How to collect a shower cabin Nautilus. Installing the shower cabin with your own hands - assembly instructions

Many refer to specialists to establish a shower. But most of the owners of apartments can cope with it on their own, using the necessary tools, as well as studied all the methods of such installation.

Today, the market presents a huge variety of shower cabins of different shapes and sizes.Some of them are sold already in the assembled form and simply need to be installed correctly. But they are not popular. It is determined by the fact that they are not always comfortable due to their size, which does not pass in the doorway. Shower cabins requiring assembly are the most in demand. Many specialists advise paying attention mainly to these models.

Types of cabins and equipment

It should be immediately noted that all kinds of shower cabins differ in shape, manufacturing materials and a method of installation relative to the bathroom space. We will analyze every kind of Read more:

Closed models

Are the most common option. Each second person who prefers shower cabins can be found exactly this kind. It is characterized by closed walls and is a separate small room. The closed shower cabin also has a door, pallet, roof and watering can. Included additional features that are needed for a comfortable taking of the soul. Optionally, the water heater and even the radio can be installed. The main minus of this kind of shower cabin is the cost, which is higher than the average on the market.

Much depends on the manufacturer, as well as the material from which the cabin is made. One of the main advantages of such models is good sound insulation. Advantages also include additional functions, a variety of models on the market and fast installation.

Open cabins

In a similar case, the wall will be the wall of the room itself. Equipment of this type of shower includes only the door, a pallet, to which a person becomes, and a wande for the shower. The option is quite simple and has no additional features. Mostly such models are installed in the corner of the bathroom. Of course, the main advantage is the cost. Such a cabin is the most budget among all represented in the market. The ability to build a cabin of any area, which will be necessary for comfortable use.

The main drawback is the difficulty repair of sewer and water supply units.Open models do not have the top base, that is, the roof. Thus, the "tropical shower" is impossible in this case. An ordinary shower can be used that is connected to the mixer. This type of shower is designed only to be easy to wash, but do not relax under warm water.

Pallets are needed to collect water, as well as its drain into the sewer. The pallet form is divided into angular and rectangular.

When it is selected, first of all, pay attention to the depth, which is divided into:

• Deep, or high pallets. Very similar to a small bath, which provides the opportunity to sit and dial water.
• Medium sized pallets. They are considered the most versatile and are used much more often than other species.
• Low pallets. They are pretty compact. Often they are called flat. It is due to the fact that they are practically invisible. Such pallets require special water drain techniques. Otherwise, problems may arise and water will not go into the sewer.

Most often there are pallets that are made of acrylic.

You can also find products from other materials:

• cast-iron;
• steel;
• faiences;
• from artificial marble;
• natural stone.

As a rule, the most popular and frequently used is the acrylic pallet. It is distinguished by durability, ease of care and inexpensive cost. The most expensive is a pallet made from natural stone. The main advantage of its advantage is rapid heating. As a rule, the pallet retains heat for a long time, which makes stay in the shower more comfortable.

Walls are the necessary components of the shower. Their main function is to protect against water, which can go far beyond the booth. The raw material for the production of doors is plastic, glass or aluminum. Glass doors are the most sought-after. In the market, they are presented in two versions: matted and tinted glass.

The standard setting of the shower cabin is the following items:

• pallet;
• rear panel;
• roof;
• racks.

Dimensions

The market presents a large number of shower cabins of different sizes. When choosing, it is important to determine first with the size, and then look at the design and complete set. Thanks to the small dimensions of apartments, many people prefer to set the shower cabins, and not bath. It significantly saves the place, and is also the most convenient way of taking the soul.

In the event that none of the presented models presented will be approached by the Buyer, it is always possible to manufacture a shower cabin to order non-standard shape and magnitude.

Width

The smallest width parameter is considered to be 0.75 m. It is possible only in asymmetric models. Well suited in a small bathroom. Such a small size significantly saves the place in the bathroom, which makes it possible to install it even in the smallest room. The only minus is the inability to completely relax.

In such a shower cabin, you can only be in the standing position.It's not even a speech about to sit or lie. Additional features, as a rule, are not included in the package. But it should be immediately noted that such a size is suitable only to small people. For example, high and massive men will feel uncomfortable in it. Therefore, before buying, you need to go inside and evaluate the situation. Such an action will help not make a mistake with the choice.

The minimum size of the width of standard models is 0.8 m. They are very popular among users. It is determined by the fact that the largest number of rooms allocated under the bathroom are small. This option will quite well save the place and allow you to install additional techniques or furniture in the bathroom. The cost of such a shower cabin is low and it can afford an average person. Functions that can be in the booth will create an ideal atmosphere for taking the soul.

The maximum width of shower cabins can reach 1.8 m.It is the most convenient option that makes it possible to accommodate in two people at once. This model is usually used in large rooms connected to the toilet. Due to the large sizes, the shower cabin may include a number of additional features, such as hydromassage, aromatherapy, radio reception, telephone and other. The cost of such a design is significantly higher than the previous one. But it justifies the invested funds.

