"The woman is created for a man, not a man for a woman" - such a postulate ...
In the life of ancient Russia, used in the second century circles, Zhobanes, glasses and bowls. Such zhobans and the jets are almost unchanged and in our time. Zhibans for kvass, honey and beer are essentially large circles that accommodate near the liter of the drink. Usually they had drain spacing and folding covers. Of the larger Zhabanov, whose drain noses were not, drinks were dredied with special wooden brushing. The word Zhban is much an ancient word mug. If the Juban is necessarily a wooden coolest vessel, then the mug can be metallic, clay and others. The exceptions are measuring mugs that have a sufficiently large container. Modern dimensional circles have a capacity of 1 liter. The bucket accounts for 10 to 12 mugs.
Nowadays, glued circles are made, which at first glance are no different from the coolant. They are made of individual rivets and put the hoops. However, this is just imitation. The cow of the circuit is sharpened on the lathe.
For manufacturing wooden mug Of the triangular wooden prisms glue the massive block. After the glue dries, the hollow mug of the circle is pulled out on the lathe, along with a helm of a donkey, which is inserted onto the glue. After the calculation, each of the prisms acquires the form of a coolest riveting. Metal or wooden hoops are stuffed on the core and with the help of round plug-in spikes (wrens) attach a figured handle with a curly lid or without it.
Such a mug is similar to the coolant, but it cannot be used for water and drinks, as the glue can melt from moisture. Bondar dishes are not only completely harmless, but also contributes to the acquisition of special properties that improve their quality.
For the manufacture of mugs, nanes and other cooled vessels use wood ash, oak, linden, birch, alder, aspen, maple and juniper. The utensils made from juniper not only beautiful, but also useful. Her aroma resembles the smell of fragrant pepper. The aroma is so racks that retained for many years. It is absorbed and drinks poured into juniper dishes. From moisturizing wood fragrance increases. It seems that it proceeds not from the circles, but from the drinks themselves - kvass, beer, etc.
For riveting juniper vessels, trunks of dried juniper are blank. Juniper is a very light-affiliated plant. He does not like blackout, so it's not so difficult in the forest in the forest. Juniper trunks are thin and can not split out as it is necessary, but wood is well treated with a knife, rocks, stoves, cutters, and other tools. In order to save wood juniper rivets in the crucia, you can alternate with lime, olhov or aspen.
The best milk mugs made of wood Cedar and ate, as it is weakly absorbing the liquid. Special substances contained in cedar wood contribute to the good preservation of dairy products.
For Zhbanov, mugs, horsebacks and other coopers, the coils are made in the same way as for any cooler dishes having the shape of a truncated cone. Individuals will be proportions, dimensions, shape of the handles and covers.
In decorative vessels, the handle may have the most unusual form. For example, a knob, decorated with propyl carvings, gives the lump, a mug or a knife elegant beautiful view. Such dishes can decorate the interior of any kitchen.
For production of crushes with folding lid, in the upper part of the handle, as well as in the covers, the covered hole is drilled. In the handle, the hole diameter must be 1 - 1.5 mm less than in the covers of the cover. Then the round rod, isted out of solid wood, when connecting the handle with a lid, it will be firmly held in the covers of the cover, but freely rotate in the hole of the handle.
The handle is attached to the cozoi with a jack embedded in a riveting and top with hoops. If the rivets are thin, then instead of the fastening method, the other is used, in which the handle is cut out of a whole piece of wood with a riveting. After assembling the core, as it may be organically connected to it. The drain spout for the zhomban and horseradish is also cut together with a riveting of one piece of wood.
For lagunta manufacturing - Original cooler dishes, in addition to ordinary rivets, two special rivets are needed. The use of the product is narrowed up and has the shape of a truncated cone.
One of the rivets is cut together with the side handle, and the other is cut with protruding over the core. The second riveting at an angle of 45 degrees attach tubular spout. This riveting can also be cut from a single billet, which is a barrel area with a bitch of suitable sizes.
