinguished by their strength and durability. Such designs are more reliable, because they are not afraid of either the hot sun, or rain, or frost.

The construction of such a slide is carried out in several stages:

1. The most primitive foundation is poured, you can immediately pour 4 support pipes, as is done when installing fences.
2. Further, a staircase and a railing are welded onto 2 pipes on one side, the remaining 2 pipes are used to attach the gutter.
3. A platform is welded to all pipes.

Important! The gutter is 2 metal pipes, to which a sheet of metal bent in shape is welded. After assembling the slide, all welds must be ground; a grinder is used for this purpose.

After completing the assembly of the structure, the slide can be painted with plain paint or painted. The metal gets very hot under the sun, so on hot days you should close the slide with a beach umbrella so that children do not burn their skin.

Playground with slide and swings

A simple slide can be made by descending from the house, which is also built with their own hands, using timber or the remains of building materials:

1. Concrete piles are mounted in 4 old automobile tires and on which bars of the required height are installed vertically. The beams are fixed with building corners.
2. Along the perimeter of the racks, a frame for the house is installed, with holes for entering through the stairs, and leaving through the hill.
3. After that, a light but durable ladder, a gutter for descent, the floor and walls of the future house are mounted. The elements are fastened with self-tapping screws, and the entire wooden structure must be smeared with an antiseptic.
4. Holes are drilled at the joints of the timber, tightening the structure with 120 mm bolts.
5. Next, the truss elements from the timber for the roof are laid. The final roof covering is made of corrugated board. Often used decorative tiles made of ordinary painted foam.

The last step is to cover the entire structure with a layer of varnish.

How much does a finished slide cost?

In order not to suffer with manufacturing, you can simply purchase a slide:

• Inflatable slide for the little ones. Such a slide is an ideal solution for small children, because it can be equipped with a shallow pool, a mini trampoline or educational elements. The cost of an inflatable slide starts from 4 thousand rubles, usually it has a height of more than 1.4 m. The advantages of the slide are its mobility, resistance to temperature extremes, and after the child grows up, the inflatable center can be profitably sold.

You can buy a slide, but it will be more expensive than self-building

• Play sets made of plastic, in some cases combined with wood. This type of city is more expensive, and the minimum cost starts at 4.5 thousand rubles for the most primitive model. But slides made of plastic can combine swings, bars that develop the muscular corset, a basketball basket and much more. Thanks to the fastening system, the height of the gutter can be adjusted, adjusting it to the age and height of the child.

Creating a children's slide is a creative process, and a full-fledged play area requires swings, a sandbox, and even a football goal. But building these elements of a children's corner is much cheaper on your own, because buying finished product requires 60% more material resources.

Do-it-yourself children's slide: video

Slide for children in the country: photo

If you have children and a summer cottage, then you should definitely build a slide on it. While the parents will be engaged in the garden or cooking barbecue, the children will have fun on the mini playground. Read about how to plan and make a slide with your own hands with us, using photo and video instructions in practice.

Height and safety

The slide on the site should be primarily safe for children of different ages. So, for kids under 2 years old, the height of the slide is only 1.5 meters, for children from 2 to 7 years old, a height of about 2.5 m is chosen, and for teenagers 3-3.5 meters. The steps on the stairs of the slide should be wide, and the rungs should be located close to each other. Further, the design of the stairs must be equipped with handrails of any type: after climbing the hill, the child must hold on to something.

Advice! In order for the slide to serve more than one generation of children and be safe on the stairs and around it, an anti-slip coating is laid. The cover protects children from injury when getting up in the rain, snow or after swimming in the pool.

Another important step in creating a safe slide is calculating the weight of the children who will ride it:

The height of the slide depends on the age of the children

1. The slide is fixed on a base or supports that can easily support the weight of 2-3 children.
2. A smooth chute is responsible for safety during the descent, it is good to make bumpers on the sides to prevent the child from falling out.
3. All bolts, chips, chips or sharp corners on the slide for children are excluded. The tree is polished so that the baby does not drive a splinter.

Advice! Under the gutter, along which the child descends, a soft piece is placed - this is lawn grass, a mound of sand or a soft surface.

