The Chinese have long believed that a kite soaring in the sky takes away all illnesses, hardships and worries. In addition, kite launching is always a spectacular and fairly simple activity. The main thing is to choose the right place and take into account some of the nuances.

What kid doesn't dream of flying a colorful kite? What could be stronger than the delight with which children watch a toy soaring in the sky? "Daddy, let's make a snake!" - says the beloved child. And the father scratches the top of his head in concern, because assembling a kite and flying it seems to be something especially difficult. But it's not like that at all.

Theoretical minimum

Before you fly a kite, you need to familiarize yourself with the basic concepts:

A rail is a thread with which a flying toy is controlled;

The bridle is a strong thread woven together, thanks to which the kite is attached to the lifeline;

Bearing area - the size of the projection of the kite on a horizontal surface;

Bearing capacity is the lifting force of one unit of bearing area;

The center of pressure is the center of the bearing area.

How to make a toy fly?

How to make a kite so that it soars? To do this, its surface should not be flat, but should bend upwards under the pressure of the air flow. That is why, when making a kite, it is not recommended to stretch the material (paper, oilcloth, fabric) too tightly. Sometimes it is enough to fix only the corners. The center of gravity must be shifted towards the tail, otherwise a long hover cannot be achieved.

The leading edge of the kite must be carefully taped or reinforced to avoid eddies. For those who do not yet know how to fly a kite, it is better to give preference to flying models that have a long tail - it gives the correct balance to the whole structure.

Another important element- this is a bridle, which should consist of two threads. But such a kite is quite difficult to manage, so it is better for beginners to use a triple bridle.

Home workshop - manufacturing steps

1. To assemble the simplest type of kite, you need to take two thin pine, bamboo or plastic slats 30 and 50 cm long. Measure 15 cm from the end of the longer slat and fasten a small slat at a right angle with strong threads. Thus, a crosspiece for a flying toy is obtained.

2. At the ends of the planks, you need to make round notches into which a thin, strong thread is pulled. You should get a quadrangular frame.

3. Then you need to take thin paper or oilcloth and fit the existing workpiece. To do this, the resulting frame is placed on a sheet of prepared material and circled with a pencil or marker, adding a small distance to the allowances for fastening.

4. The pattern is cut out, after which the frame is well smeared with glue and attached to the material. You can decorate a kite with felt-tip pens, drawing cartoon characters on it (which will please your children), or depict the slender legs of your beloved woman on it (which will please you).

5. Now you can start attaching the bridle. For this, a spool of fishing line is taken, which is attached to the left corner of the workpiece. Then it must be stretched to the nose of the snake, and from there to the right corner to determine the length of the bridle. Cut the thread and attach the tip to the right corner of the snake (it turns out a long thread from one end to the other). Now we take the spool again, fix the fishing line in the bow of the structure, measure the distance to the left corner of the kite, add another ten centimeters, cut it off and tie it to the middle of the first thread.

6. The tail of the snake can be made from a thin cord or a strong nylon thread, measuring 3.5-4 meters. The tail can be decorated with paper bows.

7. Launching a kite is impossible without a leer. To do this, a long strong thread is attached to the bridle, at the end of which you can tie a small stick for ease of control.

Flat flying structures

Such kites are the simplest and most famous. The frame is made of pine or any other light wood. Sheathing is made of film or paper. Paper does not provide structural stability, so it must be durable (mica, cigarette or rice paper). If a film is used, then it should stretch poorly, but at the same time stick well to the frame (it is best to buy acrylic).

What does a monk serpent look like?

Such a flying layout got its name due to its similarity with the hood of a monastic cassock. Such a kite is perfectly centered, so a two-lead bridle is enough to launch it. The tail is used as a balancer, it should be light and thin. The material for such a kite is better to choose dense, because under the gusts of wind it is too easily crushed and falls.

Archery flying structure

This is one of the varieties of flat kite. The frame is built from a pair of rails, which ensures lightness. In this case, the front rail gives rigidity to the entire structure, but there is a greater sensitivity to the wind. Beginners are not always able to master the first time flying this type of kite.

box design

This type of homemade snake looks pretty solid, but it is quite simple to perform. He doesn't need a tail. What's more, these snakes can lift small loads, making it possible to place a small digital camera in them, after turning it on for video recording or continuous shooting. In this way, you can get completely unique shots from a bird's eye view. But the box-shaped design keeps well in the air only when strong wind.

