Job Description. Molding of fiberglass products from composite materials of a simple configuration by the contact method under the guidance of a molder of fiberglass products of a higher qualification. Manual pre-impregnation of fiberglass. the washing up hot water, drying in a drying cabinet of tools and utensils used in molding.

Must know: the procedure and methods for performing work on the molding of fiberglass products from composite materials of a simple configuration by the contact method; purpose and composition of the binder solution; types of glass fillers; the appointment of separating and decorative layers.

§ 186. Molder of fiberglass products of the 2nd category

Job Description. Forming of simple fiberglass products from composite materials by the contact method or complex products by methods: contact, gravitational, vacuum pressing with transverse stacking of fiberglass packages under the guidance of a molder of fiberglass products of a higher qualification. Preparation of mixtures for separating and decorative coatings according to a given recipe. Applying layers to the surface of the equipment manually and with a gun. Forming a simple set. Rolling of a sprayed layer onto a structure of a simple configuration under the guidance of a molder of fiberglass products of a higher qualification. Laying fiberglass on the tooling. Uniform distribution binder solution on the fiberglass by hand, avoiding air bubbles and smudges of the binder solution. Marking of simple products from glass materials according to templates and place.

Must know: the process of molding simple fiberglass products from composite materials by the contact method and molding the product; the purpose of the crimping device in vacuum molding; properties of resins, accelerators, catalysts and glass fillers; the ratio of the separating and decorative layers; types of adhesives (epoxy compounds) and rules for their use; requirements for the quality of the tooling surface; rules for determining the degree of readiness of separating and decorative layers; technical conditions for finished products; rules for reading simple drawings.

Work examples

1. Feed cans, air boxes, keel, bulkheads, fairing cases, boxes, nozzles, flat panels, pleasure boat hulls, bow, transverse baffles, corner and tee profiles, wind catchers, pleasure boat decks, etc. - contact molding.

2. Bushings, guides, shelves and corners - molding by contact method.

3. Car parts, covers, side panels, gaskets, reinforcements - contact molding.

4. Plates, a set of a simple stand, stiffeners - contact molding.

5. Sections bottom, side, deck superstructures - molding by contact method.

§ 187. Shaper of fiberglass products of the 3rd category

Job Description. Molding of complex fiberglass products from composite materials by contact and vacuum pressing, especially complex large-sized products under the guidance of a molder of fiberglass products of a higher qualification. Preparation of sealant. Sealing of impermeable joints and checking the quality of workmanship. medium difficulty metal products and other materials. Elimination of molding defects (bubbles, depressions) after removing the product from the tooling. Marking and cutting pre-impregnated glass material according to the drawings. Rolling of the sprayed layer on the design of a configuration of medium complexity. Impregnation of the laid material on a gravitational installation. Spraying of simple products. If necessary, manual preparation of binding solutions. Production accounting.

Must know: the process of molding and molding complex fiberglass products from composite materials by various methods; the device of the equipment used (stands, dies, punches); polymerization process; rules for determining the thickness of the molded product depending on the reinforced material; rules, reading complex drawings; purpose and operation principle of sputtering and gravitational installations.

Work examples

1. Banks, samples, bulkheads - spraying.

2. Propeller shafts up to 250 mm - molding.

3. Car details (casts, models), details of wings, roofs, engine compartment panels, floors - molding.

4. Parts of the cabin of diesel locomotives and electric locomotives, parts of the body of the bus "Start", boats, hulls lifeboats, decks, deckhouses, bottom sections, yawls - contact molding.

5. Door coamings, necks, shaft vestibules, bollards, sections, side deck bulkheads, foundation saturation details - molding.

6. Hulls of lifeboats, boats, yawls - molding by vacuum pressing.

7. Fairing hulls, a set of complex configurations, floors, keels, stringers, foundation beams, sections, hulls of boats, boats, foundations for main and auxiliary engines, tanks, ship furniture, deckhouses, superstructures, bottom ends, side deck superstructures, practical things, docking of sections, etc. - molding by the contact method.

