Frame house one and a half. Frame house one and a half

A detailed report on the construction of a classic frame house, a size of 6x8 meters, with an attic.

The walls are standard for the skeleton, 150 mm, raftered on the roof of 200 mm, on the floors of the board also 150 mm.
Mineral wool will be used as insulation.
The roof is double with one "cuckoo", I plan to use rubberoid tile as a roof covering.

Let's start with the layouts:

In early September, the foundation was flooded.

The foundation is a ribbon, 40 cm wide with a jumper, height 1 meter, 50 cm above the ground, 50 underground. Reinforcement is standard, 12 reinforcement in the upper and lower part of three rods. Pulling wire.

Inside the foundations, a vegetable layer is chosen, geotextiles and loose clamzit is notched. Under the house with a size of 6x8 meters, about 5 mk bube took order. Keramzit.

The foundations are processed by the entire height of Bitumast with water insulation mastic. Then the site around the foundation was leveled for the convenience of construction by the tractor.

For the possibility of normal operation in the case of rain, a used banner was purchased and a canopy above the construction site was organized.

The larch board has been purchased for the first floor floor lining board. The foundation is tested for compliance with the level of the horizon and in the right places will be poured with cement (there were drops of about 20 mm, now everywhere in "0").

To cover from the inside, you wanted to order a plyland of 12 mm, but the seller persuaded to take OSB-3. Type modern material and all that. Brought the Baltic, Bolderaja. Photo Apply, know comments ...
They brought another 18mm on the floors, the manufacturer Egger, this better (photo №2), they decided to leave it, the Baltic firm seller without unnecessary conversations agreed to exchange to Faneru. So personally for me the question with the use of the OSB is closed once and for all.

The foundation is laying a substrate in two layers of Tehneelast EPP.
The frame of the first floor overlapping is assembled all on galvanized Samores 100x5 with a shot.

The lining board is attracted to the base of the foundation by anchor bolts. All places of compounds of wooden elements are laid by a plug-in material.

Bitumast was purchased a bucket of 21.5 kg. Almost all bucket took the foundation.

The instructions are written 100 grams per m2, but the real consumption is more. Well, probably looking at how to smear.
Profile corners apply as needed.

Under and between the lags and the lining board, the foam polyethylene was paved. All structures over lags will be laid by the material of vibrosek-M thickness of 4 mm and shumanet-100 with a thickness of 4 mm.

Between the lags of the first floor and OSB-3 of the draft floor will also be laid vibrosek-m 4 mm.

Late in the evening came the first car with 150 blackboard. The board unfortunately on geometry is not perfect, you have to shive ...

Between the floors of the first floor and the wall laying isoplat.

* - The specified value includes materials, delivery within 400 km from our production and construction of a frame house with Russian carpenters.