How to fly a kite: choose a place

So that nothing interferes with the flight process, you should choose open areas without any obstacles. Trees, kiosks, buildings located nearby interfere with the direct passage of air currents and create unnecessary turbulence. The sea coast with its breeze is perfect (unless, of course, you have to jump over the bodies of vacationers at the same time). It is better to stay away from highways, airfields and power lines.

How to fly a kite (instruction)

First you need to determine the direction of the wind by simply drooling on your finger. Now the kite is solemnly handed over to a friend (girlfriend, child, wife). You need to stand in front of your assistant, who should hold the kite above his head, perpendicular to the ground. The wind should blow at your back, the reel with the lifeline should be in your hands.

So how do you fly a kite? First you need to slowly move away from a friend at a distance of about 20 meters, while unwinding the leash. Having given the command: “Let go!”, sharply pull the rail towards you. With a good wind force, the kite will soar in the air itself, and all that remains is to enthusiastically watch its flight. Otherwise, you will have to run around the field a little more until the structure catches the air flow.

How to fly a kite in different wind strengths? If it flies only when the person driving it is running, then the wind is too weak. With fairly strong air currents, the flying structure soars in the air with ease, and no additional effort is required. The optimal wind speed for launching a paper layout should be 3-6 m/s.

If the tension of the thread-leash is too strong, then it should be unwound a little. If the wind subsides, then the snake is pulled to itself. To return the structure to the ground, it is necessary to gradually wind up the rail and go home with a sense of accomplishment.

(http://nepoceda.com/kak-sobrat-vozdushnogo-zmeya)

Basic elements of a snake

Frame - depending on the model, it may consist of two or more rails. The mutual arrangement of which depends on the specific model. Serves for structural rigidity during flight.

Cloths - light fabric, cellophane or paper, which is covered with a snake frame. Due to this, there is an obstacle for the wind that creates lift. The canvas is placed in relation to the wind in front of the frame.

Tail - usually made in the form of one or more ribbons, and even with bows. Serves not only as a decoration, but also to smooth out imperfections during the flight. The tail is not found in all models.

Bridle - for attaching a thread (leera) to a kite. They are of several types, depending on the number of attachment points:

with one - does not require adjustment, the tail does all the work

with two or more - there is usually a regulating part (ring) here to adjust the angle of attack by the wind.

with a keel - a single piece connected to the canvas of the same material, instead of a bridle with two fasteners. Does not require adjustment, usually a tail is hung for this purpose

Leer (thread, rope) - with its help they control the flight. It should be light and strong, preferably with the ability to unhook from the snake. For this purpose, they put carbines for the tail, by the way, too.

Coil - for winding thread (handle). Facilitates use and less risk of tangling the rope.

Consider the possible options:

1. If you have a rail (twig) and a bridle, a reel, a tail in the kit.

Take the frame of the snake, insert the bridle from the front side into the holes on the snake. (for an example, see the picture above) - Turn the kite over and thread the rail into the holes (loops) at the ends of the bridle. - Next, find the special slots for the slats on the kite. They (grooves for the rail) should be located along the edges either from top to bottom or left to right. behind the canvas during the flight. - We turn the kite over to ourselves with the front side of the kite and tie the thread to the bridle. - If there is also a tail, find a hole at the bottom of the snake and fix the tail.

2. If there is no rail, but there is a bridle, a spool of thread, a tail is not a mandatory attribute. - Then just look for holes on the snake and fix it (bridle). - Next, attach the thread to the bridle. The fastener of the thread to the bridle should be on the front side. - We fasten the tail, if it comes separately. It may not exist at all.