§ 188. Molder of fiberglass products of the 4th category

Job Description. Forming of especially complex fiberglass products from composite materials by methods: contact, vacuum pressing and others. Application of separating decorative layers on the surface of equipment of complex configuration. Forming complex structures and products in all spatial positions. Impregnation of fiberglass packages under conditions of complex mechanization. Production of fiberglass or polymer cement equipment on wooden and gypsum blanks. Rolling and spraying of structures of complex configuration. Preparation for work and operation of gravity and spray installations. Fine-tuning products to the required dimensions according to specifications, accounting for the production of products.

Must know: technological process molding of especially complex fiberglass products from composite materials by different methods; designs and names of parts and products made of fiberglass; arrangement of serviced equipment; specifications for finished products; rules for reading especially complex drawings; the appointment of units of gravity and spray installations.

Work examples

1. Propeller shafts over 250 mm - molding.

2. Car parts, beams, cabin bases, side racks - molding.

3. Blanks for products on a perforated matrix - manufacturing.

4. Anchor, deck hawses, propeller shaft brackets, chimneys, masts, foundations for main and auxiliary engines and special installations - molding.

5. Ship hulls, sections, superstructures, docking of special installations, containers for chemical equipment, tanks for agricultural equipment for agricultural aircraft - contact molding.

6. Hulls and decks of ships - spraying and rolling.

§ 189. Molder of fiberglass products of the 5th category

Job Description. Manual molding of particularly complex and shaped products, art products with a portrait likeness, as well as multi-body or thin-walled parts made of fiberglass and composite materials with hard-to-reach parts according to a high accuracy class by spraying or contact molding according to models, shapes or templates in single or small-scale production. Laying glass fabrics, fiberglass or glass bundles on the model, impregnating them with a binder solution, conducting the process of polymerization of parts or products. If necessary - preparation of binding solutions. Adjustment and minor repairs spraying and gravity installations. Determination of the consumption of materials in the manufacture of products various methods.Assembly of individual parts of parts or products made of wood, plastics, metals. Fitting, puttying, surface cleaning; if necessary - polishing, fine-tuning to the required dimensions.

Must know: the technological process of manufacturing products from fiberglass by methods of contact, gravity, vacuum molding, spraying; molding techniques; properties of binder solutions and methods of their preparation; arrangement of units of sputtering and gravitational installations; technical conditions for finished parts and products; ways to ensure the required molding density; rules for accounting and consumption of materials.

Work examples

1. Cylinders - molding.

2. Cabin of the car - molding.

3. Water and gas tight covers - molding.

4. Decks - production by spraying.

5. Sprayers for agricultural aircraft - molding.

§ 190. Molder of fiberglass products of the 6th category

Job Description. Manual molding of experimental and experimental products from fiberglass and composite materials by various methods using special and unique molding equipment, fixtures and tools. Assembly, installation, joining and molding of complex, large-sized sections, shells. Manufacturing of standards.

Must know: the technological process of manufacturing products from fiberglass by various methods; technological scheme the process of forming products from fiberglass; design and kinematic diagrams of the serviced equipment; physical and chemical properties of the used raw materials and materials; technical requirements to quality finished products and applied materials.

Average required professional education.

We bring to your attention a typical example of a job description for a molder of parts and products, a sample of 2019/2020. A person who has secondary vocational education or primary vocational education, special training and work experience can be appointed to this position. Do not forget that each instruction of the molder of parts and products is issued on hand against receipt.

It provides typical information about the knowledge that a molder of parts and products should have. About duties, rights and responsibilities.

This material is included in the huge library of our site, which is updated daily.

1. General Provisions

1. The shaper of parts and products belongs to the category of workers.

2. A person with secondary vocational education or primary vocational education and special training and work experience of ________ years is accepted for the position of molder of parts and products.

3. The molder of parts and products is hired and dismissed by the director of the organization on the proposal of the head of production (section, workshop)

4. The shaper of parts and products must know:

a) special (professional) knowledge of the position:

- methods and modes of molding;

- types, design, dimensions of molded parts and products and their corresponding matrices, templates, rules;

- properties of materials from which parts and products are made;

— rules for the operation of equipment;

b) general knowledge of the employee of the organization:

— rules and norms of labor protection, safety measures, industrial sanitation and fire protection,

- rules for the use of personal protective equipment;

- requirements for the quality of work (services) performed, for the rational organization of labor in the workplace;

- types of marriage and ways to prevent and eliminate it;

- production signaling.

