APPROVE:

________________________

[Job title]

________________________

________________________

[Name of company]

________________/[FULL NAME.]/

"____" ____________ 20__

JOB DESCRIPTION

Repairman

1. General Provisions

1.1. This job description defines and regulates the powers, functional and job duties, rights and responsibilities of a repairman [Name of organization in the genitive case] (hereinafter referred to as the Company).

1.2. The repairman is appointed to the position and dismissed from the position in accordance with the procedure established by the current labor legislation by order of the head of the Company.

1.3. The repairman belongs to the category of workers and reports to [position title of the immediate supervisor in the dative case] of the Company:

• Deputy Head of ACH,
• Deputy Head of Engineering,
• deputy head of construction
• head of the economic department,
• head of the technical department,
• head of the construction department.

1.4. A person with a secondary education and appropriate training in the specialty is appointed to the position of a repairman.

1.5. The repairman must know:

• arrangement of repaired equipment, units and machines;
• machine regulation rules;
• ways to eliminate defects in the process of repair, assembly and testing of equipment, units and machines;
• device, purpose and rules for the use of used control and measuring instruments;
• design of universal and special devices;
• methods of marking and processing simple various parts;
• system of admissions and landings;
• quality and roughness parameters;
• properties of acid-resistant and other alloys;
• the main provisions of preventive maintenance of equipment;
• design features of the repaired equipment, units and machines;
• technical conditions for repair, assembly, testing and regulation and for the correct installation of equipment, units and machines;
• technological process of repair, assembly and installation of equipment; rules for testing equipment for static and dynamic balancing of machines;
• geometric constructions with complex markup;
• methods for determining premature wear of parts;
• ways to restore and harden worn parts and apply a protective coating.

1.6. In his work, the repairman is guided by:

• normative acts and methodological materials on the issues of the work performed;
• internal labor regulations;
• orders and orders of the head of the Company and the immediate supervisor;
• this job description;
• rules on labor protection, safety precautions, industrial sanitation and fire protection.

1.7. During the temporary absence of a repairman, his duties are assigned to [deputy position].

2. Functional responsibilities

The mechanic-repairman is obliged to carry out the following labor functions:

2.1. Implementation of repair work.

2.2. Disassembly, repair, assembly and testing of components and mechanisms.

2.3. Repair, installation, dismantling, testing, regulation, adjustment of equipment, units and machines and delivery after repair.

2.4. Locksmith processing of parts and assemblies.

2.5. Manufacture of complex devices for repair and installation.

2.6. Preparation of defective repair reports.

2.7. Performing rigging work using lifting and transport mechanisms and special devices.

2.8. Identification and elimination of defects during the operation of the equipment and when checking during the repair process.

2.9. Accuracy and load testing of repaired equipment.

3. Rights

The repairman has the right to:

3.1. Give assignments to subordinate employees, tasks on a range of issues included in his functional duties.

3.2. Supervise the fulfillment of production tasks, the timely execution of individual orders by subordinate employees.

3.3. Request and receive the necessary materials and documents related to the issues of its activities and the activities of employees subordinate to him.

3.4. Interact with other services of the enterprise on production and other issues that are part of its functional responsibilities.

3.5. Get acquainted with the draft decisions of the enterprise's management regarding the activities of the Division.

3.6. To propose to the head of the proposal to improve the work related to the duties provided for in this Job Description.

3.7. Submit proposals for the consideration of the head of the proposal on the promotion of distinguished employees, the imposition of penalties on violators of production and labor discipline.

3.8. Report to the manager about all identified violations and shortcomings in connection with the work performed.

4. Responsibility and performance evaluation

The repairman bears administrative, disciplinary and material (and in some cases provided for by the legislation of the Russian Federation, also criminal) responsibility for:

4.1.1. Non-fulfillment or improper fulfillment of official instructions of the immediate supervisor.

4.1.2. Failure to perform or improper performance of their labor functions and assigned tasks.

4.1.3. Unlawful use of the granted official powers, as well as their use for personal purposes.

4.1.4. Inaccurate information about the status of the work entrusted to him.

4.1.5. Failure to take measures to suppress the identified violations of safety regulations, fire and other rules that pose a threat to the activities of the enterprise and its employees.