Choosing a place to place a children's slide

The slide is located in the place where it has a good view from any point of the site. But make sure that the place for games is not under the sun. In the case of such an arrangement, it is worth considering the construction of a canopy.

Advice! The canopy is made of polycarbonate, and an ordinary beach umbrella is also suitable for a low slide.

Wood slide

A slide made of natural wood is distinguished by its environmental friendliness and ease of installation, it consists of the following elements:

1. Base.
2. Staircase with railings.
3. Descent.
4. Top platform and protective details.

Such a slide can be supplemented with a whole play complex of labyrinths, bars, a sandbox or mini rooms with entrances and exits. The construction of a wood slide consists in the selection of high-quality raw materials and its normal processing.

wooden slide

The slope is made of plywood, pre-varnished to hide sanding errors. The supporting structure is made of timber, and the steps are made of strong boards.

Important! Today on sale there are various slopes made of durable plastic, fiberglass or wood. The minimum price of a slope is 1.5-2 thousand rubles. The best option is to create a supporting structure for the slide, followed by the installation of a flat or helical slope.

A wooden slide is good for everyone, but located in an open space after 3-5 years it can dry out, be damaged by insects or mold. Wood rots from rain, and the situation can be saved by covering each structural element with a thick layer of varnish. But after winter and hot summer, the hill is worth inspecting, revealing cracked or cracked parts.

Metal slide

Previously, metal slides stood in every yard, distinguished by their strength and durability. Such designs are more reliable, because they are not afraid of either the hot sun, or rain, or frost.

The construction of such a slide is carried out in several stages:

1. The most primitive foundation is poured, you can immediately pour 4 support pipes, as is done when installing fences.
2. Further, a staircase and a railing are welded onto 2 pipes on one side, the remaining 2 pipes are used to attach the gutter.
3. A platform is welded to all pipes.

Important! A gutter is 2 metal pipes to which a sheet of metal bent in shape is welded. After assembling the slide, all welds must be ground; a grinder is used for these purposes.

After completing the assembly of the structure, the slide can be painted with plain paint or painted. The metal gets very hot under the sun, so on hot days you should close the slide with a beach umbrella so that children do not burn their skin.

Playground with slide and swings

A simple slide can be made by descending from the house, which is also built with their own hands, using timber or the remains of building materials:

1. Concrete piles are mounted in 4 old automobile tires and on which bars of the required height are installed vertically. The beams are fixed with building corners.
2. Along the perimeter of the racks, a frame for the house is installed, with holes for entering through the stairs, and leaving through the hill.
3. After that, a light but durable ladder, a gutter for descent, the floor and walls of the future house are mounted. The elements are fastened with self-tapping screws, and the entire wooden structure must be smeared with an antiseptic.
4. Holes are drilled at the joints of the timber, tightening the structure with 120 mm bolts.
5. Next, the truss elements from the timber for the roof are laid. The final roof covering is made of corrugated board. Often used decorative tiles made of ordinary painted foam.

The last step is to cover the entire structure with a layer of varnish.

How much does a finished slide cost?

In order not to suffer with manufacturing, you can simply purchase a slide:

• Inflatable slide for the little ones. Such a slide is an ideal solution for small children, because it can be equipped with a shallow pool, a mini trampoline or educational elements. The cost of an inflatable slide starts from 4 thousand rubles, usually it has a height of more than 1.4 m. The advantages of the slide are its mobility, resistance to temperature extremes, and after the child grows up, the inflatable center can be profitably sold.

You can buy a slide, but it will be more expensive than self-building

• Play sets made of plastic, in some cases combined with wood. This type of city is more expensive, and the minimum cost starts at 4.5 thousand rubles for the most primitive model. But slides made of plastic can combine swings, bars that develop the muscular corset, a basketball basket and much more. Thanks to the fastening system, the height of the gutter can be adjusted, adjusting it to the age and height of the child.

Creating a children's slide is a creative process, and a full-fledged play area requires swings, a sandbox, and even a football goal. But building these elements of a children's corner is much cheaper on your own, because buying a finished product requires 60% more material resources.