• The blockage is the natural humidity bar (spruce / pine AV) section 150 * 100 mm. According to the outer perimeter, the strapping is placed in two rows. The bar is processed by an antiseptic.
• Floor lags - a natural humidity board (spruce / pine AV) cross section 100x40 mm, with a pitch of 600 mm
• Black floor - natural humidity board (spruce / pine AV) cross section 19/22 * 100 / 150mm. Papohydrozolation - nanoseol with
• Floor insulation - min.vat KNAUF / URSA, a thickness of 50 mm. Parosolation - nanoseol "B".
• The finishing floor of the first floor is the dry tipped floor board (pine C) 36mm thick. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• The outer walls and frontones are a frame from Bro (Pine C) with a cross section of 40x75mm. Building on construction, black nails.
• Wall insulation of walls and frontons - Rockwill basalt plates, 50 mm thick. Parosolation - Nano Isola B.
• Internal wall covering - lining (pine c) 12.5 * 88mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• Partitions - frame from a bar with a cross section of 40x50mm. Plotting partitions - lining (pine c) 12.5 * 88 mm, on racks.
• The height of the ceiling of the first floor clean (from the floor to the ceiling) - 2,20m
• Ceiling liner - lining (pine c) 12.5 * 88 mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• Hearth overlap - min.vat KNAUF / URSA, 50 mm thick. Parosolation - Nano Isola B.
• Mansard Floors - Dry Plumbing Flooring Board (Pine C) Thickness 36mm. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• The walls of the walls and the ceiling of the attic - lining (pine in) 12.5 * 88mm. Fastened along the rafters through the membrane Nanosol V.
• The insulation of the monsard walls is Rockvul basalt plates, 50 mm thick. Parosolation - Nano Isola B.
• Mansard partitions (if any) - frame from a bar with a cross section of 40x50mm. Plotting partitions - lining (pine c) 12.5 * 88 mm, on racks.
• Rafters - farms from a natural humidity bar (spruce / pine AV) cross section 40 * 100/150 mm. The rafters are installed in 900 mm increments.
• Roofroom roof - natural humidity board (spruce / pine AV) 22/25 * 100/150mm. Controlling - Bar 20 * 40 mm.
• Coating - profile sheets of galvanized steel. Cruising vaporizolation - nanoseol C.
• Eaves and sinks of the roof of 200 mm wide - lined with clapboard (pine B) 17 * 90 mm.
• The staircase on the second floor (for homes with the attic) - on the assets of the planed timber, with steps from the geepboard.
• Doors - Wooden, Filöncated (Pine B). Size 2000x800mm. Pens, loops. Entrance door with hinged lock.
• Open terrace, porch (if provided for by the project). Supports - planed timber (spruce / pine AV) cross section 100 * 100 mm. Fencing - planed timber (spruce / pine AV) cross section 40 * 100 mm in two belts. Floor - Dry pinned floor board (pine c) 36mm thick. Must with self-drawing into each board. The boards are stacked with a step of 5 mm. Ceiling - lining (pine B) 17 * 90 mm.
• Sealing angles, joints, adjoins - plinth (pine B) 40 / 45mm.
• Finish finish of windows, doors - platband (pine c) on both sides.
• Delivery up to 400km from our base in Pestovo, Novgorod region + unloading of the house complex. (https://yandex.ru/maps/10920/pestovo/?ll\u003d35.809228%2C58.596895&mode\u003dSearch&oid\u003d1081678118&ol\u003dbiz&z\u003d17)