5. In his activities, the molder of parts and products is guided by:

- the legislation of the Russian Federation,

— Charter of the organization,

- orders and directives organization director,

- real job description,

— Rules of internal work schedule organizations.

6. The molder of parts and products reports directly to a worker with a higher qualification, the head of production (section, shop) and the director of the organization.

7. During the absence of the molder of parts and products (business trip, vacation, illness, etc.), his duties are performed by a person appointed by the director of the organization on the proposal of the head of production (section, workshop) in in due course which acquires the corresponding rights, duties and is responsible for the fulfillment of the duties assigned to it.

2. Job responsibilities of the molder of parts and products

The duties of the molder of parts and products are:

a) Special (professional) duties:

– Forming parts, products on a press using hot dies, on hot rules, in hydraulic presses, on machines using metal templates, crimp molds or manually.

- Giving parts the desired shape without damaging the lines and the material from which they are made.

— Compliance with the technological mode of molding.

— Checking and regulation of the molding mode.

— Ensuring the stability of the molded parts without their warping and overburning of the material.

— Equipment preparation; selection of forms, metal templates, rules in accordance with the styles and sizes of parts.

- Insertion of product parts into the mold.

- Unloading of products at the end of molding.

- Disassembly of forms.

Work examples:

1. Shafts of boots - eversion by machine or manually using special devices, with straightening them on hot rules without damaging the lines and rounding the seams.

2. Details of leather goods (cases, lids, cardboard blanks of suitcases) - molding on a press or manually on metal blocks or frames.

3. Details of saddlery and saddlery - molding on a press using matrices in a hot way or manually.

4. Blanks for home and gymnastic shoes - eversion by machine or manually using special tools and molding.

5. Blanks for model shoes - molding the heel part on the machine.

6. Leather and leather cardboard backs - molding using metal templates and pressure molds.

7. Heels made of leather, molded using metal templates and pressure molds.

8. Shoes - heel pre-molding to set the heel and sharpen the edge of the lingering edge in the heel.

9. Gloves - molding on rules with electric heating with preliminary application of paraffin or machine oil on them.

10. Technical leather products (plates, belts, disks for cotton gin rollers, etc.) - molding in hydraulic presses and manually with the selection and impregnation of blanks of products with various substances at a certain temperature.

b) General duties of an employee of the organization:

— Compliance with the Internal Labor Regulations and other local regulations of the organization,

— internal rules and norms of labor protection, safety measures, industrial sanitation and fire protection.

— Execution within employment contract orders of employees to which he is subordinate in accordance with this instruction.

– Performing work on the acceptance and delivery of shifts, cleaning and washing, disinfection of serviced equipment and communications, cleaning the workplace, fixtures, tools, as well as keeping them in good condition;

- Maintaining established technical documentation.

3. Rights of the molder of parts and products

The shaper of parts and products has the right to:

1. Submit proposals for management consideration:

– to improve the work related to the provisions of this responsibilities,

— about attraction to material and disciplinary responsibility workers who violated production and labor discipline.

2. Request from structural divisions and employees of the organization the information necessary for him to perform his duties.

3. Get acquainted with the documents that define his rights and obligations in his position, the criteria for assessing the quality of performance of official duties.

4. Get acquainted with the draft decisions of the organization's management regarding its activities.

5. Require the management of the organization to provide assistance, including the provision of organizational and technical conditions and the execution of established documents necessary for the performance of official duties.

6. Other rights established by the current labor legislation.

4. Responsibility of the molder of parts and products

The shaper of parts and products is responsible in the following cases:

1. For improper performance or non-performance of their official duties provided for by this job description - within the limits established by the labor legislation of the Russian Federation.

2. For offenses committed in the course of their activities - within the limits established by the current administrative, criminal and civil legislation of the Russian Federation.

3. For causing material damage organizations - within the limits established by the current labor and civil legislation of the Russian Federation.