Models of shower cabins are also available, which are made with the bathroom. They are also called combined. On the perimeter of the bath there are walls, and the top can be both open and closed. Unlike familiar to all shower cabins, such a structure is quite large, so it is only suitable for room room. The user is given the opportunity not only standing to take a shower, but also relax in a horizontal position. This design has its advantages and disadvantages.

Pros:

• You can take both shower and bath. Perfectly suitable to lovers to warm up in hot water.
• Spacious shower. Conducted this is a rather size of the bath.
• Made most reliably. High sides provide security, as well as control the water level in the pallet.

Minuses:

• When leaving such a shower cabin, it is necessary to overtake through a large pallet, which is not convenient for all people.
• Cost. The price of such an option is high enough compared to the usual shower cabin even the largest size.
• The design is high enough and can reach 2.5 m.

It is worth understanding that the wider cabin of the shower, the more convenient to use it. Places inside should be enough to move while taking the soul.

The height of the shower cabin is also an important factor when choosing. The smallest height is considered to be 1.98 m. It is comfortable, but not suitable for everyone. The highest CABIN is 2.3 m. Comfortable curtain height is 2 meters.

It is worth noting that the height is selected individually. At the same time, it is necessary to take into account the growth of each family member when buying. It is desirable that the "stock" remains. Therefore, it is recommended to take the largest shower cabin immediately. As a rule, the ceilings in the bathroom will allow you to install such a design.

If the size of the shower cabin is chosen correctly, then its installation will not be problematic for the user. The main thing is to navigate the market for the presented models. Side models of shower cabins remain the most popular and sought-after. It is determined by the fact that their walls are tightly adjacent to the walls of the bathroom, which is the most comfortable and safe option. Installing such a cabin is also quite simple.

The widely represented option is precisely the square shape of the shower. But it does not use much popular, although the installation of this model is not difficult.

Preparation and tools

Preparation of all necessary tools that will be involved in the work is the most first step in the installation. Thus, the installation of the shower will not seem complex and problem occupation.

You will need the following:

• screwdrivers of different types;
• gas key;
• plumbing hoses;
• sealant;
• siphon;
• drill;
• foam assembly.

Before starting the installation, make sure that the floor is flat. In case of problems, it is necessary to align the surface, for example, putting the tile.

Stages of work

As a rule, the assembly of the shower always begins with the mounting work of the pallet. Connecting box with your own hands can occur both on the frame, and without it.

Each method has some nuances that need to be considered.

Assembling pallet

The pallet is installed on the frame, which is made of metal. The most important thing is a reliable fixation of the design. The frame is represented in the form of a frame design made of metal beams that are fixed crosswise.

All actions must be executed sequentially:

• In specially designated holes in the pallet, the studs are screwed to the stop.
• Two nuts screw on the studs. One is attached from below, and the other serves as a support.
• Frame support is installed on previous studs and nuts.
• The central leg is screwed and attached using the washer.
• Next, the fastening beams are fixed.
• The brackets that execute the screen for the screen are substituted.
• Placed pallet.

The correct organization of the drain during the installation of the pallet is the main task. Siphon should be put if it has not been placed. The main thing is to check the tightness at the junction of the pallet and siphon. In case the leakage is detected, it can be easily eliminated by the sealant.

If the pallet is small, the frame is not required for it.In this case, it is necessary to correctly install the siphon. The hose is disconnected from the clamp. The siphon joins the pallet, pre-passing sealing at the place of the joint to avoid leakage. It should be waited when the sealant will dry completely. After that, the hose and the clamp are returned to the place.

After everything is fixed, it is necessary to check the design for tightness. For this, water is poured and checked whether there is a leakage. This is a fairly important point and it is better to do it at the very beginning when it is possible to fix everything in case of problems. Then the design should be raised by approximately 5 cm and pour the mounting foam.

The pallet must be loaded. Moreover, weight should be large enough. For this, building bags filled with cement are suitable. It is desirable to decompose the entire cargo evenly.

Communications

An important part of the installation of the shower cabin is to summing it up to sewage.

To do this, you need to perform a number of works:

• A protective film is located around the drain hole that you want to delete.
• Rubber gasket, which is located on top, is best replaced by silicone sealant.
• Next siphon is screwed.
• The lower connection and thread are processed for reliable sealant.
• Next, the siphon is connected to sewage. It is worth noting that the connection must be treated with sealant for reliability.

It is important to choose the correct location of the shower in the bathroom and take into account that it is also planned to install, besides the booth. The power grid that goes to the water supply and water heater should be isolated. Waterproofing in a small-sized apartment should be extremely reliable.

Walls, doors and roof

This stage is the easiest to install the shower. But it is still better to ask for another person to help you. So the installation process will be even easier. During installation, it is desirable to follow the recommendations of the manufacturer, since all showers have some differences from each other. Fixing the walls is performed using special bolts.