• The foundation is the refiner. 4 blocks of 200x200x400 in the end of the cement screed. The cabinets are installed on the rammed sandy pillow. Sand (or PGS) provides the customer.
• Waterproofing - rubberoid in one layer.
• Floor lags - a natural humidity board (spruce / pine AV) section of 150x40 mm, with a pitch of 600 mm, processed by an antiseptic.
• Black floor - edged board of natural humidity (spruce / pine AV) cross section 19/22 * 100 / 150mm, processed by antiseptic. Papohydrozolation - Nano-Isol C.
• Floor insulation - min. Wool Knauff / Ursa thick 100 mm. Parosolation - nanoseol "B".
• The finishing floor of the first floor is a dry tipped floor board (spruce / pine AV) 36mm thick. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• The outer walls and frontones are a frame of a natural humidity bar (spruce / pine AV) with a cross section of 40x100mm. The frame is processed by nonomid flabiopacket.
• Outdoor lining of walls, frontones - OSB 9mm moisture resistant panels. Wind-moisture protection - Nano-Isol A.
• Internal wall covering - lining (spruce / pine AV) 12.5 * 88mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• Partitions - a frame of a natural humidity bar (spruce / pine AV) cross section of 40x75mm. The framework of partitions is treated with non-oxyid firecase.
• Plugging partitions - lining (spruce / pine AV) 12.5 * 88 mm, on racks.
• The height of the ceiling of the first floor clean (from floor to ceiling) - 2.30m
• Ceiling liner - lining (spruce / pine AV) 12.5 * 88 mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• The second floor is attic (if provided for by the project). Ceiling height of the attic cleanness (from floor to ceiling) - 2.20m
• The height of the roof in the skate is 1.50 m (for single-storey projects).
• Warming-noise insulation overlap - min. Vata Knauff / Ursa, 100 mm thick. Parosolation - Nano Isola B.
• Mansard Floors - Dry Tinged Flooring Board (Wel / Pine AV) Thick 36mm. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• The walls of the walls and the ceiling of the attic - lining (spruce / pine AV) 12.5 * 88mm. Fastened along the rafters through the membrane Nanosol V.
• Uniard partitions (if any) - frame of natural humidity bar (spruce / pine AV) cross section of 40x75mm. The framework of partitions is treated with non-oxyid firecase.
• Plotting partitions - lining (spruce / pine AV) section 12.5 * 88 mm, on racks.
• Rafters - farms from a natural humidity board (spruce / pine AV) cross section 40 * 100/150 mm. The rafters are installed in increments of 800 mm.
• Roofroom roof - natural humidity board (spruce / pine AV) 22/25 * 100/150mm. Controlling - Bar 20 * 40 mm
• All wooden elements of the roof are processed by non-nomide flakes.
• Coating - steel profile sheets with polymer coating. Colors to choose from: RAL3005 "Red Wine"; RAL6005 "Green Moss"; RAL8017 "Chocolate" RAL7004 "Gray"; RAL5005 "Blue". Cruising vaporizolation - nanoseol C.
• The staircase on the second floor - on the assets of the planed timber, with wide steps. Railings and fence on the attic of the planed bruk 40 * 100 mm.
• Windows - wooden. Double glazing. Opening ingoing sash. Screw loops, swivel locks. Dimensions (height * width): 1200 * 600 / 1000/1200 / 1500mm; 600 * 600 mm.
• Interior doors - wooden, fillenteed, polished (spruce / pine AV). Size 2000x800mm. Pens, loops.
• The front door is steel, insulated standard.
• Open terrace, porch (if provided for by the project). Supports - planed timber (spruce / pine AV) cross section 100 * 100 mm. The fencing is a planed timber (spruce / pine AV) with a cross section of 40 * 100 mm with filling in carved bassines. The floor is a dry tank floor board (spruce / pine AV) 36mm thick. Must with self-drawing into each board. The boards are stacked with a step of 5 mm. Ceiling - Lining (spruce / pine AV) 17 * 90 mm.
• Sealing angles, joints, adjoins - plinth (spruce / pine AV) 40 / 45mm.
• Finish finish of windows, doors - platband (spruce / pine AV) on both sides.
• Hardware: Construction black nails, Construction and finishing nails and galvanized, selflessness.
• Delivery up to 400km from our base + Unloading of the Domocomplekt.
• https://yandex.ru/maps/10920/pestovo/?ll\u003d35.809228%2c58.596895&mode\u003drutes&oid\u003d1081678118&ol\u003dbiz&RText\u003d58.596895%2C35.809228&RTT\u003dAUTO&Z\u003d17
• Build a house on the customer's plot.