Job description of the molder of parts and products - sample 2019/2020. Job Responsibilities the molder of parts and products, the rights of the molder of parts and products, the responsibility of the molder of parts and products.

Unified Tariff and Qualification Directory of Works and Occupations of Workers (ETKS). Issue #28
Approved by Order of the Ministry of Health and Social Development of the Russian Federation dated 11.01.2010 N 3

fiberglass molder

§ 185. Molder of fiberglass products of the 1st category

Job Description. Molding of fiberglass products from composite materials of a simple configuration by the contact method under the guidance of a molder of fiberglass products of a higher qualification. Preparation of the working surface of the equipment (cleaning of dirt, residues of the separating layer, binding solution, washing of the equipment). Manual pre-impregnation of fiberglass. Washing with hot water, drying tools and utensils used in molding in a drying cabinet.

Must know: the procedure and methods for performing work on the molding of fiberglass products from composite materials of a simple configuration by the contact method; purpose and composition of the binder solution; types of glass fillers; the appointment of separating and decorative layers.

§ 186. Molder of fiberglass products of the 2nd category

Job Description. Forming simple fiberglass products from composite materials by the contact method or complex products by methods: contact, gravity, vacuum pressing with transverse stacking of fiberglass packages under the guidance of a molder of fiberglass products of a higher qualification. Preparation of mixtures for separating and decorative coatings according to a given recipe. Applying layers to the surface of the equipment manually and with a gun. Forming a simple set. Rolling of the sprayed layer on a structure of a simple configuration under the guidance of a molder of fiberglass products of a higher qualification. Laying fiberglass on equipment. Uniform distribution of the binder solution on the fiberglass by hand, avoiding air bubbles and smudges of the binder solution. Marking of simple products from glass materials according to templates and in place.

Must know: the process of molding simple fiberglass products from composite materials by the contact method and molding the product; the purpose of the crimping device for vacuum forming; properties of resins, accelerators, catalysts and glass fillers; the ratio of the separating and decorative layers; types of adhesives (epoxy compounds) and rules for their use; requirements for the quality of the tooling surface; rules for determining the degree of readiness of separating and decorative layers; technical specifications for finished products; rules for reading simple drawings.

Work examples

1. Feed cans, air boxes, keel, bulkheads, fairing hulls, boxes, nozzles, flat panels, pleasure boat hulls, bow, transverse baffles, corner and tee profiles, wind catchers, pleasure boat decks, etc. - contact molding.

2. Bushings, guides, shelves and corners - contact molding.

3. Car parts, covers, side panels, gaskets, reinforcements - contact molding.

4. Plates, a set of a simple rack, stiffeners - contact molding.

5. Bottom, side, deck superstructure sections - contact molding.

§ 187. Shaper of fiberglass products of the 3rd category

Job Description. Molding of complex fiberglass products from composite materials by contact and vacuum pressing, especially complex large-sized products under the guidance of a molder of fiberglass products of higher qualification. Preparation of sealant. Sealing of impervious joints and checking the quality of workmanship. Molding of medium complexity products made of metal and other materials. Elimination of molding defects (bubbles, depressions) after removing the product from the tooling. Marking and cutting pre-impregnated glass material according to the drawings. Rolling of the sprayed layer on the structure of the configuration of medium complexity. Impregnation of the laid material in a gravity plant. Spraying of simple products. If necessary - preparation of binding solutions manually. Production accounting.

Must know: the process of molding and molding complex fiberglass products from composite materials by various methods; the device of the used equipment (stands, matrices, punches); polymerization process; rules for determining the thickness of the molded product depending on the material being reinforced; rules, reading complex drawings; purpose and principle of operation of sputtering and gravitational installations.

Work examples

1. Banks, samples, bulkheads - spraying.

2. Propeller shafts up to 250 mm - molding.

3. Car parts (casts, models), wing parts, roofs, engine compartment panels, floors - molding.

4. Cabin parts for diesel locomotives and electric locomotives, body parts for the "Start" bus, boats, lifeboat hulls, decks, wheelhouses, bottom sections, yawls - contact molding.

5. Door coamings, necks, shaft vestibules, bollards, sections, side deck bulkheads, foundation saturation details - molding.