3. Perhaps in the kit there will be only one spool of thread without a bridle but with a rail and a tail. Your model with a keel is a one-piece piece connected to the main web of the snake. - The keel should have a hole for tying a thread, or some other device - a carabiner, etc. For clarity, consider an example. in our case, it is necessary to thread the thread into the hole on the keel. We fix the thread by tying a knot. - On the reverse side, turning the kite over, insert the rail. As described above, the rail is inserted into the special. recesses along the edges of the snake (bottom-top, right-left, or, if two slats, both). - Such models are also equipped with a tail, which also comes separately, attach it, there should be holes for attaching the tail from below. in our case, it is a metal hook with a loop.

4. For models with two rails or more, the assembly principle is similar. Depending on the number of additional rails included. They are inserted into recesses on the snake. Location may vary. How to be perpendicular to each other, intersect, be parallel.

What could be better than a wide open field, a warm light breeze and a kite dancing in the air?

We present you a training manual, which is useful for all novice pilots. There will be some science, physics, history and culture. For adults, this is a chance to plunge into youth again.

Flying a kite is fun, but only if you know how.

Here the kite behaves calmly and with minimal effort. It is mainly used for short breaks while driving. window perimeter. This is the area where you need to land. flight area. This is the so-called "power zone" where the wind exerts the most pressure on the kite.

Kneel on the ground with the wind blowing from your back. Spread the kite as its nose is pointing towards you and its "belly" is up. This position will push the kite to the ground. Once you have the kite assembled, turn it on so that it rests on its "belly", with the nose on the ground. Move in the direction of the wind, unwinding the ropes.

Environment

Kites love open space. The more open the place you have chosen to fly, the better the kite.

The wind, which has to bend around trees, buildings or hills, becomes uneven and rough. This is "turbulence".

You won't be able to see it, but it will be difficult for the kite to fly and perform tricks in such conditions.

Note. Kites that are opened for the first time require a little "exercise" before they can reach their full potential. Seams and knots should lie down, and the fabric should stretch well. Depending on the wind power, this can take 1-4 hours. Body position As with other sports, body position is very important for driving success. Stretch the ropes and keep them parallel to each other. Stand slightly with your arms crossed at the elbows and forward. Depending on the strength of the wind and the size of the kite, be prepared to move forward as you fly the kite.

Therefore, the first advice is to choose a place as far as possible from all sorts of obstacles that interfere with the smooth passage of the wind.

Everyone heard of "Tree-Eater-Kites"?

Make sure that there are no trees in the path of the kite, they do not interfere much with piloting, but a kite flying by can get into the air flow around the tree. As a result, he will get stuck between the branches and have to call the fire brigade to save the poor fellow...

It's like you're pulling ropes. Often beginners open their arms or raise them. This is the wrong position, so the kite is more difficult to control. Another common mistake is overhandling. There is no reason for this. Regardless of the direction of the kite, keep your hands parallel to each other when you hold the wheel on the bike.

Management If you pull the rope into your right hand, the kite turns to the right if you pull left-left. Keeping the arms in a neutral position, the kite continues in its current direction until it reaches the edge of the window. When handling the kite, first try to keep it a few times, near the zenith. Use slow, relaxed movements until you get the hang of it. If the kite is spinning and turning your ropes, don't worry, keep steering. Modern ropes allow multiple turns without affecting driving ability.

And, of course, avoid proximity to dangerous objects, such as highways or power lines.

The best places to fly a kite - large open field, park or beach. The more open space you find, the more fun and less trouble you will have.

Wind

A kite needs wind to fly. How strong depends on the type of kite you are about to fly.

Here are some numbers that may impress observers. They are in a difficult position in four categories. For more information about each of these, you will need to get more information online. The power kite is usually an aerodynamic wing made of high quality material and controlled by rudders. When steering and maneuvering the kite in the control beams, different levels of force are generated. When the kite inflates its aerodynamic shapes, it forces it forward and up.

Some are heavy, respectively, require the presence of a strong wind. Others are specially designed to fly in light winds.

However, most kites are designed for use in the medium ranges of 1.5 - 5 m/s.

In most cases, you can determine the strength of the wind yourself, guided by your own feelings or observations of the behavior of the leaves on the trees. If the leaves barely move, then most likely it is too weak a wind, and if the whole tree sways and you can hear the linen flag fluttering, then it is even too strong.