• The foundation is the refiner. 4 blocks of 200x200x400 in the end of the cement screed. The cabinets are installed on the rammed sandy pillow. Sand (or PGS) provides the customer.
• Waterproofing - rubberoid in one layer.
• The strapping is a natural humidity bar (spruce / pine AV) section 150 * 150 mm. According to the outer perimeter, the strapping is placed in two rows. The timber is processed by the protective composition.
• The clogging is a decorative trim of the base. Frame from bar 40 * 100 mm with a doomlet from the board 22 * \u200b\u200b100 mm. Flooring - profile steel sheets with polymer coating in the color of the roof. Singing around the perimeter of the foundation from the top edge of the strapping. Ventilation processes (producing).
• Floor lags - chamber drying board (spruce / pine AV) section of 150x40 mm, with a pitch of 600 mm.
• Black floor - edged chalkboard chamber drying (spruce / pine AV) section 19/22 * 100 / 150mm. Papohydrozolation - Nano-Isol C.
• The strapping, lags and roughing floors are processed by protective neomid composition.
• Floor insulation - min. Wat Knauf, 150 mm thick. Parosolation - nanoseol "B".
• The finishing floor of the first floor is a dry tipped floor board (spruce / pine a) 36mm thick. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• Outdoor walls and frontones - framework of chamber drying (spruce / pine AV) cross section 40x100mm. Assembly on nails using steel galvanized perforated fasteners.
• Outdoor lining of walls, frontones - OSB 9mm moisture resistant panels. Wind-moisture protection - Nano-Isol A. Butt panels are closed by planks.
• Warming of walls and frontones - Rockwill basalt plates, 100 mm thick. Parosolation - Nano Isola B.
• Inner wall cover - lining (spruce / pine a) 12.5 * 88mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• Partitions - frame from a chamber drying bar (spruce / pine AV) cross section 40x100mm. Warming-noise insulation of partitions - basalt plates Rockvul 100 mm thick.
• The covering of partitions - lining (spruce / pine AV) 12.5 * 88 mm, on racks through the membrane nano-insole V.
• The height of the ceiling of the first floor clean (from floor to ceiling) - 2.40m
• Ceiling liner - lining (spruce / pine a) 12.5 * 88 mm. Publishing - 10 * 30 mm. Ventilation clearance - 10 mm.
• The second floor is attic (if provided for by the project). The height of the Ceiling of the attic clean (from the floor to the ceiling) - 2,25m
• The height of the roof in the skate is 1.50 m (for single-storey projects).
• Warming overlap - min. Wat Knauf, 100 mm thick. Parosolation - Nano Isola B.
• Mansard Floors - Dry Plumbing Flooring Board (Spruce / Pine A) Thickness 36mm. Each fifth board is attached to self-drawing (for the possibility of feeding floors).
• The walls of the walls and the ceiling of the attic - lining (spruce / pine a) 12.5 * 88mm. Fastened along the rafters through the membrane Nanosol V.
• Warming Ceiling of the attic - min. Wat Knauf, 100 mm thick. Parosolation - nano-insole in
• The insulation of the monsard walls is Rockvul basalt plates, 100 mm thick. Parosolation - Nano Isola B.
• Attic partitions (if provided for by the project) - framework of chamber drying bar (spruce / pine AV) cross section 40x100mm. Warming-noise insulation of partitions - basalt plates Rockvul 100 mm thick.
• Sheathing partitions - lining (spruce / pine a) 12.5 * 88 mm, on racks through the membrane Nano Isolaz B.
• Slingers - farms from chamber drying board (spruce / pine AV) cross section 40 * 100/150 mm. The rafters are installed in a step of 600 mm.
• Disease roofing - chamber of chamber drying (spruce / pine AV) 22/25 * 100 / 150mm. Controlling - Bar 20 * 40 mm.
• Coverage - metal tile. Colors to choose from: RAL3005 "Red Wine"; RAL6005 "Green Moss"; RAL8017 "Chocolate"; RAL7004 "Gray"; RAL5005 "Blue". Cruising vaporizolation - nanoseol C.
• Device of the drain system from the roof (PVC daughter).
• Eaves and sinks of the roof of 300 mm wide - lined with clapboard (spruce / pine AV) 17 * 90 mm.
• The staircase on the second floor (for houses with an attic) - on the assets of the glued bar, with wide steps. Spacing pillars and balusters. Figure handrail and fence on the attic.
• Windows - PVC, white with single-chamber glass windows. Dimensions (height * width): 1200 * 600 / 1000/1200 / 1500mm; 600 * 600 mm.
• Interior doors - Wooden, Filöncated, polished (spruce / pine a). Size 2000x800mm. Pens, loops.
• Windows and doors are installed in the mounting boxes. Technological gaps are filled with mounting foam.
• The entrance door is steel, insulated, prestige. Size 2050 * 870 mm.
• Open terrace, porch (if provided for by the project). Supports - planed chamber drying bar (spruce / pine AV) cross section 100 * 100 mm. Fencing - planed chamber drying bar (spruce / pine AV) cross section 40 * 100 mm with filling in carved balusters. The floor is a dry tipped floorboard (spruce / pine a) 36mm thick. Must with self-drawing into each board. The boards are stacked with a step of 5 mm. Ceiling - lining (spruce / pine a) 17 * 90 mm.
• All the construction is processed outside and from the inside by flameless composition neomid. Including: outer walls and frontones, inner walls, floors, ceilings, hidden elements of the roof strength construction (rafters, doomle, controlling).
• Sealing angles, joints, adjoins - plinth (spruce / pine a) 40 / 45mm.
• Finish finish of windows, doors - platband (spruce / pine a) on both sides.
• Hardware: Construction black nails, Construction and finishing nails and galvanized, screws, perforated galvanized fasteners.
• Delivery up to 400km from our base in Pestovo, Novgorod region + unloading of the house complex. https://yandex.ru/maps/10920/pestovo/?ll\u003d35.809228%2c58.596895&mode\u003drutes&oid\u003d1081678118&ol\u003dbiz&rtext\u003d"&rtt\u003dauto&"amp ;z\u003d17
• Build a house on the customer's plot.