4.1.6. Failure to enforce labor discipline.

4.2. Evaluation of the work of a repairman is carried out:

4.2.1. Direct supervisor - regularly, in the course of the daily implementation by the employee of his labor functions.

4.2.2. Attestation Commission of the enterprise - periodically, but at least once every two years based on the documented results of the work for the evaluation period.

4.3. The main criterion for evaluating the work of a repairman is the quality, completeness and timeliness of his performance of the tasks provided for in this instruction.

5. Working conditions

5.1. The work schedule of a repairman is determined in accordance with the internal labor regulations established by the Company.

5.2. In connection with the production need, a repairman may go on business trips (including local ones).

Acquainted with the instruction ___________ / ____________ / "____" _______ 20__

Unified Tariff and Qualification Directory of Works and Professions of Workers (ETKS), 2019
Part No. 1 of issue No. 36 ETKS
The issue was approved by the Decree of the State Committee of the USSR on Labor and Social Affairs and the All-Union Central Council of Trade Unions of June 7, 1984 N 171 / 10-109
(As amended by the Decrees of the USSR State Committee for Labor, the Secretariat of the All-Union Central Council of Trade Unions of 03.02.1988 N 51 / 3-69, of 14.08.1990 N 325 / 15-27, the Ministry of Labor of the Russian Federation of 21.11.1994 N 70, of 31.07.1995 N 43)

Mechanic for the repair of technological installations

§ 46. Locksmith for the repair of technological installations of the 2nd category

Job Description. Disassembly, repair, assembly and testing of simple components and mechanisms of machines, apparatus, pipelines, fittings. Repair of simple installations, units and machines, as well as of medium complexity under the guidance of a more highly qualified locksmith. Locksmith processing of parts according to 12 - 14 qualifications (5 - 7 accuracy classes). Washing, cleaning and lubricating parts. Marking and drilling holes on flanges. Straightening, filing and cutting threads on pipes. Manufacture of simple fixtures for assembly and installation of repaired equipment.

Must know: device, purpose and principle of operation of individual devices and units of equipment being repaired; operating conditions of the serviced equipment; basic locksmithing techniques; general rules for welding and soldering; rules for testing pipelines of small diameters; basic concepts of tolerances and landings, qualifications, classes of accuracy and cleanliness of processing; purpose and rules for the use of devices and tools; pipe marking techniques; drawing elements; rules for the use of oils, detergents and lubricants.

Work examples

1. Manhole covers of machines and devices - removal and installation.

2. Protections - removal and installation.

3. Gaskets - production.

4. Heat exchangers of the "pipe in pipe" type - disassembly.

5. Pipes of the cooling and lubrication system - cleaning.

6. Gas nozzles - revision.

§ 47. Mechanic for the repair of technological installations of the 3rd category

Job Description. Dismantling, repair, assembly and testing of the average complexity of units and mechanisms of machines, apparatus, pipelines, fittings. Repair of medium complexity installations, assemblies and machines, as well as complex ones under the guidance of a more highly qualified locksmith. Locksmith processing of parts according to 11 - 12 qualifications (4 - 5 accuracy classes). Disassembly and assembly of piping devices, pumps, compressors. Manufacture of medium complexity fixtures for assembly and installation of repaired equipment.

Must know: device and principle of operation of the repaired equipment, fittings; specifications for pipes; profile steel, fixing materials; fundamentals of welding; properties of welded metals; rules for laying pipelines; equipment operation rules; the basic technological scheme and the scheme of communications of the serviced installation; tolerances and landings; quality and roughness parameters.

Work examples

1. Low pressure fittings - removal, repair, installation.

2. Compressors - disassembly and removal of valves, seals, oil deflectors, crossheads, bearings, valve covers and cylinders.

3. Oil pumps, lubricators - dismantling, repair.

4. Piston, plunger, centrifugal and gear pumps disassembly, repair.

5. Oil seals - stuffing.

6. Pipelines and devices of the cooling and lubrication system of compressors and pumps - disassembly.

7. Furnace pipes, plates and inter-plate space of columns, tubes and annular space of heat exchangers, tubes of refrigerator condensers - cleaning from coke and deposits.

§ 48. Locksmith for the repair of technological installations of the 4th category

Job Description. Dismantling, repair, assembly of complex installations, machines, devices, pipelines and fittings using lifting mechanisms. Locksmith processing of parts according to 7 - 10 qualifications (2 - 3 accuracy classes). Removal and installation of working and control safety valves from capacitive equipment. Testing, adjustment and delivery of equipment after repair. Manufacture of complex fixtures for assembly and installation of repair equipment. Preparation of defective repair reports.