The control line keeps the kite at an appropriate angle to the wind, thereby achieving the speed and power of the kite. The larger the arrow, or as soon as the kite is moving, or the stronger the wind, the more thrust is generated. The fighter who controls the kite takes over full responsibility for the safety of yourself and others during the flight.

The wind window is the area in which the kite flies without pushing the fighter into the air. In this window, a variable value and a different direction of movement are generated, maneuvering the change. The force decreases sharply as the kite approaches this window. If you are not sure how much force will be generated, a safe kite will be released.

Also, you can use special devices for measuring wind strength.

Experienced pilots eventually get used to judging the wind by eye on the effect on surrounding objects.

Kite

There are many varieties of kites. Each type was originally designed for specific purposes.

To ensure the safety of the kite, hold the kite at the edge of the windshield and maneuver it away from you to the power zone. If your skills do not allow you to fly the kite, modern kites have a safety system that allows you to reduce the attractiveness of the kite without leaving the kites.

Such a kite is designed to create significant attraction. However, in humans, the classification of kites based on their use and the name of the kites has evolved more frequently. The kite sport of this power was widespread much earlier than water damage. They ride on hard surfaces. These sports are very close to kiteboarding, kitesurfing and snowboarding and are equally attractive and give a huge dose of adrenaline.

These can be simple diamond-shaped (diamond), triangular (delta), box-shaped (box), inflatable (parafoil) or controlled sports with two or four handrails.

Before launching, make sure your kite is suitable for the current wind strength, if the kite needs a tail, if the lifeline is firmly attached.

What is the difference between two ropes and four?

At the same time, these are the only kinds of shaking when it comes to summers and winters. Two-rope kayaks are controlled in the simplest way without the possibility of pausing the kite. In this case, it is necessary to take into account the possible maximum wind speed and the energy that it generates. Four course kites have more control and are best suited for active mating such as bumpy, roller or snowboarding.

The top ropes are strength ropes. By controlling them, the kite is controlled and its energy is generated. The bottom ropes are brake ropes that allow you to change your speed by pushing them towards you. Brake cables also make it easier to control runways and takeoffs.

If everything is in order, you are ready to launch.

launch

Running with a kite is fun but not too smart, you can't watch where you're running and enjoy the sight of the kite at the same time.

Such a flippant approach can lead to trouble for both you and the kite.

What is the difference between four rope control cables and 4 rope feeders?

Four rope handles allow you to safely, easily and accurately control the kite with maximum maneuverability. Four rope handles allow you to suspend the kite, keep it in the air, flip the kite over or lower it safely to the ground. If the kite has landed with its "nose" on the ground, the kite can be flipped over by pulling the brake lines and then be airborne again. This kite handling is most suitable for bumpy, snowboarding or leisure boarding.

The four lanes usually have a special safety system that allows you to pick up and release the kite. Aitvaro's power is distributed equally to both hands, so it's easier to fly, but at the same time, you have less control over the kite. This is due to the special control of the bar and the rope system, which can be adjusted to different lifting power and wind speed. Raising the bar will increase the power of the kite.

Instead, try a smarter approach.

Stand with your back to the wind and lift the kite as high as you can. Make sure the kite is "looking" straight up and release it easily. Do not overdo it, do not try to "throw" the kite into the sky, just let go and let it fly on its own.

If the wind is strong enough, the kite will rise into the sky and start flying. Slowly pull the rail and the kite will fly back towards you.

You will need an energy kite, a helmet with an articulated pole, a board, a harness, a life jacket

Using the hood type for kites requires a trapezoid. Damage is an extreme sport, so we recommend starting with a kite kite. You will not only learn how to safely manage changes, but also get to know kite makers, kite models. Experienced instructors will help you choose the right equipment.

Each manufacturer has several types of kites in its range.

Within a few years, it was named the king of the surf kite category. This kite gives you a great feeling for breaking waves.

Then, just before it hits the ground, let go of the rail and the kite will rise up again. All you have to do is repeat this process until the kite is caught in a steady stream of wind.