6. Hulls of lifeboats, boats, yawls - molding by vacuum pressing.

7. Fairing hulls, a set of complex configuration, floors, keel, stringers, foundation beams, sections, hulls of boats, boats, foundations for main and auxiliary engines, tanks, ship furniture, deckhouses, superstructures, bottom ends, side deck superstructures, practical things , docking of sections, etc. - molding by the contact method.

§ 188. Molder of fiberglass products of the 4th category

Job Description. Formation of particularly complex fiberglass products from composite materials by methods: contact, vacuum pressing and others. Application of separating decorative layers on the surface of the equipment of complex configuration. Forming of complex structures and products in all spatial positions. Impregnation of fiberglass packages in conditions of complex mechanization. Production of fiberglass or polymer cement equipment on wooden and gypsum blanks. Rolling and spraying of structures of complex configuration. Preparation for work and work on gravity and spray installations. Fine-tuning products to the required dimensions according to specifications, accounting for the production of products.

Must know: the technological process of molding especially complex fiberglass products from composite materials by different methods; designs and names of parts and products made of fiberglass; arrangement of serviced equipment; technical specifications for finished products; rules for reading especially complex drawings; assignment of units of gravitational and sputtering installations.

Work examples

1. Propeller shafts over 250 mm - molding.

2. Details of automobiles, beams, cabins of the bases, racks lateral - molding.

3. Blanks for products on a perforated matrix - manufacturing.

4. Anchor, deck hawses, propeller shaft brackets, chimneys, masts, foundations for main and auxiliary engines and special installations - molding.

5. Ship hulls, sections, superstructures, docking of special installations, chemical equipment tanks, agricultural equipment tanks for agricultural aircraft - contact molding.

6. Hulls and decks of ships - spraying and rolling.

§ 189. Molder of fiberglass products of the 5th category

Job Description. Manual molding of particularly complex and shaped products, art products with a portrait likeness, as well as multi-body or thin-walled parts made of fiberglass and composite materials with hard-to-reach parts according to a high accuracy class by spraying or contact molding according to models, shapes or templates in single or small-scale production. Laying glass fabrics, fiberglass or glass bundles on the model, impregnating them with a binder solution, conducting the polymerization process of parts or products. If necessary - preparation of binder solutions. Adjustment and minor repairs of sputtering and gravitational installations. Determination of the consumption of materials in the manufacture of products by various methods. Assembly of individual parts of parts or products made of wood, plastics, metals. Fitting, puttying, cleaning surfaces; if necessary - polishing, fine-tuning to the required dimensions.

Must know: technological process of manufacturing products from fiberglass by methods of contact, gravity, vacuum molding, spraying; molding techniques; properties of binder solutions and methods of their preparation; arrangement of units of sputtering and gravitational installations; technical conditions for finished parts and products; ways to ensure the required molding density; rules for accounting and consumption of materials.

Work examples

1. Cylinders - molding.

2. Cabin of the car - molding.

3. Water and gas tight covers - molding.

4. Decks - production by spraying.

5. Sprayers for agricultural aircraft - molding.

§ 190. Molder of fiberglass products of the 6th category

Job Description. Manual molding of experimental and experimental products from fiberglass and composite materials by various methods using special and unique molding equipment, fixtures and tools. Assembly, installation, docking during the formation of complex, large-sized sections, shells. Manufacturing of standards.

Must know: technological process of manufacturing products from fiberglass by various methods; technological scheme of the process of molding products from fiberglass; design and kinematic diagrams of the serviced equipment; physical and chemical properties of the used raw materials and materials; technical requirements for the quality of finished products and materials used.

Requires secondary vocational education.

We always have on our website a large number of fresh current vacancies. Use filters to quickly search by parameters.

For successful employment, it is desirable to have a specialized education, as well as to have necessary qualities and work skills. First of all, you need to carefully study the requirements of employers in the chosen specialty, then start writing a resume.

You should not send your resume to all companies at the same time. Choose suitable vacancies, focusing on your qualifications and work experience. We list the most significant skills for employers that you need to successfully work as a molder of fiberglass products in Moscow:

Top 7 Key Skills You Need to Get a Job

Also quite often in vacancies there are the following requirements: carpentry work, concrete work and result orientation.