If the spout is made separately from the riveting, it can be chopped on the lathe or cut into a knife from the round. To do this, in curlers, gropped in vice, drill through a longitudinal hole. First drill from one end, and then from the other. The finished wooden tube is cut and inspited by a knife to give it a cone form. Then in the riveting, the hole is cut into which the spout is inserted.
The lid for the lagunca is best cut out of a wide board. But you can also make it from 2 - 3 skulls connected to each other on the knaps. On the one hand, the cover is connected on a hinge or swivel with a side handle, and on the other - with a small cover, covered spout. In the lid, the hole is hammered, in which there should be an eye-speaking riveting. To pour a drink to the vessel, we fold a large cover to pour away the small lid.
In the original core vessel, which is called the lagoon, the details of heterogeneous cooler dishes are used. Long tubular spout is borrowed from an ancient subsoil of the XIII century, the stick-bracket is the same as the birest tusk, a side handle, like the Zhuban, and a riveting with an eye, like a bucket or a tub. By closing the lid on the tape, the lagoon can be raised behind the handle-bracket, and also, if necessary, to transfer.
Thanks to the end of the long nose, the contents of the lagoon can be poured into the dishes with a narrow neck and in small dishes. The presence of two handles (side and top) makes it easier to break the drinks. For the top handle, the vessel is raised, at the side tip forward. Four rectangular holes are cut into the handle. Bottom holes serve to fix the handle on the lid. One of them should be a little less than the other. So that the handle rests on the lid and did not fail, small hangers cut out on both ends. The ends of the handle are inserted into the lid jacks and the birch clock is fixed, which is driven into the holes below.
The edges of the two other rectangular holes in the handle located above must be at the level of the surface of the lid. In these holes are inserted with a leak carved from a birch bar. One end of the junk should be included in the UCHO protruding above the riveting. If you pushed back from the easter, it will immediately open. So that it is convenient to move the tape to make your fingers, a semicircular cut is made in her block.
Usually the lagoons are made of fir or fir. The wood of these trees is lightweight and well processed. Finished dishes were painted with oil paints. Sometimes the hoops did not paint, but covered with oil. Slightly golden wood hoops highlighted on a multicolored background.
A vessel will be very elegant if you decorate it with carvings or burn pictures on it. Wood can be treated with a soldering lamp or burner, etc.
Materials
1. Wooden ram 10 inches (25.4 cm)
2. Mug hiking (stainless steel)
3. Linen oil
4. Cotton cloth x / b
5. Car glue or epoxy resin
Instruments
1. Wood lathe
2. Set of styers
3. Brush
4. Drill and 3 circular drills (to create a cavity in the workpiece)
5. Sandy paper
6. Hoven
7. LINEK
The process of creating a wooden mug with your own hands.
And so, first of all, of course, it is necessary to find a suitable material, better if the drawing and texture of the tree will not be uniform. For this, the breed of fruit trees (apple tree, cherry, cherry) are suitable. The drawing is very beautiful and unique. You can also use the "Cap" pattern of which is very similar to marble, but its wood is rather solid and difficult to process.
Then the workpiece must be dried under natural conditions. Or in a special drying chamber (who has it) Attention!Wood must be absolutely dry before processing, if it is not degraded and wet, and later she just cracks and all your work "cat under the tail"
Many of you at school in the lessons of the "Labor" learning in high schools, studied a lathe on a tree and pulled out on it (rollers, bales, candlesticks, door handles, etc.) that is, with the device and the principle known. But to the ultold on this machine (glasses and dolls) allowed not all, but especially neat and attentive! Because with the inaccurate work on the internal cavity, the workpiece often departed, where the doll, where the chisel))))
Next, the resulting bar need to be placed using a ruler and a pencil, in order to find the center by spending 2 lines from the corner to the corner, crosshairs and will be the center. The center must be strictly observed !!! Marking curve is a potential blow to the forehead broken by the workpiece))) By the way, here on the site there are articles on the manufacture of a lathe on the tree with your own hands
Inserted into guides and clamping.
The machine is turned on and the master begins to strike excess, giving the billet with a cylindrical appearance.