In light winds, you may need the help of a friend. Ask him to hold the kite at a distance of 15-20 meters from you and release it as soon as you pull the rail. The kite should rise into the sky in the same way as if you released it yourself in a stronger wind. Soon, the kite will rise into the zone of stronger wind and the difference will disappear altogether. This will make you look much "smarter" than people running around trying to help the snake fly.

flight control

Watch the kite continuously as it flies. If something goes wrong, you will have time to do something to avoid aggravating the situation until the structure breaks. Resist the temptation to let go of the rail too much: 30-60 meters is enough. At long distances it is quite difficult to observe the flight for you and the surrounding observers.

If the line is loose, tighten it, if the line is too tight and the kite is unstable in the air, let it go a little. The main purpose is to pilot the kite, not just let it fly.

To complete the process, start slowly winding the line onto the spool. If the wind suddenly weakens, you can do it faster. As a result, throw the lifeline along with the kite to the ground so that the lifeline lies freely in the open space, this will soon allow it to be lifted into the air again without additional difficulties.

In strong winds, it may be necessary to attach the lifeline to an anchor on the ground, as well as use gloves to avoid damaging your palms.

Remember that tension on the lifeline increases the force of the wind on the kite. If the kite is behaving unstable, do not pull the lifeline even more, trying to bring it closer to the ground. Instead, loosen the tension and let the kite rise freely higher into the sky before pulling back gently.

If the kite began to rotate in a large loop closer and closer to the ground, once again, when it is close to the ground, pull it towards you, this additional effort will land the snake on the ground. At this point, you will surely be glad that you did not let him go too far.

Leer

You can buy a leer in the same place as the kite itself. Quite often, kites are supplied with the lifeline, although this is not always the case.

Special lifelines are usually lighter, stronger and thinner. All these qualities have a positive impact on the piloting process. Ideally, it's best to use the thinnest lifeline that the particular type of kite can support.

Adjustment for different wind strength

Many kites can be "fitted" to a specific wind force. Adjustment is carried out by changing the point of attachment of the rail to the kite. By moving the attachment point, you change the angle of the kite to the wind.

The larger the angle, the better the kite will be able to fly in strong winds, the smaller the angle will allow the kite to fly even in a light breeze. Too large an angle can cause the kite to flip over in the wind and break, too small will prevent the kite from flying.

Experiment! You will be surprised how such a small change can make a big difference in flight quality.

Tail

The design of many kites suggests the presence of a tail. The long tail, fluttering after the kite, is an undoubted decoration. overall picture. But tails also have a practical value: the added weight towards the bottom tilts the kite up with its leading edge and provides better flight stability.

Thus, if your kite is unstable, try adding a tail, and vice versa, if the kite turns over and falls to the ground, you need to reduce the length of the tail or remove it altogether.

Tails are good for balance. One tail should be attached in the center of the kite next to the lifeline, two tails should be attached symmetrically on the sides, also make sure they are the same length/weight.

Problems

Even an experienced kiter sometimes encounters a tangled lifeline or finds his kite hanging from a tall tree.

Do not panic! Keep calm and everything will be fine

A snake in a tree? Don't try to climb up, if you fall it will hurt. Yes, and do not pull the rail, it is unlikely to help, rather harm.

It is best to let go of the rail and wait until the wind blows the kite through the tree. After that, unhook the kite from the lifeline and pull out the lifeline. back.

If your kite's line gets tangled up with another kite's line, just walk up to the owner and say hello. Surprisingly, both tangled lifelines will descend to the ground right to the place where you both will be standing.

And what if the rails are intertwined on the ground? In principle, you can avoid this ambush by handling them carefully, but if it does happen, all you can do is carefully unravel the ball. Life is not perfect

The kite doesn't fly?

Not all flights go smoothly. If your kite won't fly, you may be experiencing one of the following problems:

1. "Wrong" wind. Maybe too weak or too strong. The required wind strength depends on the kite, if there is a tail - try to unhook or attach a longer one.
2. Turbulence. Trying to fly a kite near a building or big tree? Not sure it's going to happen.
3. "Reconfigured". Maybe you or someone else has already adjusted this kite to a different wind and left it that way? Try to return as it was.
4. "Circle". If the kite is circling, try adding a tail or moving the anchor point of the lifeline.
5. "Lazy". If the kite does not want to rise into the air, unfasten the tail, move the attachment point of the lifeline. Maybe the rail got wet?
6. Technical difficulties. Make sure the kite is assembled correctly, read the instructions again. Safety

Every pilot should be concerned about safety. A kite that has lost control can cause physical harm to a random person.