Must know: purpose, arrangement of complex equipment; technical conditions for repair, testing, adjustment and delivery of repaired equipment; basics of preventive maintenance; system of tolerances and landings, qualifications and roughness parameters; methods of marking and processing simple various parts; arrangement of load-lifting mechanisms and rules for their use; basics of rigging; rules for checking repaired and assembled units and devices.

Work examples

1. Air coolers - disassembly of the gearbox.

2. Column type devices - repair, assembly of internal devices, removal and installation of covers, heads.

3. Heat exchangers - assembly.

4. Granulators, crystallizers, mixers, filters - disassembly, repair, assembly.

5. Piston compressors - disassembly, repair and assembly of cylinders, crankshaft, crosshead assembly, valves, pistons.

6. Centrifugal compressors - disassembly of the rotor, repair of bearings and gear couplings.

7. Centrifugal, double-casing and multi-stage pumps with more than four impellers - disassembly.

8. Tubular furnaces - replacement of pipes, doubles.

9. Reactors - replacement of the lantern, removal of heads, removal and installation of the zone thermocouple pocket, assembly of the seal assembly and coupling joints.

10. Reducers - repair, assembly, adjustment.

§ 49. Mechanic for the repair of technological installations of the 5th category

Job Description. Disassembly, repair, assembly of particularly complex installations of machines, devices, units, pipelines, fittings using mechanisms and delivery after repair. Locksmith processing of parts and assemblies according to 6 - 7 qualifications (1 - 2 accuracy classes). Dismantling, repair and assembly of components and equipment in conditions of intense and dense landings. Technical certification of equipment.

Must know: device and design features of complex equipment; technological sequence and organization of labor during the repair, assembly, installation of equipment; all types of materials used in the repair; methods for determining premature wear of parts; static and dynamic balancing of machines; geometric constructions with complex markup; ways to restore worn parts; methods of repair of equipment and apparatus operating under high pressure.

Work examples

1. Apparatus - repair of the body (not requiring heat treatment), checking the plates for bubbling.

2. Shut-off, safety and control valves - disassembly, repair, grinding, assembly and adjustment.

3. Ventilation ducts - assembly.

4. Blowers, blowers and superchargers - repair, testing.

5. Compressors, pumps - scraping of bearing shells and other machine parts, repair of safety and check valves.

6. Piston compressors - adjustment and commissioning.

7. Gas engine compressors - repair.

8. Condensers-refrigerators - removal and installation of sections.

9. Ball mills, roller mills, crushers, screens, smoke exhausters, granulators - overhaul, testing, commissioning.

10. Centrifugal, double-casing and multi-stage pumps with more than four impellers - repair, assembly, commissioning.

11. Tube furnaces - control, rejection of pipes.

12. Reactors - repair.

13. Heat exchangers (raw materials) of hydrotreatment, catalytic reforming, hydrocracking and other over 200 atm repairs.

14. Centrifuges - repair.

§ 50. Mechanic for the repair of technological installations of the 6th category

Job Description. Repair, installation, dismantling, assembly, testing and adjustment of especially complex unique installations, devices, machines and units using mechanisms. Identification and elimination of defects during the operation of the equipment and when checking during the repair process. Accuracy and load testing of repaired equipment.

Must know: design features of especially complex equipment; technical conditions for the repair, testing and commissioning of especially complex unique equipment; metal technology; ways to restore especially complex and critical nodes; allowable loads on operating parts, components and mechanisms of equipment; equipment maintenance and repair systems.

Work examples

1. Air coolers - assembly and alignment of the gearbox.

2. Drum vacuum filter - replacement of intermediate bearing shells, repair of the faceplate, adjustment of the distributor head, commissioning.

3. Granulators - sorting of parts, repair and assembly of the drive head, shtober, alignment of the main drive electric motor, alignment of the knife support.

4. Centrifugal compressors - repair of labyrinth seals and rotor; rotor balancing, alignment, assembly.

5. Gas engine compressors - adjustment, adjustment, testing.

6. Waste heat boilers - overhaul, hydraulic tests. Lens seals for high pressure pipelines (700 - 2500 atm) - repair.

7. Tubular furnaces - test (hydraulic or pneumatic) of the coil.

8. Reactors - hull repair, hydraulic testing.

9. Catalytic cracking reactors - replacement of the stuffing box sleeve, lens compensator and straight section of the pressure riser, the glass of the separation plate, side pipes and the collector of the outlet manifold.

