Homemade gates in the garage. Swing gates for the garage do-it-yourself: production and installation

To date, a variety of garage gate designs has been developed and successfully implemented. Your attention is offered a description of the most popular varieties of portal systems, as well as guidance on self-assembly and installation of the swollen gate - the easiest in the manufacture of the design, with the arrangement of which almost every beginner master will be able to cope. Having gained experience, you can collect more complex systems.

In such gates, the sash drives towards the system from the guide and rollers. The gate can be installed outside and inside the garage.

Advantages and disadvantages

Among the main advantages of the retractable gate should be noted such moments as:

The main disadvantage is the fact that it is possible to establish such a gate only on a garage with a wide facade. Its width should be at least such that the departing sash can fully fit on it.

Such a gate can be made and mounted independently. The flaps themselves are made practically on the same principle as the sash of ordinary swing gates. Differences are present only at the installation phase - guides and rollers are used instead of loops.

Very convenient option. Most often there are systems in which the sash rises up and fixes over the opening. Galvanized steel is usually used for the manufacture of the gate. It is often found and structures from aluminum - such flaps weigh noticeably less than their steel analogues.

Advantages and disadvantages

The advantages are as follows:

However, such a gate can be used except for equipping a private garage located on a secure individual area. Lifting structures, especially made of aluminum, have relatively low rigidity, which does not allow them to provide the required garage protection.

Such gates have a rather complicated design. For their independent manufacture, you need to have a good engineering experience and own special knowledge necessary to select a suitable counterway and the installation of related mechanisms.

A beginner master may except to try to independently install the finished lifting gate of the factory assembly. This is done simply in accordance with the manufacturer's instructions.

The design is assembled from several horizontal sections interconnected using hinge loops. The extreme sections are equipped with rollers moving on guide boards. The guides themselves bend so that when opening the gate, it is unhindered to fit under the garage ceiling.

The design is characterized by sufficiently high rates of reliability and rigidity. Inside each section, as a rule, insulation is already present, which additionally increases the heat and noise insulating properties of the gate.

Advantages and disadvantages

Benefits:

The disadvantages are relatively small anti-svliness and high price.

Make such a gate will not work independently. Of course, you can try, but it is not a fact that the homemade design will work correctly. In addition, a lot of money and time will go to the manufacture of sections.

Most often consist of two sash. At the heart of the gate is a metal frame. You can use a sandwich panels, steel sheets and other suitable materials to be used.

For greater convenience in the sash, you can cut the wicket.

Advantages and disadvantages

Benefits:

The main disadvantage is the need to have sufficient free space before the garage to open the gate. It delivers special inconvenience in winter - to open the gate, you will have to pre-clear the track in front of them from snow.

Swing gates are the most simple in the manufacture. It is in their favor that it is recommended to give preference to novice masters.

Molding Gate Manufacturing Guide

Pre-planly plan the dimensions of the future gate in accordance with the dimming dimensions for entering the garage and buy the required amount of materials. For greater amenities, make a drawing or at least an elemental sketch.

First stage - fastener frame

Start with the manufacture of the carrier frame. Source material - metal corner. The frame will consist of an external and internal support frame.

First step.Measure the opening.

The second step.Cut the corner on the workpiece of the desired size for the manufacture of the outer frame. Spread the resulting items on the plane, align them horizontally and align the corners.

To regulate the horizontal, use lining, corners check with a carbon. With its absence, you can simply extort the diagonal. Immediately correct any deviations.

Thus, you need to lay out the blanks in the form of a future outer frame.

Third step.Cook the carrier frame. Its outdoor side should be as smooth and completely smooth as possible, otherwise the gate will lay down enough to it. To ensure the required smoothness, glorify the welding seams using an ordinary grinder.

Fourth step. Ride in the corners of the design of the vertical cutting of the corner. They will provide the necessary rigidity of the frame, i.e. they will allow it to remain geometrically unchanged.

Second Stage - Frame

Start the framework of the frame. In the future, you attach the finishing metal canvas to this frame. The frame itself can be made from a metal profile with a cross section of 6x2 cm.

First step. Put the frame on a suitable smooth surface "face" up.

The second step. Insert the guides into the carrier frame. Each side of the design thoroughly align.

Third step. Provide a 15-20-millimeter gap between the carrier frame and the inner portable frame. To do this, use the liners. Thanks to this gap in the future, the flaps will be able to move without difficulty.

Fourth step. Make sure the framework of the frame corners and finally weld the profiles.

Third Stage - Testing

Be the most attentive and neat at this stage. The aesthetic qualities and a number of the most important functional properties of the finished design are fully dependent on the correctness of the trim.

First step. Cut a steel sheet in size of garage sash. At the same time, the left flap of the gate should be on the right with the 1-2 centimeter coach - take into account this moment.