Do-it-yourself children's slide: video

Slide for children in the country: photo

Parents who have small children often have to visit playgrounds so that the child swings, plays in the sandbox, and rides down the hill. But adults do not always have enough time for such events, especially if the site is far away. Having your own plot, you can make such entertainment for a child at home. This will solve many problems of parents, and the child will always play under supervision. Today we will talk about how to make a children's slide with your own hands from improvised materials.

A metal slide is a common building from Soviet times. It was installed on the playground along with the sandbox. Metal is the strongest and most durable material. But under the influence of external negative factors it is subject to corrosion, so for the manufacture of slides it is better to use stainless steel or galvanized metal. At self-manufacturing slides at home must have a drawing at hand.

From materials and tools you will need:

• metal pipes with a diameter of 15-25 mm, rods;
• corners with a section of 50x50 mm, 20x20 mm;
• sheet iron with galvanized coating;
• multi-colored paints, cement, crushed stone;
• welding machine, grinder, crowbar, hammer.

Having prepared necessary materials, at the site of the future installation, proceed to the manufacture of the structure according to the drawing:

1. Start manufacturing with a frame. For the upper platform, weld a square measuring 1.5 x 1.5 m from the corner. Place stiffeners crosswise inside it. Weld on top of the square to the corners a metal sheet not less than 1 mm thick of the same size. If possible, use corrugated iron, it will give stability, and the child will not slip on the playground.
2. Weld the finished platform to the racks. For their manufacture, you need a pipe with a diameter of 25 mm and a length of 3 m. To the ends of the racks, the lower part of which will be concreted, weld the heels from any metal scraps.
3. Under the welded frame, mark and dig 4 holes about 1 m deep with a drill. Tamp the bottom with small stones or rubble. Lower the frame racks into the pits, aligning the structure with a plumb line. Knead cement mortar with rubble and fill in the holes. After about a week, the solution will completely harden and you can continue building.
4. From a 20 mm pipe for stability, cross-weld the frame strapping between the uprights. From the edge of the platform down to the ground at an angle of 45 °, weld a descent from 2 corners with a section of 50x50 mm parallel to each other. Across the corners, weld strips for steps from corners with a section of 20x20 mm at a distance of 20 cm from each other. Sew up the plane of the steps wooden planks or corrugated iron.
5. On both sides of the stepped descent, weld handrails from 15 mm pipe. Sew up the openings between the handrails and the descent with a metal mesh or thin rods.
6. The chute is made from 2 pipes with a diameter of 20 mm. Bend the lower part of the pipes with a pipe bender or by heating with a cutter. You should get a design from a steep descent, smoothly turning into a horizontal plane. top weld gutters to the other edge of the site. Fix stiffeners between the pipes of the gutter. From above, weld galvanized sheet metal with a thickness of at least 1 mm. If it is not possible to make a descent from solid galvanization, then weld smaller sheets with an overlap along the descent.
7. Curve the sides of the gutter fence from a 15 mm pipe. They need to be welded parallel to the bottom at a height of 30 cm, and the sides are sewn up with galvanized sheet metal. In several places, weld supports for the gutter from any remnants of the pipes.
8. The metal structure is ready. It remains to process it with a grinder to eliminate all sharp protrusions. The design can be decorated with multi-colored paints to make it attractive to the child. The bottom of the descent does not need to be painted, otherwise the coating will reduce slip.

Wood slide

Wooden slides at home are easier to make on your own, you don’t need to welding work. wooden structures less durable than metal, but wood can be used to make a beautiful playground with a sandbox, a house, rope ladders and other equipment. For DIY construction, it is better to use wood conifers. From materials and tools you will need:

• 4 beams with a section of 100 x 100 mm, a bar with a section of 50 x 50 mm, edged board section 25 x 150 mm;
• galvanized iron 1 mm thick or linoleum;
• self-tapping screws, nails, antiseptic, varnish or multi-colored paints;
• cement, crushed stone;
• electric planer, grinder, screwdriver, hammer, sandpaper.

Work, as always, start with drawing up a design drawing. Decide whether there will be a slide with or without a house, and draw a diagram of it. This will make it possible to calculate the consumption of material, as well as facilitate further construction.

Everything is ready, you can start carpentry work:

From the remnants of the material, make wooden benches or a sandbox near the slide. They will decorate the playground, bringing joy to children.