Stages of work:

• From the top of the pallet, the protective film is removed, but the bottom remains protected.
• A wall is installed after the pallet moves away from the wall.
• Holes in the pallet should be connected to the corner and fix with the help of screws. It is desirable not to apply special efforts to this. Moves in this case should be soft.
• It should be marked with a marker of corners that have special holes.
• Next should be removed the partition and apply a small layer of silicone.
• The partition is returned to the place and unnecessary parts of the silicone are removed.

• The pallet with the partition is located to the wall and is trying on the central part.
• Silicone should be applied on the shake of the side wall and the central panel.
• The wall and the central panel are binding.
• Similarly, the next wall is attached.
• The profile is fried by silicone and the process of installing the partition.
• The installation of the lower and top profile is carried out. Silicone should be applied to the bottom.

Roof assembly:

• By revealing the ventilation grilles, the protective film is removed.
• Sealant should be treated with watering can. This is done so that it fits tightly to the place of attachment.
• The ceiling is installed so far without using silicone. Twisted from the bottom with the help of four screws.

• Hoses are connected to the slats using the clips.
• Wires must be connected based on colors and labels.
• Next, you should connect the cab and check water and electricity.
• The lower perimeter and the central stand is treated with silicone.

Assembling the shower cabin with your own hands step by step, photo and video instruction

Every day, more and more people are solved on the purchase of a shower cabin for their bathroom. And it's not easy, because in our modern and fast rhythm of life, sometimes there is no time for the adoption of the bath. It turns out that it is worthwhile the bath itself and takes A place in the bathroom. You can simply put a shower cabin and also post a bunch of necessary things, such as a washing machine or beautiful bathroom furniture.

But if everything is simple with the bathroom, listed and set, and you can take water procedures, then with the shower cabin, the process of assembly and installation is a bit more complicated and longer. The many people scares it and after purchase they turn to professionals that gather shower cabins.

• Video Instructions for assembly and installation of a shower cabin, on the example of the shower cabin Erlit

On the one hand, it is correct, but if you have hands and head, then why pay extra money. The price for the work of assembling the shower cabin can be very large, it all depends on the size of your bathroom, and the size of your shower cabin . For example, if you have a big bathroom and a small shower cabin, then the installers will easily, simply and quickly collect the product, and they will not take much money with you, but still it will be at least three thousand rubles for assembly and installation.

Therefore, in this instruction, we will look at how to collect a shower cabin with your own hands, without resorting to the help of installers. Immediately turn your attention that almost all cabins, especially Chinese production, are going to the same. For example, assembly of the shower cabin size 90 by 90 centimeters, there is little different from the assembly of the shower cab 80 to 80 centimeters, or 120 per 80 centimeters. Also on producers, For example, the assembly of the niagara shower cabin, is not much different from the assembly of the Erlit shower cabin, or the assembly of the shower cabin. Water world. There are of course exceptions and nuances, but the principle and algorithm for assembly and installation will be similar to 80-90 percent.

• Video instruction assembly rectangular cabin

Very often you can see a shower cabin in the exhibition hall in some store, and many may have the impression that it is poor quality threatening, staggering. But it is not so, because very often, the exhibition samples are collected poorly, and its purpose is to show a shower cabin in the assembled form visually. In fact, 80 percent of its performance characteristics depends on the assembly of the shower cabin, as well as you collect it, so long it will stand with you.

So, you bought a shower cabin. Assembling the shower cabin is made in a pure, renovated room. Tile like outdoor so and wall should be posted by the way you can not lay out the shower cabin for the shower, and on this save.

Hot and cold water wiring , as well as sewage must be performed, below in the pictures you can see the scheme of connecting shower cabins in size 90 * 90 centimeters

and 120 * 80 centimeters

Also, if there is a radio, backlight or exhaust in the shower cabin, it is necessary to bring a rosette with grounding.

If you collect a shower cabin in winter, it should take room temperature. Therefore, after it was brought to the apartment box, open them and wait a couple of hours.

Required tools for assembling shower cabin:

1. Screwdriver or drill
2. Silicone sealant
3. Set of crusades and bits of screwdriver nozzles
4. Spanner 14,17,19 or adjustable key
5. Drill
6. Level
7. Roulette
8. Pencil

The assembly of any shower can be divided into several stages.

1. Pallet assembly (if it is disassembled *,)
2. Pallet control adjustment
3. Assembly of the central panel (if it is not assembled *)
4. Installing the rear walls and the central panel (if it is dismantled)
5. Assembly and installation of front glasses and doors
6. Installation of attachments and decorative equipment.
7. Roof setting
8. Connect to sewage

* Some manufacturers supply shower pallets already in the assembled form, the central panel, and the rear wall.

Before assembling bed on the floor, cardboard, it will help not scratch the pallet, as well as lock the glass of the shower cabin. By the way, be careful with the glasses, do not put them on the tile, only on the cardboard. You can collect a shower cabin and one person, but much more convenient to invite assistants, so the assembly will go faster and more convenient.

STAGE 1. Assembling a shower cabin pallet.