Frame house on one and a half years old, it is advantageous to build on a small plot. It has all the advantages of a two-story cottage, but costs cheaper. Due to the liberated area, you can build a garage. Such houses are suitable for permanent residence, well operated in winter.

The construction of the house on a century and a half is carried out due to extension over the first level of the mansard walls. This construction does not have a attic because it becomes part of the dwelling and is constantly exploited. In the configuration of the house there may be a cuckoo, a balcony, a bucket or other small forms of architecture - it all depends on the approved project.

Houses from the company "SK-Posad"

We build a two-way "turnkey" frame houses for more than five years. We work in Moscow and the region, we have a large list of advantages:

• own logging production, thanks to which we supply quality raw materials at good prices;
• experienced builder specialists who work in any field conditions;
• typical projects in the catalog and the development of unique at the request of customers;
• fast construction according to agreed periods.

Call and write to us to ask questions and order a house. For you, special offers always apply.

One-story frame houses appeared in the real estate market relatively recently. The unusualness of such buildings is in the second floor: it is incomplete, since the slinging system slightly sticks the walls and reduces the height of the house.

Company "PROFD 53" offers ready-made projects of semi-storey frame houses, each of which is unique. We are engaged in a comprehensive construction of houses at an affordable price. In our catalog, you can see photos of such objects with attic, verandas, terraces and other decorative elements that make the house beautiful and extraordinary.

Features of semi-storey houses

You can note a number of advantages of houses at one and a half floor:

• the area of \u200b\u200bthe second and first floors will be completely equal, so additional meters can be used for residential premises;
• the cost of construction is significantly lower than on the construction of a full-fledged two-story building;
• the use of a bar makes the structure easier, which allows not to apply a monolithic foundation during construction. This in turn also affect the price;
• the semi-power building of the wood has an unusual attractive appearance and looks worthily, no less inferior to houses made by traditional technology;
• due to the smaller work, the construction time is reduced to several weeks.

House at one and a half years - a favorable offer from "FDD 53"

Our company has been engaged in the complex construction of inexpensive household houses in the complex construction. Therefore, you can unconditionally entrust our specialists the construction of your home designed for year-round or seasonal stay.

Our projects made are always in demand, because they allow you to save not only money, but also the area of \u200b\u200bthe allocated land plot. We can, if necessary, add additional changes to the finished projects, offering other sizes, layout, the design of the foundation or overlap.

All our bar houses are manufactured in their own production, so we guarantee their quality and durability. Call us and in the shortest possible time you can stay outside the city in your own home one and a half.