The second step. Temporarily secure sheets on the frame. To do this, grab them at several points below.

Third step. Cut the cover of the right portal sash by 10-20 mm (you need for the allen, mentioned earlier).

Fourth stage. Finally weld sheets to the frame. First, weld the material at the corners and in the center of each box, and then fix the perimeter. Thanks to this, sheets will not move during work. After completing the welding, the angular and central fastening points must be cut off.

Fourth Stage - Loops

Hinged loops are best to buy.

We weld the lower hinge element to the carrier frame. Top element weld to the outer flap. To strengthen the compound you can use a curved metal strip. It must be applied to the top of the mounted loop and to the barny sash.

Additionally, the stiffness of the loop fixation can be enhanced by welding to the inside of the fitting of the reinforcement liner.

Fifth stage - castles and constipation

The gates under consideration are most often equipped with mounted or mortise locks. Additionally, it is recommended to install stoppers and high-quality goals. These products will allow closing the garage doors from the inside.

Pins stoppers without problems are made on their own. For the manufacture of such a design, leak into the ground either half the garage cut pipe, and immerse the metal rod inside it - the movable element of the stopper. Prut needs to be trained through the loop pre-made in the sash. Watch that the pipe is not clogged with snow and different mud.

Castles also require timely and competent care. Protect your gate locks from moisture exposure, especially in winter. Periodically lubricate the castles with oil.

Sixth Stage - Painting

The paint layer will provide additional protection of the metal canvas from corrosion and other destruction.

Cover the metal of the primer, let it dry, and then apply a double layer of selected paint to finish metal surfaces.

Any painting works do either outdoors or indoors with good ventilation!

Seventh Stage - Installation

First step. Install the outer and inner element of the portal frame. Fixation performs to the slopes of the portion opening with the help of metal pins of about 18 cm long.

The second step. Cut the protruding edges of metal pins, elaper them and carefully stuck with the help of a grinder so that they do not interfere with the gate to close. If desired, you can paint pins.

Third step. While the inner and outer part of the frame using jumpers (metal plates) in 40 mm. The jumpers weld with a step of about 50-60 cm.

Fourth stage. Sleep sash. If you wish, you can finish your garage automation. It is very convenient - you do not have to constantly break and plan the sash on your own.

Video - Production and installation of garage gates

Eighth Stage - Warming

In the absence of high-quality thermal insulation through the gate, up to 50-60% of heat will leave. If you plan to use a garage during the cold season and are going to equip it with any kind of heating, be sure to solve the issue with arrangement of insulation.

To do this, mounce on the inner surface of the ductal flaps with a crate of wooden bars. Pagting of the elements is individually as composed of the width of the insulation plates. For thermal insulation, it is recommended to use Minvatu and other materials based on it.

Before laying the insulation, lock the polyethylene film over the crates. Place the insulation in the cells of the crate. Insulation, lay the most tight, without cracks and gaps. For most regions of the 5-centimeter thickness of the insulation layer more than enough. Heat insulation cover the vapor insulation film. On top of the crate with insulation, type the lining or other facing material.

In independent design and installation of the garage doors, there is nothing superpower. You only need to follow the instructions and save attentive at every stage of work. Having understood in the order of arrangement of simple swing gates, you can independently build more complex structures.

Good job!

Video - Gate for garage with your own hands

Video - automatic gate swing in the garage for boats

Among the masses of those people who decide to put the gates on the site, there will be those who decide to make the gate alone. Let's analyze the positive and negative points in the installation of the garage gate on their own.

Pluses of self-installation

• saving funds, this is one probably from the fundamental factors of choice
• ability to use materials at your discretion
• unique design, because you are developing it yourself
• new knowledge and use of them in practice

Cons Montage Gate on their own

• for a long time of manufacture
• there is a risk of not finish work
• lack of knowledge negatively affects the quality of your garage gates
• buying diverse and additional unforeseen expenses
• help friends, one difficult to mount the gate
• garbage and waste production on your site
• for the manufacture you need enough space

Gate options

• sectional
• lifting
• sliding
• rolled
• swing

Swing gates are simpler in manufacturing and installation.

Welding and carpentry tools

• Metal square.
• Six garage loops.
• Sheet metal.
• Metal rod.
• Bulgarian.
• Grinding machine.
• Drilling machine.
• Roulette.
• Level.
• Metal profile.
• Drill.
• Metal profile.
• Set of screws.
• Screwdriver.
• Profile pipes
• Drills set.
• Insulation
• Profile pipes
• Plywood.
• The presence of electricity.
• Welding machine.
• Brushes or rollers for painting.
• Foam assembly.
• Primer.
• Paint.

Stage of performance

Select sizes for future gates. There are no tricks. We look at the building and size of your car.