10. Reactors for catalytic reforming and hydrotreatment - repair and assembly of a glass, switchgears, pocket of zone thermocouples.

11. Reactors with a stirrer - installation of a stirrer and bottoms in a high-pressure reactor, alignment and assembly of coupling joints, hydraulic testing.

12. Catalytic cracking regenerators - replacement of the coil, defective sections, distribution grid, production of an air box, replacement of defective sections.

13. Planetary gearboxes and with complex tooth profile - assembly.

14. Heat exchangers (raw materials) of hydrotreating, catalytic reforming, hydrocracking and other units over 200 atm assembly, testing.

15. High pressure pipelines for any liquids and gases, as well as pipelines of reactor blocks of catalytic reforming, hydrotreatment, hydrocracking units - repair, assembly.

16. Steam turbines - checking the gap between the blades, housing, rotor; repair and establishment of gaps in diaphragm seals, stuffing box seals, in thrust and thrust bearings, alignment, adjustment.

17. Turbochargers - overhaul and delivery.

18. Centrifuges - pressing clutch couplings, shaft alignment, pressing out and assembly of the mechanical seal housing, disassembly and assembly of probes, scraping of bearings, bushings, sorting of parts, commissioning.

§ 50a. Locksmith for the repair of technological installations of the 7th category

(introduced by the Decree of the Ministry of Labor of the Russian Federation of July 31, 1995 N 43)

Job Description. Adjustment and complex adjustment of complex technological complexes, combined and large-capacity plants. Maintenance and diagnostics, including vibration diagnostics of machinery during operation and during repairs. Load testing and tuning of particularly complex machinery and refurbished equipment. Maintenance of technical documentation for the operation and repair of equipment, participation in the launch of complex technological complexes and installations. Management of lower-skilled workers.

Must know: ways to adjust complex technological complexes and installations; design features of especially complex equipment; technical documentation for the repair, testing and commissioning of especially complex equipment; metal technology; system of admissions and landings; modern methods of restoring parts and assemblies - plasma spraying, the use of metal-layers and others; a system of scheduled preventive maintenance of equipment of oil refineries.

1. General safety requirements

1.1. Persons at least 18 years of age who have passed a preliminary medical examination upon admission to work, as well as:

• induction training;
• fire safety briefing;
• initial briefing at the workplace;
• electrical safety training in the workplace

1.2. A mechanic for the repair of technological installations must:

• undergo repeated training on labor safety at the workplace at least every three months;
• undergo unscheduled and targeted briefings;
• pass a knowledge test on the rules for the design and safe operation of lifting mechanisms;
• undergo a sanitary medical examination in accordance with the order of the Ministry of Health of the Russian Federation No. 90 of 03.14.96 and the order of the Ministry of Railways of 07.07.1987 No. 23 c;
• perform only the work that is part of his duties;
• .use safe work practices;
• comply with the requirements of prohibitory, warning, indicative and prescriptive signs and inscriptions and signals given by train compilers, vehicle drivers;
• be extremely careful in traffic areas.

1.3 The mechanic for the repair of technological installations must know:

• the impact on a person of dangerous and harmful production factors that arise during work;
• general arrangement of technological installations;
• alarms installed on the PPS and the location of the devices for their supply;
• rules for the design and safe operation of lifting mechanisms;
• requirements for industrial sanitation, electrical safety and fire safety;
• location of first aid kits;
  • internal labor regulations established at the enterprise;
  • the requirements of this instruction, instructions on fire safety measures, instructions on electrical safety;
  • appointment of personal protective equipment;
  • instructions for signaling on the railways of the Russian Federation;
  • regulation on the discipline of railway workers;
  • rules and regulations on labor protection, safety and industrial sanitation;
  • instructions for maintenance of wagon equipment;
  • be able to provide first aid to victims, use fire extinguishing equipment, call the fire brigade in the event of a fire.

1.3. A mechanic for the repair of technological installations in his work should be guided by the requirements:

this instruction;

Federal Law "Transport Regulations for Railways of the Russian Federation";

Rules for the technical operation of railways of the Russian Federation (PTE);

Instructions for signaling on the railways of the Russian Federation;

Regulations on the discipline of employees of railway transport of the Russian Federation.