Plastic slides

It will not be possible to make a plastic structure on your own, it is only bought in a store. Such slides are produced in one piece and collapsible. The owner can only install a slide on the site. Collapsible models are better suited for giving. They are easy to disassemble for storage. winter period. This will prevent theft and vandalism at a time when the cottages are left unattended by the owners.

V plastic models use different gutters, which is very popular with children. They are screw, tubular, straight and other shapes. If the child still wants an unusual descent, and the parents do not have enough money to buy, you can do it for a summer residence or at home combined option slides. The fact is that the gutters are sold separately. They are also made in any shape to order. You will only have to make metal or wooden frame and attach a plastic trigger to it.

A playground built independently for a summer residence or at home will decorate the yard, provide children with entertainment in the summer.

In contact with

Winters in Russia are getting warmer every year, and therefore the question is very relevant - how to ensure the sliding of tubing, cheesecakes, snowboard or skis in a thaw or even in warm weather in summer? For athletes, this is a matter of keeping fit, and for ordinary people, it is a question of having active recreation in a sports mode and, of course, entertainment for children.

brush slide cover for slides SnowPlast (SnowPlast) art. 150243, made of synthetic modules, will undoubtedly be the ideal solution here. In winter, the brush cover retains snow on the slope, reduces the thickness of the snow cover required for skiing, saves money on snowing the slopes, allows you to open the winter season early, and protects sports equipment from damage during the thaw period. In summer, brush coatings do not spoil appearance green lawn and allow you to fully engage in winter sports and outdoor activities in summer conditions.

The use of a special silicone-based slip fluid improves the sliding properties of the coating, as well as its service life. For slides and tubing tracks, the recommended volumes of such a liquid are, on average, about 10 liters per hundred square meters coverage area per year. The brush cells snap together easily and can be used to cover wooden slides, tubing slopes and ski slopes. Sections can be joined together to form any geometric shape. Therefore, the shape of the slope of the slide, skating rink or ground cover does not matter.

In application, the coating is very convenient, as it is easy to mount and dismantle. The coating array is made up of small, easily interchangeable plastic modules of the same type, 150x300 mm in size. and with a bristle height of 40 mm. By connecting the modules together, you can pave a path or slope surface of any complexity. The coating does not violate the ecology of the slope and its design, does not spoil fertile layer soil. Can be laid on any substrate, such as earth, concrete or wooden decking.

During the entire service life, the brush coating allows the manual to entertainment centers, sports clubs and even resorts to extend the skiing season as long as they want, in fact, to offer their customers year-round winter sports. The Pleten company uses SnowPlast to be able to ride down a wooden slide or ramp all 365 days a year, regardless of the weather and temperature indoors or outdoors. Moreover, SnowPlast allows you to make it possible to arrange slides in warm rooms entertainment game centers and children's parks.

Price synthetic turf for slopes and slides SnowPlast, art. 150243 = 3900 rubles/m2

Installation supervision for the installation of the coating = from 600 rubles / m2
(depending on the total coverage area and the location of the object).
A mixture to improve slip = 1400 rubles / l.
Special tubings for SnowPlast coating = from 5300 rubles/pc.

Children's slide, swing, sandbox for summer cottages. Wooden CHILDHOOD - with your own hands. July 28, 2011

I remembered ... My little miracle began to grow up and for its growth I decided to stock up on heavy artillery in the form of a playground with all kinds of slides, ladders, ropes, swings.
So the long process of creating a coniferous structure began.

Other photos

I devoted a week of my vacation to leveling the site,

so I dug four cubes of sand into the hole under the playground.

Of course, it is not necessary to do this at all, and it was not worth it,

Or at least just under the hill.

where the sandbox is supposed to be.

The child, of course, was warned in advance about dad’s plans, but he couldn’t understand that this same dad had been rummaging through the middle of the site all week, digging up the earth and scattering it all over the garden, but when the KAMAZ arrived with sand, the whole family headed by mom (everyone except dad ) ran joyfully around the mountain donated by the truck. Dad took a deep breath.