This stage can be skipped if you have the already collected pallet, some manufacturers supply them in the already assembled form. If so, then immediately go to the second stage

1. Locate Cardboard from pallet packaging on the floor in the bathroom
2. Remove the shower pallet and put it upside down
3. Remove the metal frame, screw the racks and legs on it. Encode it on the shower tray. Screw it with self-draws included in the kit. Firmly tighten the nuts using keys.

Attention, do not confuse the length of the screws, so as not to pierce the pallet. Also, make you screwed the racks and the pallet frame to the mortgages that are located on the pallet.

4. Correct the angle of fastening the front panel around the perimeter of the pallet. Install the front panel.

5. Clean the drain to the pallet.

Pallet assembled.

Some for greater durability of the pallet before installing the frame cut out of the plywood, the workpiece along the radius of the pallet. When you screw the pallet, it turns out such a design: pallet -Forcase-frame. It will be very reliable and firmly. Either, for amplification, you can put bricks under the pallet, especially in those places where there is no frame. These measures, we recommend that you do to increase the reliability of the pallet.

2. ETAP.Regulation of the pallet in the level

1. Move the pallet on the legs and put it in the place where it will stand you.

2. With the help of the vertical level and unscrewing the legs, adjust the pallet so that it stands exactly.

You can also connect temporarily in the sewer and try to gain water into the pallet, and see how water will go. If necessary, adjust the water slope with the legs so that it can easily leave.

3.Tap. Called central panel

If you complete the collected shower panel, then go to the next step.

1. Discussion from the box Central Panel and Accessories (Mixer, Radio, Nozzle)

2. Clean the nozzles, and the mixer.

For even greater reliability, you can miss the places of contact with nozzles with silicone sealant.

3. Clean the mixer

4. Clean the control panel.

5. Advance the protective film from the panel.

4.Etap. Installing the rear walls and the central rack

You can skip this stage if you have a rear wall and a rack are collected in the kit. This work is better to perform together.

1.Davit the rear wall of the boxes (it does not matter plastic or glass)

Carefully look at the holes where the top and where the bottom, and also see what the wall is right, which left.

2. Install one wall per pallet , pre-missing the silicone sealant the place of contact of the wall and the pallet, tighten it with bolts, or self-drawing (depending on what you are included) sometimes there are no holes under the bolts on a shuffle pallet, then you have to drill them, after having puts the rear walls and the central panel pallet.

3. Accurately holding the rear wall. Put the central rack on the pallet.. Also lubricate the places of contact with the pallet and with a sealant wall, and screw them with each other. (Bottles or screws depends on the configuration)

4. At the analogy Gently put the second rear wall on the pallet , Lubricate the sealant of the place of contact of the pallet and the central panel and secure them with bolts or self-draws. On this, the back wall can already stand itself, you can not support it, but still be careful, as it is not very reliable.

5.Thetap Assembly and installation of front windows and doors

This work is also better to perform together with an assistant

1. Accurately get the doors and glass out of the boxes and put them vertically. Clear cardboard to not break the glasses, Calen glass has very fragile corners.. Also get the vertical, horizontal profile, and rubber seals. Caution Immediately determine which horizontal profile top and how lower, they are sometimes different in width. The top profile will be widely wide.

2. Delivers on the side windows rubber seals, lubricate them with a sealant and insert into the vertical profile. ATTENTION, it is necessary to insert evenly and neatly, if something does not enter no need to beat the hammer or pull on the glass of the glass. Sust and try again. Exactly comes very tight.

3. With the help of long screws and screwdriver, connect and tighten the vertical and horizontal profile. Gently hold the horizontal profile, and get into the holes of the vertical profile with a screw. Initially, you can fasten the horizontal profile to one vertical half with glass, then to the other.

4. Correct the corners of the side of the side windows to the horizontal profile.

5. Add the first wall to the pallet together, pre-lubricating the place of contact of the profile and pallet with silicone sealant.

6. Create the front and rear wall between themselves with self-drawing, you can also place the walls of the walls to lubricate with silicone.

7. Enclose on the door of the rollers, usually they are included in the kit 8 pieces, 4 upper and 4 lower, do not confuse.

8. Install the doors to the guides on horizontal profiles

9. Clean the bumps of doors that come complete with rollers, on the horizontal profile

10. Install sealing gum and adjust the doors

6.Taptation Installation of attached and decorative equipment

3. Install and screw the decorative covers that hide the fan and speaker

4. Install the roof, and screw it with bolts to the rear wall. The places of contact of the roof and the back wall should not miss silicone.

8.Tap connection to sewage

1. Offen all hoses that are located behind the shower cabin, namely the hoses from the mixer to the top shower, manual shower. In the presence of hydromassage and foot massages also connect these hoses to the mixer.

On this assembly of your shower cabin, you can be considered complete. How do you see, assembling the corner shower with your own hands is not such a difficult case, as it may seem. I hope our shower assembly of the shower will help you with this.

In this manual, we reviewed the assembly of angular shower cabins with a deep pallet, shower cabins with a low pallet, as well as rectangular shower cabins are going about as well. .