Important moment! On the left side, pulls the "spike" which later will be inserted into the clamping cartridge and will keep the blank without 2 points of the support.
Next, the inner cavity is drilled, the author for this uses 3 drills of different diameters, starting from the smallest. After the interior, it is necessary to stall with the help of sandpaper dressed on the stick, it is necessary for subsequent sharpening, in order to provide a flat surface.
With the help of the chisel, the inner part is pulled.
Periodically, the master applies a dyshko metal mug so as not to run extra. Once again, stopped the machine, in order to evaluate the work done.
The surface of the wooden glass is grinning using sandpaper.
And so, the inner part is flowing and now the master with the help of the knife is cut off.
Next, the master takes its marching glass of stainless steel and covers it with epoxy resin, you can also use glue not afraid of temperature effects. Attention!Do not use toxic types of glue by type "Moment" Because when you board the mug of boiling water, the metal will warm up and this glue will begin to evaporate its chemical elements. Be more close!
Epoxy-covered surface is placed in a wooden glass.
Then you should wait until the adhesive composition is dry, and then the wizard places the glass back into the clamping cartridge of the lathe, it is necessary for the maximum to align the bottom of the hike mug.
And one more strict instruction from the author !!! Do not cover the wooden surface by the mourn and all sorts of varnishes (because in their chemistry. He took the natural cloth x / b (cotton-paper) Mocked with oil and the machine impregnated with small turns of the machine. Why the master does it on the machine? Because the oil needs a long time and painfully rubbing the product (manually) and on the machine everything is prompt)
As you might notice the metal mug of the author has a lid, so in a wooden case with a closed lid, the liquid will remain hot or cold, depending on which it will be nalito. Accordingly, the mug became very beautiful and already unique, because the tree drawing is not repeated)
The work is certainly not simple, but the result is worth it. By the way, you can also wait for some kind of drawing, or the inscription, as they say "at your discretion."
From a wooden mug so nice to drink cool kvass on a hot day or after the steamkee's wage! I suggest make it with your own hands.
You will need a plate of hardwood wood: oak, birch, alder or other. The main thing, do not try to make a mug of pine, otherwise your drink will be designed by resinous aroma and bitterness.
You will need to eat 12 sheets of length 22 and 3 cm thick. One side of the plank should be shorter than the other width, so that the SCOS is 12 degrees:
When the plank is drunk, carefully polish them.
Now we take the scotch and collect the canvas, applying a plank to each other with the inner short side up. Take some kind of cylindrical pattern and promoting knockers with plow glue, start collecting our mug:
Castle tightly with ropes or elastic rubber band.
Carefully cast a mug outside and inside when the glue is completely dry. Count it with metal rings.
Cut out the bottom of the bottom, with such a calculation so that it is to be prompt, we will miss the bottom end of the glue and insert into the mug:
I drank the handle (by the way from the pine) and glue it to the circle.
All sharp details are cast and rounded the skin. You can handle the mug with linseed oil to give her beautiful warm shade. The main thing is not to use synthetic toxic compositions.
Please note this post:
As a basis, the stainless mastery of the wizard is taken here, so he decided to stylize it under the tree. For which it took a pre-dried billet from the tree (it is desirable that the texture has been beautiful) and extended a wooden glass on the lacker, in which he inserted his beloved metal mug.
Let's look at how the master did his mug? What exactly did it need for this?
Materials
1. Wooden ram 10 inches (25.4 cm)
2. Mug hiking (stainless steel)
3. Linen oil
4. Cotton cloth x / b
5. Car glue or epoxy resin
Instruments
1. Wood lathe
2. Set of styers
3. Brush
4. Drill and 3 circular drills (to create a cavity in the workpiece)
5. Sandy paper
6. Hoven
7. LINEK
The process of creating a wooden mug do it yourself
And so, first of all, of course, it is necessary to find a suitable material, better if the drawing and texture of the tree will not be uniform. For this, the breed of fruit trees (apple tree, cherry, cherry) are suitable. The drawing is very beautiful and unique. You can also use the "Cap" pattern of which is very similar to marble, but its wood is rather solid and difficult to process.