When preparing for an interview, use this information as a checklist. This will help you not only to please the recruiter, but also to get the desired job!

Analysis of vacancies in Moscow

According to the results of the analysis of vacancies published on our website, the indicated starting salary, on average, is - 45,507. The average maximum income level (specified "salary to") is 56,610. Keep in mind that these figures are statistics. The actual salary during employment can vary greatly depending on many factors:

• Your previous work experience, education
• Type of employment, work schedule
• Company size, industry, brand, etc.

Salary depending on the experience of the applicant

Unified Tariff and Qualification Directory of Works and Professions of Workers (ETKS), 2019
Issue #28 ETKS
The issue was approved by the Order of the Ministry of Health and Social Development of the Russian Federation dated January 11, 2010 N 3

fiberglass molder

§ 185. Molder of fiberglass products of the 1st category

Job Description. Molding of fiberglass products from composite materials of a simple configuration by the contact method under the guidance of a molder of fiberglass products of a higher qualification. Preparation of the working surface of the equipment (cleaning of dirt, residues of the separating layer, binding solution, washing of the equipment). Manual pre-impregnation of fiberglass. Washing with hot water, drying tools and utensils used in molding in a drying cabinet.

Must know: the procedure and methods for performing work on the molding of fiberglass products from composite materials of a simple configuration by the contact method; purpose and composition of the binder solution; types of glass fillers; the appointment of separating and decorative layers.

§ 186. Molder of fiberglass products of the 2nd category

Job Description. Forming simple fiberglass products from composite materials by the contact method or complex products by methods: contact, gravity, vacuum pressing with transverse stacking of fiberglass packages under the guidance of a molder of fiberglass products of a higher qualification. Preparation of mixtures for separating and decorative coatings according to a given recipe. Applying layers to the surface of the equipment manually and with a gun. Forming a simple set. Rolling of the sprayed layer on a structure of a simple configuration under the guidance of a molder of fiberglass products of a higher qualification. Laying fiberglass on equipment. Uniform distribution of the binder solution on the fiberglass by hand, avoiding air bubbles and smudges of the binder solution. Marking of simple products from glass materials according to templates and in place.

Must know: the process of molding simple fiberglass products from composite materials by the contact method and molding the product; the purpose of the crimping device for vacuum forming; properties of resins, accelerators, catalysts and glass fillers; the ratio of the separating and decorative layers; types of adhesives (epoxy compounds) and rules for their use; requirements for the quality of the tooling surface; rules for determining the degree of readiness of separating and decorative layers; technical specifications for finished products; rules for reading simple drawings.

Work examples

1. Feed cans, air boxes, keel, bulkheads, fairing hulls, boxes, nozzles, flat panels, pleasure boat hulls, bow, transverse baffles, corner and tee profiles, wind catchers, pleasure boat decks, etc. - contact molding.

2. Bushings, guides, shelves and corners - contact molding.

3. Car parts, covers, side panels, gaskets, reinforcements - contact molding.

4. Plates, a set of a simple rack, stiffeners - contact molding.

5. Bottom, side, deck superstructure sections - contact molding.

§ 187. Shaper of fiberglass products of the 3rd category

Job Description. Molding of complex fiberglass products from composite materials by contact and vacuum pressing, especially complex large-sized products under the guidance of a molder of fiberglass products of higher qualification. Preparation of sealant. Sealing of impervious joints and checking the quality of workmanship. Molding of medium complexity products made of metal and other materials. Elimination of molding defects (bubbles, depressions) after removing the product from the tooling. Marking and cutting pre-impregnated glass material according to the drawings. Rolling of the sprayed layer on the structure of the configuration of medium complexity. Impregnation of the laid material in a gravity plant. Spraying of simple products. If necessary - preparation of binding solutions manually. Production accounting.

Must know: the process of molding and molding complex fiberglass products from composite materials by various methods; the device of the used equipment (stands, matrices, punches); polymerization process; rules for determining the thickness of the molded product depending on the material being reinforced; rules, reading complex drawings; purpose and principle of operation of sputtering and gravitational installations.