1.4. During work, the following hazards may affect the mechanic for the repair of technological installations.

Falling objects and tools.

High or low temperature.

Increased humidity and air mobility of the working area.

Increased noise and vibration levels

Moving vehicles, mechanisms, rolling stock.

Insufficient lighting at night.

1.5. The mechanic for the repair of technological installations must use the following PPE:

Cotton suit, acid-proof gloves, boots, goggles.

In winter additionally:

The jacket is insulated.

1.6. The mechanic for the repair of technological installations must comply with the following fire safety requirements:

Smoking only in designated areas;

Do not approach with an open flame to a gas welding machine, gas cylinders of flammable liquids, gaseous liquids and spray booths;

Do not touch oxygen cylinders with hands contaminated with oil;

Know and be able to use primary fire extinguishing equipment.

1.7. Personal clothing and overalls must be stored separately in lockers and dressing rooms. It is prohibited to take work clothes outside the enterprise.

1.8 Food should be taken only in canteens, buffets or specially designated rooms with appropriate equipment. Before eating, wash your hands thoroughly with soap

1.9. When on a railroad track, a locksmith must comply with the following requirements:

Railway tracks should pass only in the established places, marked with signs "Service Passage", pass along the track only along the side of the road;

Cross the tracks only at a right angle, after making sure that there is no locomotive moving at a dangerous distance in this place;

Cross the track occupied by the rolling stock only using the transitional platforms of the wagons;

Bypass groups of wagons no closer than 5 m from the automatic coupler;

Pass between uncoupled wagons if the distance between them is at least 10 m;

When leaving the car, hold on to the handrails and position yourself facing the car, having previously inspected the place of exit and made sure that the handrails and footboards are in good condition, as well as that there is no rolling stock on the adjacent track;

Pay attention to traffic lights;

Do not cross paths in front of a moving train;

Sit on the steps of the wagons and get off them while moving;

Crawl under the wagons;

Stepping on electrical wires and cables;

Touch broken wires;

Climb onto the roof of the car under the contact wire;

Approach closer than 2 m to the current-carrying parts of the contact network.

1.10. When leaving the track from the heating room, as well as from buildings that impair the visibility of the track, you must first make sure that there is no train moving along it.

1.11. For non-compliance with the safety requirements set forth in this manual, the mechanic is responsible in accordance with applicable law.

2. Safety requirements before starting work

2.1. Before starting work, the mechanic for the repair of technological installations must:

Put on overalls and special footwear according to the norms, put them in order;

Fill the loose ends of the clothes so that they do not hang down;

Set the sequence of operations;

Inspect your workplace, check the condition of racks and pallets;

Check the availability and serviceability of tools, measuring instruments, templates, as well as their presence on racks and repair installations of spare parts and materials;

Check the operation of the electric hoist, the serviceability of the limit switches;

Check the availability of fire fighting equipment;

Check the serviceability of ladders, bridges, ensure their reliable installation;

Make sure the illumination of the workplaces is reliable.

3. Safety requirements during operation

3.1 Each machine, machine tool, unit, stand must have a technical passport. Non-standard equipment must have circuit diagrams. New or installed equipment should be put into operation only after it has been accepted by a commission chaired by the chief or chief engineer.

3.2. Equipment intended for the repair of wagons, their units and parts must be kept in good condition, placed in the places provided for by the technological process, not interfere with work, free passage and passage.

3.3. All process equipment must have operating instructions containing safety requirements for maintenance.

3.4. Technological equipment that can serve as a source of danger to workers, the surfaces of fences and other protective devices, as well as fire equipment, must be painted in signal colors.

3.5. Electrical equipment, as well as equipment and mechanisms that may be energized must be grounded.

3.6. Hoisting mechanisms, lifting devices (slings, traverses, grabs) must be operated and tested in accordance with the Rules for the Construction and Safe Operation of Hoisting Cranes.

3.7. Heat-consuming installations, pipelines of steam and hot water must be operated in accordance with the Rules for the operation of heat-consuming installations.

3.8. Equipment (machines, mechanisms, presses) must be installed on the bases, carefully leveled and fixed. It is necessary to have convenient access to the equipment for inspection, lubrication and maintenance.