We also recall that the stages of the assembly of the shower can be changed a bit, there is nothing terrible in it. And also, almost all shower cabins, almost all Chinese manufacturers are assembled almost equally, with rare exceptions.

Original instructions and schemes for assembling shower cabins, different, specific manufacturers and specific models, you can find on our website in the relevant section instructions.

Literally ten-fifteen years ago, the shower cabin was the subject of luxury. But now more and more people get rid of old overall baths and install shower instead.

This allows you to increase the free space, which in urban apartments is usually lacking. The current range of such cabins is wide enough, but the proper selection of a particular model is not enough - it still needs to be installed and connect to communications. You will learn about this and many other things after reading this article.

Note! Mounting work is not so complicated as it may seem. But in order to avoid possible problems, it is necessary to first decide on the main types of cabins.

Shower cabin is a closed box for hygiene procedures. There is a lot of models, but they can be divided into two large groups.

1. Open

Open cabin space is limited only by the walls of the box and the bathroom. Similar structures are also called shower corners.

There are similar models expensive, but the installation is carried out quickly and without any problems (taking into account the fact that the alignment and waterproofing of the floor and walls will be required).

Note! In most cases, shower corners put in small apartments, where the installation of a full-size soul is impossible due to the deficit of free space. But if the bathroom area is too small, then the corner should be selected with a transparent door opening through.

2. Closed

In closed cabins, in addition to the walls there are also the bottom and "ceiling". Simply put, they are closed comprehensively. Such cabins can be of various sizes, but usually it is from 0.7x0.7 m to 2x2.1 m. They are also divided into simple and multifunctional, and in the latter I have a number of additional options:

• aromatherapy;
• hydromassage;
• "Summer shower;
• color treatment;
• "sauna";
• radio.

With the installation and connection of the shower, it is easy to cope with the installation, you only need to follow the manufacturer's instructions and make a maximum effort to work.

Stage 1. Selecting a place to install

The place for mounting a shower corner must comply with the two requirements:

Stage 2. Assembly

The installation begins with the assembly of the design, which will help to deal with all the nuances of the connection and determine the real dimensions.

Note! Regarding the assembly technology, we will not advise anything here, since it all depends on the design features of a particular model. As mentioned earlier, only the manufacturer's instruction can help.

Stage 3. Connecting to the sewage system

Connection should be started from the pallet mounting. Below are the recommendations for this procedure.

1. The pallet should be installed strictly horizontally, so it is better to use a long construction level.
2. Complete with the cabin always go special supports, with which the horizontal pallet is adjusted. If you wish, you can consolidate an additional support in the center.
3. The pallet should be perpendicular to the wall.
4. The floor should be perfectly smooth (used the same level). If this is not achieved, the pallet will not tightly stick to the walls and, as a result, the leakage will arise.

After assembling the pallet, the connection itself begins. Here is a sequence of actions.

Step 1. All the elements of the apron are removed.

Step 2. Rises part of the pallet.

Step 3. On the drain knee located at the bottom of the pallet, the corrugated hose is put on (a special side nipple is provided for attachment). This hose will connect the cabin with sewage.

Step 4. The second end of the hose is fixed on the plum located in the floor.

Step 5. The pallet is placed in place.

Note! The extremely high-quality installation can be achieved only if the floor indoors perfectly, and the walls are located at an angle of 90ᵒ.

Before the start of the assembly, the design is carried out "verification" drain. It is much easier to correct all errors until the installation of a shower corner is completed.

Stage 4. Water supply

The competent connection of the cabin to the water supply system plays an equally important role. To do this, use exceptionally high-quality pipes and connecting fittings. Moreover, all connections should be carefully sealing.

Requirements for connecting

1. The pipeline is paired along the plinth either hiding at all.
2. Water to the soul is derived from under the sink.
3. The pipeline crashes at least one water filter.

Step-by-step instruction

Step 1. Initially, the water supply is overlap, then hot / cold water cranes open in the bathroom - so the pressure in the system will decrease to the required level.

Step 2. The old shower is removed - for this pliers weakened and all fasteners are dismantled.

Step 3. With the same pliers, the old coupling is twisted. Each segment of the pipeline is equipped with compression fittings.

Step 4. Fittings are covered with lubricant (preferably with machine oil). Cabin adapters are screwed and tightened by pliers.

Step 5. In accordance with the instructions, anchors are attached, if necessary, the holes are made somewhat larger. Then screw the screws.

Note! It is desirable to separate the place of attachment by a painting ribbon, otherwise there is a chance to damage the tile when working.

Step 6. Hoses are connected to transient fittings, connections are clamped.

Step 7. A shower panel is cling to anchors. Fastening begins on top. Water pipes are fastened to the outer part of the panel, decorative plates are installed.

Step 8. The operation of the system is checked. The flow of water is resumed onto the riser, all connections are checked for tightness. Only after that the handle is attached.