Work examples

1. Banks, samples, bulkheads - spraying.

2. Propeller shafts up to 250 mm - molding.

3. Car parts (casts, models), wing parts, roofs, engine compartment panels, floors - molding.

4. Cabin parts for diesel locomotives and electric locomotives, body parts for the "Start" bus, boats, lifeboat hulls, decks, wheelhouses, bottom sections, yawls - contact molding.

5. Door coamings, necks, shaft vestibules, bollards, sections, side deck bulkheads, foundation saturation details - molding.

6. Hulls of lifeboats, boats, yawls - molding by vacuum pressing.

7. Fairing hulls, a set of complex configuration, floors, keel, stringers, foundation beams, sections, hulls of boats, boats, foundations for main and auxiliary engines, tanks, ship furniture, deckhouses, superstructures, bottom ends, side deck superstructures, practical things , docking of sections, etc. - molding by the contact method.

§ 188. Molder of fiberglass products of the 4th category

Job Description. Formation of particularly complex fiberglass products from composite materials by methods: contact, vacuum pressing and others. Application of separating decorative layers on the surface of the equipment of complex configuration. Forming of complex structures and products in all spatial positions. Impregnation of fiberglass packages in conditions of complex mechanization. Production of fiberglass or polymer cement equipment on wooden and gypsum blanks. Rolling and spraying of structures of complex configuration. Preparation for work and work on gravity and spray installations. Fine-tuning products to the required dimensions according to specifications, accounting for the production of products.

Must know: the technological process of molding especially complex fiberglass products from composite materials by different methods; designs and names of parts and products made of fiberglass; arrangement of serviced equipment; technical specifications for finished products; rules for reading especially complex drawings; assignment of units of gravitational and sputtering installations.

Work examples

1. Propeller shafts over 250 mm - molding.

2. Details of automobiles, beams, cabins of the bases, racks lateral - molding.

3. Blanks for products on a perforated matrix - manufacturing.

4. Anchor, deck hawses, propeller shaft brackets, chimneys, masts, foundations for main and auxiliary engines and special installations - molding.

5. Ship hulls, sections, superstructures, docking of special installations, chemical equipment tanks, agricultural equipment tanks for agricultural aircraft - contact molding.

6. Hulls and decks of ships - spraying and rolling.

§ 189. Molder of fiberglass products of the 5th category

Job Description. Manual molding of particularly complex and shaped products, art products with a portrait likeness, as well as multi-body or thin-walled parts made of fiberglass and composite materials with hard-to-reach parts according to a high accuracy class by spraying or contact molding according to models, shapes or templates in single or small-scale production. Laying glass fabrics, fiberglass or glass bundles on the model, impregnating them with a binder solution, conducting the polymerization process of parts or products. If necessary - preparation of binder solutions. Adjustment and minor repairs of sputtering and gravitational installations. Determination of the consumption of materials in the manufacture of products by various methods. Assembly of individual parts of parts or products made of wood, plastics, metals. Fitting, puttying, cleaning surfaces; if necessary - polishing, fine-tuning to the required dimensions.

Must know: technological process of manufacturing products from fiberglass by methods of contact, gravity, vacuum molding, spraying; molding techniques; properties of binder solutions and methods of their preparation; arrangement of units of sputtering and gravitational installations; technical conditions for finished parts and products; ways to ensure the required molding density; rules for accounting and consumption of materials.

Work examples

1. Cylinders - molding.

2. Cabin of the car - molding.

3. Water and gas tight covers - molding.

4. Decks - production by spraying.

5. Sprayers for agricultural aircraft - molding.

§ 190. Molder of fiberglass products of the 6th category

Job Description. Manual molding of experimental and experimental products from fiberglass and composite materials by various methods using special and unique molding equipment, fixtures and tools. Assembly, installation, docking during the formation of complex, large-sized sections, shells. Manufacturing of standards.

Must know: technological process of manufacturing products from fiberglass by various methods; technological scheme of the process of molding products from fiberglass; design and kinematic diagrams of the serviced equipment; physical and chemical properties of the used raw materials and materials; technical requirements for the quality of finished products and materials used.

Requires secondary vocational education.