Gate frame. To do this, we will need even and large playground. It should not be garbage and rubble. You can, for example, in the yard will sit down. We make a backup of bricks, boards, concrete blocks. We need to raise work above the floor, for the convenience of the work.

We take the level and align our framework. Rehend to this stage seriously. Nobody wants to have a garage gate curves, and if the skew will, then this emboss will be very difficult to correct.

Weld up pipes, be especially careful to skews.

We begin to produce the target of the gate. Garage gate makers must be in the same plane with a frame. For the convenience of work with the stems we will weld temporary supports from the bottom of the sash. It will be necessary to take 12 supports. And 2 short plates and 4 long on the frame pipes.

We are engaged in welding work and grind carefully angles.

Install metal sheets. On a flat site, cut off the sheet marked in advance. Then the sheet must be attached to the samples and cook with them. Little Lifehak: Put the sheets at such a height so that you can be comfortable. Free the approaches to sheets.

Installation of loops. This is the final stage of working with the welding machine. We weld the loops around the perimeter of your design in those places where we will be attached to the walls of the garage.

Coloring and decoration of the gate. One of the favorite stages of a large family. Children will gladly decorate your gate with various drawings. If you are a fan of conciseness and poor colors, you can paint in silver, black.

It is important to use the primer, to apply before the start of staining and let it dry. Choose paints for metal, learn the instructions for them.

Choose the castle. Now there are many garage locks on the market. It is important to buy a castle in advance to prepare the installation groin for it.

Explore the manufacturer's instructions. There are even modern electronic locks. Make a canopy over the lock, will help the castle not to be wounded in the wintful weather.

Warm the garage door. The climate, as you yourself know, harsh in Russia, there are cold winters. And in some areas the temperature is constantly holding down on minus fifty. So it is advisable to insulate the gate.

Most often use economical cheap foam. There are special insulation, many analogues and substitutes. There is even an option to make warm electric doors.

If there is time and effort to make the gate yourself, then do it. Now there is a lot of information on any types of work. Invite friends and family to participate in the manufacture. And then every time driving his car into the garage, you will be proud of the fruit of your creation.

Photo garage do it yourself

From the quality of the garage gate, the safety of the car and comfort of stay in the room depends, so they should be made with full responsibility. There are several gate options: they differ in the first place the opening mechanism. Modern models are quite complex, require special skills and tools for mounting, but install the classic swing garage garage do it with their own hands and without the experience of such work.

Selecting a garage type type

Self assembly gate - this is a great way to save on the construction of the garage. However, before proceeding with the task, it is worth considering the existing types of designs and determine the most appropriate. The choice depends on many factors, and if the optimal models with a complex mechanism are optimal, it makes sense to refer to specialists - the wrong installation of them can lead to various problems with the functioning of the structure.

Sliding gates

Retractable gates are one wide sash that drives off the Welcome when opening.

Guides are attached to the frame of the structure, which drives the sash, and the cattors holding it in the open position. Depending on the design of the guide, the gate can be suspended, console and rail; Options are varying, convenience of operation, the number of parts and the complexity of installation.

Like other types of garage gates, retractable designs can be manual and automatic. In the second case, the electric drive is connected to the frame, which can be stationary or remote.

Although it is easy to make such a garage to the garage, they are rarely chosen, since they have more flaws than advantages. The main plus is the savings of the space outside, but there is a lot of space inside the room - it should be very wide. Because of this, the retractable models are often used outside, embeding into the fencing of the site. These designs are applied at industrial facilities in the hangars.

The disadvantages also include the need to install a reinforced frame that can keep the suspended sliding sash having large dimensions and mass than in the case of encouraging options.

It is important to constantly follow the rollers so that the design does not jin.

Rotary structures

The sash of the gate of the lifting-turning type rotates around its horizontal axis, rises to the ceiling and hangs the plafhmy over the opening. The mechanism is very convenient and reliable, space is saved and outside, and inside the garage. However, such a goal has features due to which their use may not be the best solution.

The main design is solid sash. To raise it to the ceiling it was easier, it is necessary to reduce its mass as much as possible. This affects the spectrum of possible manufacturing materials: most often the frame is made of steel tubes of small cross section, but an aluminum profile can also be used. For the sheat, a thin galvanized metal is applied. Because of this, thermal insulation characteristics are reduced, which leads to increased energy costs for the heating of the garage.

If the design is made of aluminum, its protective ability is significantly deteriorated - the frame rigidity is not enough to withstand significant physical exertion. Therefore, lifting-turning structures are used primarily on fencing areas equipped with additional security levels. They also find use within warehouses.

To establish a model of this type with your own hands is very difficult - the assembly of the lifting mechanism requires special knowledge and skills.