It remains only to fix the walls. This must be done in accordance with the manufacturer's instructions, while the silicone sealant and sealing gaskets should be used.

Final "Strokes"

At the end of the assembly, you need to hold a number of events related to the final arrangement of the shower.

1. Electricity

Only those models in which there is a hydromassage function or there is a steam generator are connected to the power supply. It uses an isolated three-cenched wire with a cross section of 3 cm².

2. Ceiling panel

Typically, the ceiling is included with the cabin. In this case, the ceiling is connected to the hose with watering can and other components - speaker, lamps, and everything provided by the manufacturer. The joints formed between the speaker and the panel are processed by a sealant in order to avoid "buzz."

The ceiling is installed on the appropriate fastening elements located in the upper part of the structure. The joints in this case are also processed by sealant.

3. Accessories

Step 1. Rollers are installed in the upper and lower parts of the door opening. The rollers located on top are maximally turned to the installation.

Step 2. The door is separated around the perimeter by sealing material and put in place.

Step 3. To determine the optimal position, the upper rollers are adjusted.

Step 4. Screws, with which rollers are fixed, closed with decorative plugs.

Step 5. The remaining fittings are installed - the mirror, handles, etc.

Upon completion of the installation, final testing is performed. As mentioned above, all connections are made with hermetic, and the pallet should not creak during operation (otherwise the position of the legs under it is once again adjusted).

Operation and cleaning of the shower

For all models, regardless of the type of operation rules are the same. There are only means for washing - the choice of one or another depends on the material from which a specific element of the design is made.

When operating, you need to remember some of the requirements.

It is also worth noting that the cleaning of the cabin at frequency is divided into several types.

Video - Sink Shower Cabin

conclusions

Install the shower room is simple enough, this requires only minimal plumbing skills and necessary instructions. In the absence of the first or second, it is better to entrust the installation by a specialist.

Video - Instructions for installing shower

The cost of the services of a specialist installation of a shower cabin is about a quarter of the cost of the equipment itself. An independent installation according to the instructions will help you to save significantly. However, if the cabins from famous European manufacturers are accompanied by detailed manuals, then when installing a Russian or Chinese model, difficulties may arise.

Installing an angular type cab

Corner cabins for the shower are widespread: they are installed in most apartments with disabilities of bathrooms. Let's determine how to assemble a shower cabin with your own hands in the corner version of its location.

Instruments

For work, the following tools will be required:

• cross and spline screwdrivers;
• building level;
• spanners;
• silicone pistol;
• screwdriver;
• transparent silicone sealant;
• elastic hoses;
• synthetic FUM-seal (for pipes from metal, you can use the pass).

Work is convenient to produce in gloves, since the surface of the cabin elements may have unpleasant roughness. Additionally, in addition to factory, you may need self-tapping screws, nuts and washers.

Cabin elements

As part of the shower kit there are elements such as:

• vertical racks;
• pallet;
• rear panel;
• walls and doors;
• guides for sliding doors;
• dome (in closed-type models);
• enclosing screen;
• factory fasteners.

Ensure their integrity and absence of external defects. The assembly is recommended to be carried out together in order to avoid inaccuracies when dusting the cabin elements.

Mounting pallet

The scheme we proposed in detail describes how to assemble the pallet itself. At the stage of preparation for installation, it is necessary to thoroughly align the walls and the floor on the installation site, since the stability of the cabin directly depends on this moment. Frame, fixed on an uneven wall, will have to attract self-drawing. Such actions may lead to the appearance of deformations.

Before starting the installation, the pallet must be released from the protective film and turn over so that the bottom is from above. To the location of the drain with the help of elastic hoses supply a water removal system. The best option will be the location of the exit to the sewer pipe right under the drain hole of the pallet.

Important. Perhaps it will have to install a tee in advance for a drain - in case the flow of the bath, shells, washing machine and other equipment is assumed.

Installing frame and screen

Supports on which the vertical racks are attached are crucible on top of the bottom and combine with stiletto pallet housing. On the studs screw the nuts, then the washers. The protective screen is attached to the brackets with screws.

Sometimes supports can be represented by the support frame already assembled at the factory - in this case, its holes must entirely coincide with the holes in the pallet.

Important. On the correct location of the supports the protrusion on one of them: Make sure it is outside - otherwise the pallet will be installed with distortion.

Setting legs

The pallet is mounted on special legs that fix nuts. The legs become a peculiar continuation of the studs fixed in the pallet. The central leg is attached to a shorter support. Supports are exposed and finally fixed with locknuts.

In cases where the pallet does not imply installation on the legs, it is necessary to thoroughly align the surface of the floor, taking into account the requirements of the instruction on the angle of inclination towards the drain.

Installation of siphon

Next, begin to set the bottom valve in the drain hole, as well as the siphon. In order to avoid leaks, the joints of the joints are treated with silicone. To make sure that there are no leaks, at the end of work, fill the pallet with water for several hours, breaking the hole of the drain hose. With successful passage of such a test, you can connect the siphon to the drain system. When all operations are completed, the pallet is turned over and installed in the angle.