Then the workpiece must be dried under natural conditions. Or in a special drying chamber (who has it) Attention!Wood must be absolutely dry before processing, if it is not degraded and wet, and later she just cracks and all your work "cat under the tail"
Many of you at school in the lessons of the "Labor" learning in high schools, studied a lathe on a tree and pulled out on it (rollers, bales, candlesticks, door handles, etc.) that is, with the device and the principle known. But to the ultold on this machine (glasses and dolls) allowed not all, but especially neat and attentive! Because with the inaccurate work on the internal cavity, the workpiece often departed, where the doll, where the chisel))))
Next, the resulting bar need to be placed using a ruler and a pencil, in order to find the center by spending 2 lines from the corner to the corner, crosshairs and will be the center. The center must be strictly observed !!! Marking curve is a potential blow to the forehead broken by the workpiece))) by the way, here on the site there are articles on the manufacture of wood with your own hands
Inserted into guides and clamping.
The machine is turned on and the master begins to strike excess, giving the billet with a cylindrical appearance.
Important moment! On the left side, pulls the "spike" which later will be inserted into the clamping cartridge and will keep the blank without 2 points of the support.
Next, the inner cavity is drilled, the author for this uses 3 drills of different diameters, starting from the smallest. After the interior, it is necessary to stall with the help of sandpaper dressed on the stick, it is necessary for subsequent sharpening, in order to provide a flat surface.
With the help of the chisel, the inner part is pulled.
Periodically, the master applies a dyshko metal mug so as not to run extra. Once again, stopped the machine, in order to evaluate the work done.
The surface of the wooden glass is grinning using sandpaper.
And so, the inner part is flowing and now the master with the help of the knife is cut off.
Next, the master takes its marching glass of stainless steel and covers it with epoxy resin, you can also use glue not afraid of temperature effects. Attention!Do not use toxic types of glue by type "Moment" Because when you board the mug of boiling water, the metal will warm up and this glue will begin to evaporate its chemical elements. Be more close!
Epoxy-covered surface is placed in a wooden glass.
Then you should wait until the adhesive composition is dry, and then the wizard places the glass back into the clamping cartridge of the lathe, it is necessary for the maximum to align the bottom of the hike mug.
And one more strict instruction from the author !!! Do not cover the wooden surface by the mourn and all sorts of varnishes (because in their chemistry. He took the natural cloth x / b (cotton-paper) Mocked with oil and the machine impregnated with small turns of the machine. Why the master does it on the machine? Because the oil needs a long time and painfully rubbing the product (manually) and on the machine everything is prompt)
Pick any round capacity of the same size as you want to make your mug. Place the bars around it and connect them with a sticky ribbon. Leave the last section open, that is, do not complete the circle.
Now spread the resulting workpiece on a flat surface and apply some glue into the space between the bars. Recall the product again by forming a circle. To tightly fix the boards, use a thick rope and several solid items that will be at hand, such as screwdrivers. Tight wrap the product with a rope, tie to several ends solid objects for weighting. The main thing is to create a pressure between the details so that they are tightly in contact. Leave the product in this position to give glue.
Now you need to make a handle for our mug. Approximate size of 20 cm x 8 cm. It is best to pre-make a sketch. Transfer it to the blank for the handle, carefully cut down. Perform the grinding the part with any grinding machine. When the glue will dry out, you can polish the surface and the mug itself. To give a more natural and original species, decorate the mug with strips of a small width sheet. It is best to fasten the item to the bar at the base of the handle. You can also use decorative laces, rings, cut the surface pattern. In general, the personality of the mug will depend on the fancy of the wizard.
Sanately attach the handle to the main part of the mug. Make it with glue, liquid covers, self-tapping screws, etc. Then cut the bottom of plywood or more solid material. It should be approached by size, but it is not worth it too much to approach its processing: no one is going to drink from the circle, which means to provide a reliable docking with the frame optional. Police work ready.