Lifting-section and rolled mechanisms

The lifting-section gate is similar to the lifting-turning on the principle of action, but differ in design: instead of a solid sash, a movable web is used, consisting of a lamellae interconnected. Because of this, such a gate is considered a variety of blinds.

The frame consists of two parts: One is installed around the perimeter of the opening, the second is under the garage ceiling. It is going from the guide profile. Each slave lamel has rollers on the side of the side, with which the canvas moves along the guides. An electric drive is connected to the top of the frame that is connected to the cable. When the gate is activated, the engine pulls the canvas, lifting it to the ceiling.

A canvas are made from sandwich panels, thereby ensuring sufficient stiffness of the design and high-quality heat insulation of the garage. The gate can have a different configuration and dimensions. The canvas necessarily should rise to the ceiling - in some models, the sash drives to the side. Thanks to the flexibility of lamella connections, it allows you to make a sliding gate in the garage with a small square.

The rolled gate is an analogue of lifting-sectional structures, characterized in that the canvas does not move away, and wounds on the shaft. This saves space, but the sash in this case is made from thin, narrow lamellae and has lower thermal insulating and protective characteristics.

The designs of this type can be assembled independently, but all components, including lamellas and sash, will have to be purchased in the finished form. Companies supplying such products usually provide a service of assembling a gate, so it makes no sense to carry out work. In addition, not knowing the nuances, it is easy to allow errors when installing the parts of the gate, which will lead to their incorrect functioning.

Swing doors

Classic swing gate Usually consist of two hinge flaps. An ordinary entrance door is embedded in one of the webs. The flaps consist of a frame that is trimmed with sheet metal, sandwich panels, wood and other materials. Between the outer and the inner surface, the thermal insulation material can be laid.

This is the most economical material, and thanks to the simple design, install such a gate with their own hands will not be problems. In addition, they provide the most reliable garage protection.

Thus, in the absence of skills, the assembly of complex lifting and retracting mechanisms and working with electronics, the best option will be a simple swing gate.

If the convenience of use and saving space is important, it is worth paying attention to more advanced options.

Project development

The quality of the gate depends on how correctly the sizes of their elements are chosen and how accurately details are adjacent to each other, so before making a garage doodle with their own hands, you need to make a project. Despite the simplicity of swing design, it consists of a variety of parts, and without drawings or sketches in the work will be easily mistaken.

First of all, you need to decide on the size of the gate. To make it convenient to use, the total width of the sash should be 0.6 m larger than the width of the car. Most often, the size of the gate is selected in the range of 2-4 m; If the width exceeds 5 m, the construction operation will be difficult. The height of the flaps is also calculated on the basis of the dimensions of the car.

The design of the swollen gates includes a frame that is fixed around the perimeter of the garage opening, and two sash, one of which is built in the wicket - they are fixed on the frame with the hinge. The frame is made of steel corner with a width of 65 mm. For the sash frame, it is better to choose a profile pipe with a rectangular cross section; Its size can be any.

The outer surface of the flaps is sifted with a sheet steel 3 mm thick. From the inside the frame can be seen by boards, plywood. It is done if the gate is insulated. The number of materials is calculated on the basis of the square of the flaps.

Tools and materials

To collect a high-quality swap design yourself, the skills of handling the basic construction tool, as well as the ability to use the welding machine. It is impossible to connect the details with fasteners: in this case, the reliability of the design will be insufficient. Self-tapping screws only when installing the inner covering of the sash.

It will take the next set of tools.:

• manual welding machine - newcomer It is better to choose an inverter for arc welding, it is easier for them;
• the electric generator of sufficient power for welding, if there is no possibility of connecting to the power grid;
• bulgarian with a set of circles for cutting and grinding;
• sander;
• drill with metal drills;
• screwdriver;
• brush or roller;
• measuring tools - Roulette, Set of metal squares, level.

A set of necessary materials depends on the characteristics of the project. In general, it will be necessary to prepare:

• steel rectangular profile or corners for the manufacture of the gate frame, frame and ribs of stiffeners;
• 6 reinforced welded loops;
• sheet metal;
• steel bars;
• a set of screws;
• wooden bars;
• liquid Nails;
• insulation - mineral wool or foam, a small amount of foil polyethylene;
• sheet material for internal sheat;
• primer and paint;
• mounting foam.

Additionally, you should purchase a lock, constipation, door handles and other fittings.

Instructions for manufacture

The gate is made in the following order: first frame and frame are boiled, then the sash is trimmed, after that the design is installed on the garage opening. Welding work for greater convenience should be conducted on a flat horizontal surface. When the gate is fixed, an internal cover is carried out, installation of accessories and decorative finish.

Assembling Rama

The frame is assembled at the same scheme, regardless of the number, size of the sash and the presence of gate. It will consist of two identical rectangles - external and internal, which are connected by reinforcement or strips of sheet steel.