3.9. Vices on workbenches must be in good working order, stable and have a height convenient for work.

3.10. Jacks must have a designation of carrying capacity, inventory number, date of the next test. Periodic technical inspection of jacks should be carried out at least once every 12 months. Routine maintenance of jacks should be carried out every 10 days.

3.11. After any type of repair of the car-repair installation, running-in and testing of all fixtures and devices under working loads, as well as adjustment of all components and parts, must be carried out. After a scheduled repair, the commissioning of the car repair plant must be carried out by the site foreman.

3.12. Washing machines used in the preparation of wagons for repair for external and internal washing of wagons, as well as for washing bogies, wheelsets, bearings and other wagon parts, must be equipped with devices for cleaning, reuse and disposal of wastewater, mechanized removal of sludge and residues garbage.

3.13. The management of the depot and technical support must provide the workers with serviceable, properly sharpened tools. Defective tools must be removed and replaced.

3.14. Devices should be easy to use, easy to install, fixed in position and easy to remove. The work of devices should not create an excessive strain of physical forces for the employee, the use of special means and should not be accompanied by increased levels of noise and vibration.

3.15. Manual power tools must be in good working order, and grinders must have protective covers.

3.16. Hand tools and devices for daily use must be secured for individual or team use.

3.17. To carry the tool, if required by the conditions of work, each worker should be given serviceable hand boxes or bags.

3.18. Paint sprayers, hoses, handles of brushes, spatulas, knives and other painting tools should be cleaned and washed from the remnants of paints and varnishes at the end of the shift and handed over to a pantry or other specially equipped place.

3.19. When using ladders and ladders, they must be taken into account, numbered and have signs indicating that they belong to a particular site. In the depot and technical equipment, a register of ladders and ladders should be kept, indicating the timing of their testing.

3.20. Special mobile carts used for painting work must be kept in good working order and ensure the safety of work. Platforms for mobile carts must be fenced on three sides with railings not less than 1 m high with transverse or longitudinal braces and have a solid perimeter fence not less than 150 mm above the floor. Mobile platform trolleys when not in use must be securely fastened.

3.21. Rinsing water during the washing of wagons, bogies, wheelsets, bearings and other parts must be collected and neutralized.

4. Safety requirements in emergency situations

4.1. During the repair of technological installations in the depot, the following emergencies may occur:

Ignition, which can lead to a fire;

Fall of a wagon raised on jacks or mounted on staves.

4.2. In the event of an emergency, the locksmith is obliged to stop work, immediately inform the foreman and then follow his commands.

4.3. When eliminating an emergency, it is necessary to act in accordance with the approved plan for eliminating accidents.

4.4. In the event of a fire that could lead to an explosion, you must:

Notify the fire brigade immediately;

Proceed to extinguish the fire;

Organize the evacuation of people;

Arrange a fire department meeting.

4.5. When electrical equipment catches fire, use only carbon dioxide or powder fire extinguishers.

4.6. In case of injury or illness, the mechanic for the repair of technological installations must stop working, notify the master and contact the first-aid post.

5. Safety requirements at the end of work

5.1. Upon completion of the work, the locksmith must:

Tidy up the workplace;

Fold the tool, inventory and fixtures in a specially designated place;

Collect used cleaning material in metal boxes with tight-fitting lids;

Take off your overalls and put them in the dressing room closet.

5.2. If necessary, hand over the contaminated overalls for washing.

5.3. After work or in cases of contamination of body parts, take a shower.

5.4. The locksmith must inform the foreman about all violations of the production process.

Search Options

Job: RTO mechanic 6th category in Sosnovy Bor, 0 vacancies

The average salary for the profession locksmith 6th category in Sosnovy Bor: 0 rubles

Sorry, no suitable vacancies found. Try changing your request.

Jobs

Jobs 6th category rto locksmith vacancy 6th category rto locksmith in Sosnovy Bor. Vacancy 6th category mechanic from a direct employer in Sosnovy Bor job advertisements for a 6th category mechanic from Sosnovy Bor, vacancies for recruitment agencies in Sosnovy Bor, looking for a job as a 6th category mechanic from recruitment agencies and from direct employers, vacancies for a 6th category mouth mechanic with and without work experience experience in the Leningrad region. The site of announcements about part-time jobs and jobs Avito Sosnovy Bor job vacancies locksmith RTO 6th category from direct employers.