Assembling corps

Elements of the shower cabin in many cases are installed on an aluminum frame - it is durable, it is easy and protected by corrosion. Vertical frame racks are fixed on guides. In open models of shower cabins, the frame is attached to the wall by the transient profile.

Installation of walls and doors

In order to turn the wall correctly, it should be borne in mind that in the upper areas there are always more holes. Guides for sliding doors complete Two: Wide is installed on top, and narrow - bottom. Guides have grooves in which the cab walls are inserted.

Sliding doors are installed on rollers with seals, their position is adjusted using the top rollers. The joint area is treated with silicone.

Council. When applying silicone to the joint area with the walls and the rear panel, do not "hide" transverse channels in the surface of the pallet designed for water drain.

Installing the back panel

The rear panel is also attached to the base of the pallet with self-draws or bolts. If the cabin is equipped with electrical devices, after installing the rear panel and connecting to the network, you can check their operation.

At the end, you can proceed to the installation of the dome, in which there are:

• shower canoe;
• fan;
• illumination;
• speaker.

To prevent the fan vibrations, as well as the rest of the equipment, when they are installed, the edge is recommended to be treated with silicone.

Final adjustment

When the cab is fully assembled, you can fix the shelter, handles, holders on its walls. After final adjustment and checks, the nuts and fasteners are tightened, the water and plum is connected. If the pallet makes cracks while finding a person in the cabin, this indicates the need to additionally adjust the height of the legs.

Note. For a number of models of shower cabins with shallow pallets, the leg alignment is provided under the tilt towards the drain - this moment is necessarily prescribed in the instruction.

Features of Chinese models

The build scheme described by us is universal for most models of shower cabins. To determine how to collect a Chinese angular shower cabin, if it is a model with any features, let's talk about the cabins, "dropping" from the general list.

Shower cabins "Niagara"

The walls and doors of the shower cabins "Niagara" are mounted non-standard:

1. First, they establish the foundation by placing it close to the walls of the room;
2. Next perform the installation of the side walls, connecting them with the base through special holes;
3. The joints of the joints are treated with silicone and wait for its solidification;
4. In the side walls there are loops in which the doors are installed.

The main requirement to install the Cabin data is good sealing of silicone. It is due to the features of the profile that is loosely adjacent to the cabin elements. Also, a number of models require the accounting of water pressure: it must be high and stable for normal operation. Information about pressure in the system must be specified in your home organization serving.

Shower cabins ika

Shower cabins "IKA" are mainly represented by rectangular models with hydromassage function. When installing this equipment, high attention should be paid to adjusting the position of the doors: the slightest inaccuracies can lead to flows.

Shower cabins "Erlit"

The cabins of this brand have good performance, but are supplied with the most common instructions that do not contain detailed descriptions and recommendations. For Cabin "Erlit" is characterized by the same need for careful sealing of all sections of the compounds. Special attention should be paid to the quality of the manufacturer of the factory siphon. In many cases, consumers come to the conclusion about the need to replace it.

Differences in the collection of open and closed cabins

We offer step-by-step instructions, how to properly assemble a shower cabin, fully applicable to the models of both types: open and closed. The difference is that the walls of the cabin with the dome are installed on the pallet in the already assembled form. The installation sequence is as follows:

• initially, the back panel is close to the wall;
• next, the rear panel equipment is connected to communications;
• at the final stage, the front part is installed with the doors.

In all cases, individual features are possible, for the accounting of which you need to get acquainted with the instructions.

Installing rectangular cabins

Often, rectangular cabins are equipped with expensive hydromassage equipment. At the same time, the pallet can be used as a full-fledged bathroom. The main feature of the installation of the cabin of this type is to comply with the order of installation of the walls:

• the first is installed the rear panel, on which the equipment is located;
• it is connected to the side walls;
• in conclusion, install the facial part with the doors.

By installing the shower cabin independently, follow the installation rules and the requirements of the manufacturer's instructions. Also, you should not neglect the safety regulations.

Shower cabin is an excellent bathroom alternative, especially if you have to equip a small-sized bathroom. However, the owners of spacious bathrooms are increasingly choosing comfortable and multifunctional shower cabins.

The choice of the optimal model, competent installation and careful operation - the key to the long, comfortable and uninterrupted use of the shower.

Benefits of using the shower

Shower cabin is a specially equipped, fenced place for taking a shower. Today, the possibilities of using shower races increased, various additional functions appeared: hydro massage, steam generator, stereo and other.

Many consumers celebrate a number of the advantages of the shower in front of the bathroom:

Shower cabins: reviews

In order for all the advantages of the shower cabin to be fully implemented, it is necessary to choose the right model and correctly install it.

Types of shower Cabin: Features of structures and installation

All shower cabins can be divided into two main groups:

1. Shower corners - open cabins.
2. Shower boxes - closed cabins.

Shower corners

The angular shower cabin is one of the most popular models. The design of the cabin has no rear walls and roofs. The space around the shower cabin is limited from one or two sides by the walls of the cabin, and with others - the walls of the bathroom.