The order of work is:

1. Corner or steel profile is cut with a grinder. The ends of the segments are trimmed at an angle of 45 °.
2. Segments are laid out on a flat surface. If there is no suitable location, you can use bricks or other supports. It is important that the details lie in the same plane - it should be checked using a level at each stage of operation. After welding, the mistakes allowed will be very difficult to fix.
3. The frame elements are welded in the corners. If this part of the gate is made from the corner, the details can be welded the mustache, imposing the shelves to each other.
4. The angles are additionally strengthened by trimming reinforcement to increase the stiffness of the structure.
5. Fasteners made of sheet metal are welded to the inner part of the frame.
6. Welded seams are grouped - the frame should be perfectly smooth on the outside, so that the sashs are lightened tight.

It is important to think in advance how to fix the frame on the wall of the garage. There are two options: to make steel beds next to the opening and weld fasteners to them, or drill in the last holes for fastening by anchors.

Welding and covering of sash

The frame of the flaps is going in the same way as the frame - by welding the segments of the profile among themselves. To work it is convenient, you should put a ready-made frame on a flat surface and put the framework details into it. Sizes of sewns must be less than 15-20 mm to provide a gap - this will simplify the operation of the gate.

Unlike the frame, the framework of the sash must have additional ribbies. To save them, they can be made of pipes with a smaller cross section. Ribs can be diagonal or vertical, in the second case they pass in the middle of each sash.

After welding and grinding frame sash are sash. This is done as follows:

1. Sheet metal is cut into the size of the sash. After welding, it should go beyond the edges of the frame for 15-20 mm (according to the size of the gap).
2. One of the flaps is cut into so as to be the second for 10-20 mm - so the elements of the gate will fit tightly to each other.
3. Sheets are welded to the frame. First, it should be copped the parts in the corners and in the center, then connect the metal around the perimeter of the sash.

After the completion of welding to the goal is attached loops. The bottom of the part is welded to the frame, the top - to the sash. For better loop fixation, it is possible to strengthen the liners from the reinforcement, which are welded to the inside of each product.

Mounting design

In the opening of the gate, a fully welded design is installed; Because of its large mass at this stage, you will need an assistant. It is recommended to install in parallel with the construction of the walls of the garage.

Before putting the gate in the opening, it is necessary to connect the external and inner parts of the frame. For this, strips of sheet steel width 40 mm are used; The length of them should be equal to the thickness of the wall of the garage. Installed parts in 60 cm increments all over the perimeter of the frame.

If the gate is installed in the finished garage, the best option will be anchor mount. If the wall is still built, it should be lit into the segments of the reinforcement, to which the inner part of the frame is then welded.

After the installation is completed only install accessories. To ensure minimal security, loops and mounted castle. More complex products are installed according to the instructions from the manufacturer. Fully finished gates are covered with primer and paint. From the inside the sash can be insulated with mineral wool, fixing it with liquid nails, and if the foam is used, it should be laid on the wood bars crate.

Knowing how to make the gate to the garage with your own hands, you can collect the design of any configuration. Instead of metal for the manufacture of a frame, the use of wood is allowed. Sewing the gate can also be any similar sheet material.

Stand out among their fellow some advantages. First, they are made from whole webwhich can be made very resistant to hacking attempts. Secondly, rotary gate In open form, it does not occupy so much space in space before the garage, how much do swinging.

Thirdly, with sufficient experience and the ability to work with sensors and electric drives, they can be made automaticopening when pressed on the console.

Additional, but, nevertheless, the important advantage of the garage lifting gates made by their own hands are great options for choosing decor - The gate can be seen by clapboard, plastic panels, steel and many others.

Lifting gates to the garage - dimensions:

But besides the advantages you need to remember disadvantages. The main minus of the lifting rotary gates is that in the open position they are installed horizontally under the ceiling, taking 20 cm From the height of the opening, which in some situations may cause inconvenience (let's say when you are trying to enter the garage on a high SUV).

The essential disadvantage of the solid canvas is that it will be necessary to change a separate item during its damage, but the whole design is immediately. In addition, it can be sufficiently heavy, which involves heavy loads on the frame and the lifting system.

The rising garage gates have another minus: they can only be used in rectangular openings. But here it should be remembered that garages with arched or other shapes are extremely rare.

The lifting and rotary doors in the garage do it yourself - blueprints:

We buy everything you need

Now it's time to take a handle, several sheets of paper and make a list of all that is necessary for manufacture lifting gates On the garage with your own hands. All this can be purchased in the nearest construction department store, because there should be no big problems with the search for materials and tools.