While dad was digging, you could play king of the hill.
The first sketch (diagram of the playground) was like this


Another scheme with the size of the playground




She was given a shine


It turned out that it was impossible to get on the hill, there was neither an elevator nor even stairs. I started making stairs, I didn’t seem to drink, apparently I don’t have to drink to get a drunken staircase.


and

From one side, we did not close the house with boards, we wanted to observe from the country window what the child was doing.
But over time, we sewed up the wall.

Having screwed the basketball ring on, I did not immediately realize that it was upside down.




The house on the hills was filled with furniture for comfort.


The ring has been turned over.


After the sandbox appeared, a mountain of toys immediately fell into it.

We urgently need to make a pantry, namely a box.

Well, how to do without a table, because on fresh air and eat, draw - a sweet thing.

After a snack, you can also strain your brains a little and play chess or, for starters, checkers in the fresh air.

In winter, it turned out that you can roll off the roof if large snowdrifts appeared below.

Now you can even ride in the winter. Take an ice cube and bigom to the top.




It remains only to hold the light, voila, now you can invite friends to a dinner party, and then admire the stars.


A piece was cut out of the sides of the sandbox, so that it would be more convenient to lick into it.

as he repeatedly beat his head against her. Beauty certainly requires sacrifice, but not on the playground)





The slide faded in the sun, for this year we have already painted it not with impregnation, but with oil paint.

After we inserted multi-colored plexiglass.
Our windows have acquired color: blue, yellow, orange - now the grass next to the hill is cheerful.

And looking through such windows the whole world becomes more fun.


Now only a loophole is missing, so that you can climb closer to the stars,

watch them.


Urgently need to make a ladder to the roof

Five years have passed, the children have grown up and we decided to update our children's complex, increase the space of the house above the sandbox.
It was necessary to shorten the height of the swing, so that the difference in the floor of the extension would not differ much from the height of the floor of the house.


Due to the fact that the height of the swing was shortened, their amplitude also decreased (for aunts it’s not scary, but for adults it’s noticeable), it’s a pity, of course, but something had to be sacrificed (we might find another place for the swing in the future).

Half of the roof was also dismantled in order to put it on new rails for a large roof.


Maybe on such a roof it will be possible to go down in the winter on an ice rink)

Part of the second half was also dismantled in order to increase the space in the future, we will insert a window into this space.

We painted the roof with new paint, this time not with wood impregnation, but with enamel, it turned out to be more durable

and already contains varnish in its basis.

We lay the floor in our annex, then lay plywood on top of the boards,

so that sand does not fall on the heads of those who swing on a swing.


We cut grooves under the glass. One glass will stay in place, and the second will move away,

so that you can climb out of the window onto the roof.




It remains to make a handle on both sides of the retractable glass so that it can be opened from both sides

On the side we fasten the support under the balcony, it is also a beam for attaching rings and a rope.

In the annex, as agreed, they hung a hammock.


On the other side of the house, we install a second beam for the future balcony and fastening rope ladder or some rocking chair

In order to make it possible to climb onto the balcony from below, we make a ladder.

Every 20 cm we make recesses for sticks. And fasten them with zip ties.


Paint the stairs a bright color





The frame of the balcony is ready, it remains to lay the floor.




Lay the floor and make a railing so that the children do not fall out of the balcony.


It will be possible to get to the balcony both by stairs from the street and from the house, through a sliding window.


It is only necessary to make a ladder or steps that can be used as shelves, so as not to clutter up the space of the house inside.







I really wanted to hang round wicker swings under the balcony so that several people could swing at once, but there are none for sale.

We found it on a Chinese site, we are waiting for it to be delivered, but for now we are waiting to decide to do something similar to a boat swing.



Steps appear from the house to climb onto the balcony from the inside.

What a pity that only two weekends for which everything is not in time.
To be continued

Our rocking chair was not very in demand, since it is interesting to rock on it with a large company, and this does not always happen.
I had to take it off and make a not-so-capacious swing out of the tire.

Now that we have in the yard funny companies we hang a big rocking chair,
and on weekdays a swing from a tire hangs.


But the other day we decided to make an elevator winch for toys or sand, so that we could lift them to the balcony with interest.



For similar slides but from less thick materials, the price ranges from 40tr and above, for example

You can also additionally make boxes for toys, a hanging table,