Open shower cabins can have a shower tray or installed directly on the floor of the bath.

To install a shower corner, you can purchase a ready-made cabin set (walls, doors and pallet) or select items separately

Depending on the depth of the pallet, open cabins can be divided into several types:

Low pallets do not have the ability to reinstall, as they are mounted overha. Installation of deep pallets on a metal framework allows you to maintain hidden communications, and if necessary, transfer the shower to another place

Shower cabins: Photo

Features of the design and installation of open shower cabins:

Shower corners from transparent glass visually expand space, giving elegance and ease of bathroom design

Shower boxes

Shower box - Fully closed space with entrance doors. A closed cabin has a roof and walls on all sides.

Such boxing is more convenient to use and easier to install. However, the cost of closed models is higher than on open showers (buy ordinary boxing without special functions, at a price of 30,000 rubles, and a shower corner is from 7,000 rubles).

The price of the shower cabin of the closed type directly depends on the number of built-in functions, box size and manufacturing material

Shower boxes can have such functions:

Even the most primitive models of closed cabins have a radio, top and side lighting, seating, shelves, dispenser for detergents and a mirror.

Criteria for selecting a high-quality shower

You must choose a shower room based on the needs of the family and the parameters of the bathroom.

Before buying a shower cabin, you need to test: Check the strength of the pallet (like the bottom of the cabin), watch the fastening of the frame with the pallet, try to rack boxing elements (high quality cabin should not be fused)

Independent installation of a shower cabin of a closed type

The installation circuit shower directly depends on the complexity of the design, and the assembly sequence for most models is the same.

Preparatory work

In order to have an idea of \u200b\u200bhow to collect a shower cabin, you need to familiarize yourself with the instructions that comes in the kit.

Before starting installation, you need to prepare such tools and materials:

• building level;
• silicone sealant;
• spanners;
• sharp knife;
• crosshead screwdriver;
• paint;
• brush;
• gloves;
• siphon for plum;
• flexible hoses;
• fuma ribbon or palable;
• chisel;
• a hammer;
• perforator;
• simple pencil;
• instructions for the shower.

The preparatory stage implies the implementation of a number of events:

Mounting pallet

The assembly of the shower must begin with the installation of the pallet:

Fastening panels and fences

Before starting the installation of panels, you need to decide on the location of the glasses. If there are no markings on the fences pointing to the top and bottom of the part, then you can focus on the number of mounting holes - usually above them more.

The procedure for installing panels and fences:

At this stage, you need to check the operation of electrical devices (illumination, ventilation).

Installation of roofs and doors

Before fixing the roof, you must install backlight, watering can and speakers on it.

The distance between the ceiling and the roof of the cockpit should be at least 25-30 cm

You can use the available holes for mounting the roof, and if necessary, make new ones. The roof is fixed by bolts and screws.

Doors of the shower cabin are installed after mounting the side, rear walls and roofs

Door installation sequence:

Now you can scout accessories (shelves, mirror, dispenser) and accessories (handles, handrail).

Cab connection to communications

To the cabin it is necessary to bring cold and hot water. It is desirable that the operating pressure of the cabin (1.5-4 bar) coincided with the pressure of the plumbing line.

To connect the shower cabin to the electrical outlet, you need to install a separate moisture diskette. The outlet must be positioned so that the wire tension has occurred (optimally - on the side or behind the cab).

For a socket in the bathroom, it is desirable to install the RCD and select a separate line of wiring.

Assembling shower cabins (instructions): video

Installing a shower corner without pallet

Installing a shower corner with a pallet is practically no different from the installation of a shower box. Differences occur if the shower cabin is mounted without pallet - on the floor of the bathroom.

Before installing the cabin, it is necessary to prepare the base as follows:

1. Determine the size of the corner and choose a place for it.
2. Perform waterproofing of the floor and adjacent walls.
3. Install on the floor drain gear - the grille through which the water is merged into the sewer system.
4. Facing tile on the floor of the shower cabin should have a very low degree of slip.

For high-quality water removal, the slope of the floor in the zone of the ladder should be at least 3 °

Prevention of faults and repair of the shower

The shower cabin is important to maintain clean and control the work of all its elements.

In order to prevent the breakdown of the most important details (mixer, nozzles, steam generator), you should take care of the quality of water and install the filters of mechanical water purification. Such measures will significantly reduce the risk of calcium formations on the working elements.

Once every three months, the cartridges or cartridges in the filters must be changed

Over time, the shower cabin can start leaking. The main cause of a malfunction is a bad stood of seams or a spank of silicone sealant.

In this case, the cabin in places of leakage should be disassembled, clean the parts from contamination and the remnants of the old layer of sealant. After that - to apply a new layer of silicone sealant, collect the cab and well to lure the seams.

Assembly of the multifunction cabin of a complex design is better to entrust the professional, and you can carry out the installation of simple box or angle yourself, the main thing is not to rush and clearly follow the instructions.