So for homemade lifting gates We need to go to the garage:

1. Wooden timber cross section 100x100 and 120x80 mm. They can be replaced by a steel profile of comparative strength.
2. Corners 40x40. and thick 4 mm.
3. Channel 40x80 mm..
4. Lickey material: thick boards 25 mm, Profile or plastic panels.
5. Steel rod diameter 8 mm.
6. Two springs with inner diameter 30 mm.
7. Anchor bolts and self-tapping screws.

As for the tools, then, first of all, we need a roulette, a corner and a level for careful control that the size of the garage lifting garage is correct.

For work S. metal We need a corner machine (it is better known as Bulgarian) and the welding machine. In addition, we need to cut wooden bar. And to carry out other work with him, and, it means that we need an electric jigsaw, drill and screwdriver. Well, what is the repair without a hammer, screwdrivers and wrench?

Pre-planning

How to do lifting gate. In the garage yourself? Together with the tape measure and the level should go to the mind to find out the size of the lifting homemade garage gates. This is a very responsible step, which depends on whether your work will be successful.

After that, you can take a sheet of paper and start making it yourself blueprints Garage lifting gates. So, they will consist of solid canvases, opening, frames under the ceiling and mobile mechanisms.

First of all, you need to carefully measure drawing The lifting gates in the garage are all sizes so that there are no different inconsistencies and problems in the future in the future. We useful to make a plan with several species, including isometry.

If at this stage you have difficulties - try to find comrade with experience in compiling drawings And, even better, the manufacture of the gate. Made with their own hands blueprints Lifting gates in the garage? Now it's time to proceed to action!

Garage garage lifting her own hands - blueprints:

Lifting garage do it yourself: Step-by-step instructions

How to do rotary gate on the garage do it yourself?

1. First of all, we need to equip opening. Vertical supports from the 120x80mm timer should be inserted into the garage (if it is already flooded) or land (if not yet) for 20-30 millimeters, for greater reliability, the depth can be increased. To the walls of the garage and vertical and horizontal beams will be attached using anchor bolts.
2. We collect the frame under ceiling. To do this, from the opening at a distance of about the length of the gate, you should set a horizontal beam for guides. It is important that it was parallel to the horizontal beam of the opening and at the entire length was the same in height, the battles are unacceptable.
3. Of two metal corners with welding going guide railThrough which the roller mounted on the canvas will be moved. It is necessary to carefully control the distances between the vertices of the corners when assembling. Two such rails must be attached to the upper beams, for this you can use metal accessories and screws.
4. Made by frame of canvas. For it, you can take a wooden bar, or metal corners, welded in a square profile. For better durability of the canvas to the main frame, you can breed (or attach) transverse or diagonal beams. Do not forget about the rollers in the upper part of the design.
5. Using fastener, you need enter the cloth Selected material.
6. This item of the manufacture of lifting-turning gates is very important, he should pay much attention. Using corners and fasteners, you need to do movable brackets on both supporting beams. They should attach the levers of their channels, which will push the cloth up.
7. To hold the gate in the open position needed springs. They are attached to the bottom of the supports, to the bracket and to the tip of the chapellor. When lifting the spring, the spring is compressed and does not allow spontaneous lowering: to close the gate it will be necessary to make a considerable force. It will not be superfluous to equip the fastening of the spring to the bracket and the chapeller with the tension regulator.
8. Finishing stage making a gate - Installation of all elements, insulation of the canvas and fastening on the lining of the decorative coating.

Lifting gates in the garage do it yourself (from the profile):

Further rotary gate You can improve the garage by adding the ability to automatically open and closing. To do this, an electrical drive, a signal receiver and a control panel will be required. As the latter, you can apply a key chain for automotive alarms, and as a drive - either a reverse winch, or a power winder mechanism.

Do not forget to install reliable shut-off systemwhich will protect your garage from illegal penetration. If you often come here and you do not need to raise the cloth every time, then it can make a cut in it.

In addition, in the canvas, you can make inserts from glass or any other transmitted material, so you will save on the garage in the bright time of the day.

As you can see, do it yourself rotary gate The garage is not so difficult, the main thing is not even good skills of working with metal and wood, but careful planning and observance of garage sizes lifting gates. If everything was done correctly - such a gate will serve you a very long service.

Useful video

Watch the video about how to make rotary gate For the garage do it yourself:

The construction of the garage gate do it with their own hands not only allows you to save on the payment of services of professionals, but also save the car from damage or hijacking. The product should have an attractive appearance, be resistant to temperature and humidity drops. Buy garage doors easier, but more pleasant to make them with your own hands.

How to make a garage gate alone

For many vehicle owners, the creation of garages is out of position. Build a foundation, roof and wall walls should be for protection against bad weather, and mount the gate - from foreign visitors. Since the product provides the safety of an expensive tool, then the house has more free space for storing other items.