Work in Sosnovy Bor

Site work Avito Sosnovy Bor work fresh vacancies locksmith RTO 6th category. On our site you can find a highly paid job as a locksmith of the 6th category. Look for a job as a locksmith of the 6th category in Sosnovy Bor, view vacancies on our job site - a job aggregator in Sosnovy Bor in the Leningrad region.

Avito vacancies Sosnovy Bor

Jobs as a 6th category mechanic at the site in Sosnovy Bor, vacancies for a 6th category as a mechanic from direct employers in Sosnovy Bor. Vacancies in Sosnovy Bor without work experience and highly paid with work experience. Vacancies locksmith RTO 6th category for women.

Information on the device, purpose, as well as the principle by which individual devices and components, units and equipment intended for repair work operate. Under what conditions it is necessary to service technological installations. What basic techniques should be followed in the implementation of locksmith activities. Have a general knowledge of welding and soldering. According to what rules are tested pipelines that differ in small diameters. A mechanic for the repair of technological installations must have basic concepts regarding tolerances, landings, qualifications, according to what principles the accuracy and frequency of processing are classified. Have an idea about everything related to fixtures, tools, as well as their purpose and operating rules. What are the rules for marking pipes? Rules to be followed when using oils, greases and detergents. Master the basic elements related to drawing. Mandatory compliance with the production, job description, as well as the rules that relate to the internal labor regulations. Have basic knowledge of economics, economic state policy, features of the current stage of development, development prospects, which production plan the enterprise, workshop, team adheres to. What modern methods should be followed to organize your work and workplace. Know the necessary list of safety requirements, including industrial sanitation, as well as fire safety.

The scope of duties of a mechanic for the repair of technological installations of the third category includes:

Measures for disassembly, repair, assembly, as well as testing of everything that relates to simple components and machine mechanisms, this applies to apparatus, pipelines and fittings. The above specialist must repair everything related to simple installations, units and machines, he must carry out repair work that is equated to an average and advanced level of complexity. The repair activities of a locksmith for the repair of technological installations of the third category are led by a locksmith who has a higher qualification. Also, the duties include work on the metalworking of parts, which is characterized by the accuracy of manufacturing parts of at least 4-5 classes (for 11-12 qualifications). Carrying out activities for flushing, cleaning, and lubricating the elements of the installation. The specialist must be able to mark, followed by drilling a hole in the flange. Be able to perform work on straightening, filing, and cutting threads on the pipe. Engage in simple fixtures, namely, their manufacture, which are designed to assemble and mount repairable equipment.

The required amount of knowledge of a mechanic for the repair of technological installations of the third category:

Information on the device, purpose, as well as the principle by which individual devices and components, assemblies and equipment intended for repair work, including fittings, operate. Have an accurate knowledge of pipe specifications, in addition to profile steel and fastening materials. Be proficient in welding, know everything about the properties of materials intended for welding. According to what list of rules are the installations and other equipment operated. According to what principles and technologies the pipeline is laid. Own a basic technological diagram, including a diagram that relates to the communications of the installation intended for maintenance. Know everything about tolerances, qualifications, fits and roughness parameters.

The scope of duties of a mechanic for the repair of technological installations of the fourth category includes:

Measures for disassembly, repair, assembly, as well as testing of everything related to complex installations, machines, pipelines, apparatus, fittings, when lifting mechanisms are used. The duties of a locksmith for the repair of technological installations of the fourth category include work on locksmith processing of parts, which is characterized by the accuracy of manufacturing parts of at least 2-3 classes (for 7-10 qualifications). Carry out measures for the removal and installation of working and control safety valves from installations that are capacitive. Engage in testing, adjustment and delivery of equipment for further operation after repairs have been made. Engage in the manufacture of complex fixtures for the assembly and installation of installations that are intended for repair work. Engage in the preparation of defective statements for repair activities.

The required amount of knowledge of a mechanic for the repair of technological installations of the fourth category:

What is the purpose of and how complex equipment is arranged. Know everything about the technical conditions for repairs, tests, adjustments, as well as the subsequent delivery of installations that have been repaired. Know everything about preventive maintenance. Know everything about tolerances, fits, qualifications, as well as roughness parameters. Know how markings are applied, as well as how to properly process parts that are considered simple. How to properly check the units and devices that have been under repair.