Before making the gate to the garage with your own hands, you will need to evaluate all the features of the relief. Since the width of the carrier flaps can be 2.5-3 m, their discovery should always be unhindered. Additional place during the operation of the garage is not required only if the lifting gate is installed.

Installation of the lifting gates provides greater owners more freedom for maneuvers at the entrance to the garage. Services for the manufacture of such structures are offered by many companies, but each owner of a car having all the necessary skills, by the forces to make the gate alone.

If the installation of the design is scheduled in the old doorway, it will take into account its size. Made by the opening can be reduced or enlarged on the basis of the following recommendations:

• the minimum distance from the side of the car to the rack of the gate should be 30 cm;
• distance can be increased if the room is provided for a larger car;
• the height of the design of the structure is usually at least 2 m, the optimal parameter size is 2.1-2.4 m;
• steel sheets must have a thickness of at least 3 mm.

If you plan to install a garage gate with your own hands, then you need to prepare design drawings in advance. They will be required in the assembly process as the main document, which is a data source to calculate the required amount of materials. Drawings provide maximum accuracy that allows you to adjust portable flaps to the door to the door.

This will eliminate the appearance of moisture indoors.

The manufacture of the gate begins with the preparation of the necessary tools and familiarization with the design of the design of a certain type. Varieties of the gate depend on the way they are opening. Their assembly is carried out in a specific sequence.

The design of the swollen gate has 2 swallowing flaps. It provides a free entry of the vehicle through the doorway. The opening angle of the sash is usually at least 90 °. As a result, the risk of damage to the side surface of the body is reduced.

If it is impossible to install a gate with sash, you should choose more expensive models that have a lifting mechanism. The manufacture of the garage gate of the swing type requires the preparation of instruments and materials. The structure includes sash (1 or 2), frames, loops and other elements.

The production of swing garage gates is carried out from the following types of materials:

• profile;
• sheet metal;
• valves;
• metal corners;
• castle.

From the tools should be prepared:

• bulgarian;
• welding machine;
• roulette;
• corolnic;
• building level.

It is simple to produce the swollen gate, because large physical costs are not required. All materials can be bought in retail stores of the appropriate specialization. In the process of performing work, it is important to comply with the design technology, which includes several stages. The gates themselves must consist of the following elements:

• frame;
• canvas;
• framework;
• loops;
• fasteners.

Initially, the dimensions of the opening should be measured, after that cut off the blanks. All items must be laid on a flat surface and exhibited at the construction level. You will need to check the horizontal parts to align the corners.

Then the design can be welded with a welding machine. This stage requires the preparation of the outer side of the frame, which is even and smooth, which depends on the density of the arrogance of the gate. For this purpose, you can make grinding of seams after welding.

How to make a gate frame

At the first stage, the frame assembly, which is carried out using a welding machine based on the elementary skills of using this tool. The prepared profile is cut by a grinder to separate parts whose parameters must match.

The frame design includes 2 rectangular elements that are connected to each other during the assembly process. To manufacture the frame parts yourself, you need to cut the corner into separate elements, the length of which corresponds to the level of height and width of the future gate. Every measure accounts for 4 pcs. Of 8 pieces of metal profile 60x20.

To create frame elements, it is necessary to cut 8 pieces of a corner, taking into account the width and height of the structure (for each measurement should be 4 pcs.). The material is folded on an ideally smooth surface with the subsequent formation of rectangles. After measuring the diagonals and angles, all the elements of the walls of the wall will be perfect to match each other.

Next, it will be necessary to make welding frame for all carrier flaps. The solidity of the corners of the frame should be checked by the coal. Between the frame and sections, it is not necessary to leave too much clearance so that it allowed to open the doors with convenience. The seams are a vulnerable place subject to corrosion and destruction to the greatest extent.

Do not neglect the processing of welded connections.

They must be cleared so that the surface becomes perfectly smooth. Future sash must be tightly closed. This will ensure the quality of the external and inner frame.

To securely connect the elements, it will be necessary to use crossbars from the rod or metal strips. If you use a rod, you can prepare a row of holes in the wall. They should drive the reinforcement rods of the required length, welding them to the frame elements. The welding of connecting parts is carried out on top of the edges of the opening. Strengthen sheet metal to the frame, it is necessary so that the web to the left could go to the frame of the flap on the right to 2 cm.

Installation of loops and dodov with your own hands

For a more durable fastening, the loops will require reinforcement rods that need to be acadeced from the inside. The technology of cooking loops is as follows:

• the lower part is attached to the frame;
• the upper part is to the sash outside.

Inside the connection is strengthened by a folding tab. To strengthen the fixation of the structure, many garage owners enjoy documenses. They can be placed on top and bottom from the inside of the gate. Their manufacture is not too complex.

2 holes are made in advance in the floor and ceiling. Their diameter is 2-2.5 cm. To strengthen the changes, the finished frame should be fixed by the loop guides. Application of grazing should increase safety of the gate design. Doing the goal on the gate for the garage with your own hands in the event that the design provides a wicket. The entrance to the garage is carried out through the gate. For this deposit opens from the inside, and the gate swap completely. Castle can be chosen attached or mortise.

Painting and insulation of swing garage gates

After making a garage gate, with their own hands it will be necessary to paint the finished design. This is carried out until the final installation. Collect the sash should not only from aesthetic considerations, but also in order to protect elements from metal from corrosion.

Color homemade garage doors can be an atmospheric-resistant anti-corrosion paint for metal. The composition is applied manually with a brush or roller. For this, aerosols will be suitable, facilitating the entire process of painting. Before the coloring surface must be primed.

The paint is applied in 2-3 layers. The coating changes every 2 years.

Strengthening painted swing garage gates is carried out after full drying of paint. Fix all parts of the frame is necessary with metal pins, the length of which is 15 cm. Plugging the prepared elements in the slopes, it will take to stick the ends so that you can easily open and close the sash.

After strengthening the pins in the slopes, it is necessary to cut and stick the ends of the elements, as they may find it difficult to closure and opening the sash. To fasten together 2 parts of the framework, using steel plates with a thickness of 4 mm. It should be welded with a 50 cm increments, then the finished gates for the garage should be mounted on a loop.

To make a garage door with their own hands correctly, you should take care of the insulation of the whole design. Otherwise, about 50% of heat will leave it. From the inside of the sash, it will be necessary to strengthen the doom of wood and sawn timber. Materials with low cost are used as thermal insulation. It may be stone wool or foam. The shap is closed with clapboard.

The heat veil can be made of tarpaulin either from transparent plastic.

Types of lifting garage gates

The lifting gates are quite popular among garages owners, but many people think that they cannot be built on their own. To lift the structure of the design, hinges are used, lifting and lowering the sash moving from the vertical position to the horizontal. The lifting gate to the garage should occupy less space than swinging flaps. Two types of gate lifting designs are distinguished:

• lifting-section;
• lifting-swivels.

A lifting structure consisting of 50 cm wide sections is usually made of wood, metal or plastic. The inner emptiness between frame frames should be filled with insulation of polyurethane foam. Sections will need to connect with hinges having plastic or steel moving parts. If the type of material is selected correctly, the whole design will be durable and high-quality. If you make a lifting gate with your own hands, you can save your budget. This design is considered very convenient and easy to manage. At the same time, it has a fairly low protection against hacking.

Rotary gates for the garage, as well as sectional, rise and fall due to the presence of hinges.

The construction must have only one sash. In contrast to the previous type, such a canvas protects the garage from hacking with ill-wishers.

The obvious advantage of the lifting-turntable consists in the integrity of the canvas. For its trim, you can use the sandwich panels or metal. The cost of a solid wooden canvase is high because it has a lot of weight. A foam and chained plate can be used as thermal insulation material.

Technology for creating lifting garage gates

Before making the garage gate of the lifting type, you should select the shutting mechanism. After the design of the sketch, you will need to prepare all the necessary materials with tools:

• plywood shields;
• steel pins (trimming reinforcement rods 15-18 cm long);
• spring D \u003d 30 mm;
• sheet steel;
• wooden ram 120x80 (racks) and 100x100 (cross);
• bracket chaserler 8x4,3x0.5;
• steel rod d \u003d 8 mm.

Installation of the garage gate is performed in the following sequence:

• knock out from 2 supports and cross the frame to connect the parts using the corners or plate;
• the lower part should be opened into a 2-cm concrete tie;
• strengthen the box in the opening of steel pins;
• collect the frame of the canvas and to see plywood, attach the outside of the iron;
• make a backup from the corner for the design;
• make a drill 3 holes for fastening the spring bracket.

To connect the spring with the bracket, it is necessary to prepare the adjustment plate using the steel strip. Next, the spring is connected to the bracket. The extreme coils of the spring must be used with the help of pliers to make the hooks to which the steel rod is mounted below. From the corner you need to make a hinge angle to weld it to the frame. So you can install the lifting lever on the hinge at 12 cm. Next to the lever end, the tension regulator plate should be strengthened.

For the construction of guide rail, you can use a pair of corners.

They need to be welded around the edge, following the internal distance, which should be between the vertices along the entire length of strictly 5 cm. Then rail is attached to the plate. The lower end of the crossbar must be from the axis at a distance of 8 cm.

On the other end of the coast at 12-15 cm from Niza, it is necessary to strengthen the channel. It is attached to the ceiling brusade by means of a bolted connection. Before correctly consolidated, it is necessary to check the horizontal guides.