An unwound lifeline lying unattended on the field can be a danger to passers-by people or animals.

Please be careful when flying the kite around other people.

In particular, never launch a kite across the road, if the kite lands on the ground and the rail crosses the road, this may cause a road accident. Never fly near an airport or power lines.

Be polite and courteous to your neighbors, good pilots always treat other pilots with respect, and even strangers.

Remember that the sky is a shared resource, try to be sensitive to competitors for the attention of viewers.

So you will get much more joy and pleasure!

(c) David Gomberg. GKPI.

Translation - IM "GlavZmey"

The idea to launch a ready-made kite is in the air.

1. When choosing a place to fly a kite, you should pay attention to open areas. Any nearby wind barriers, trees, stalls, statues of leaders, etc. the wind will be turned away from the true path and will give it unnecessary turbulence. Ideal for sea coast kites. But if you have to catch the breeze by jumping over the bodies laid out on the beach, you can look at other spaces. The selected glade should not be located next to a busy highway (glider pilots often run with their faces up to the sky and pose a danger near roads) and away from power lines and airfields.

2. Having slobbered your finger, find out the direction of the wind. Give the kite to your friend, whom you prudently took with you, and stand opposite him, but so that the wind blows at your back. Let the reel with the handrail be in your hands. Take a few steps back, unwinding the line. Please note that a friend should not type SMS at this time: the snake must be held with both hands above his head, trying to position it perpendicular to the direction of the wind.

3. Having moved 15-20 m away, shout to a friend: “Let go!” - and pull the handrail toward you with a jerk. If the wind is decent, the kite will rise up on its own, and you will be left standing with the coil, joyfully watching its flight. Otherwise, you will have to run a few more meters until the kite catches the wind.

4. If the kite only flies when you are running, then the wind is weak today. Even if it’s a shame to admit it after the marathon distance that you just completed with a lifeline in your hand. In a normally blowing monsoon, the flying structure flutters in height as long as it is simply held at arm's length. The wind speed of 3-6 m/s is considered optimal for a beginner. At a lower speed, only the lightest structures will be able to rise, at a much higher speed, the kite will be torn from the hands and will be subject only to a specialist kiter.

5. If the rail pulls strongly, you need to unwind the coil a little. Flight with a subsiding wind is regulated by pulling the kite towards you. With a successful combination of circumstances, the kite will hang in the air for several hours, and you will have time to take a break from the hustle and bustle.

6. In order to finally go home, the snake is pulled to the ground, gradually winding the rail. Announce to the children and onlookers gathered around that today you will not start anything else, except for the engine of your car. It might help them to break up.

And again, hello everyone! warmth has finally come to us, and with it, our most favorite entertainments - picnics in nature, family outdoor activities and conscientious feeding of mosquitoes - have moved into life with a slender gait. But with the latter, we somehow learned to cope with the help of any means. With picnics and campfire menus, we will someday seriously deal with it. Here's what's on our agenda today: active games with kids. One of them is launching a kite into space. And therefore, I declare the creative workshop open. And there, very soon, a kite will appear with your own hands, drawings with dimensions. Forward?

Materials and tools that can be used for construction

The beauty of this craft is that with any material that you have at home, you can choose the right model for yourself. And I will convince you of this now!

First, I will give a small good example. Windy weather occurs periodically in cities. This is when the wind blows and blows for days, blowing away everything that is wrong. Various light objects soar upwards, absolutely, as well as down from the balconies, it breaks all kinds of things. But one day the wind stops. And there comes a period. Which I call "Chinese lanterns". Indeed, the trees are neatly “decorated” with plastic bags. And why? Yes, because all these windy days, the bags were carried on their own, no worse than gliders. Got the idea? Then I will develop it.

From what you can build an aircraft "apparatus":

• from paper;
• cellophane package;
• thin tracing paper;
• old umbrella;
• from fabric;
• and even newspapers and magazines will be used.

So, look around and you will realize that you have the most basic material. But what else is needed in order to make a design:

• Main material;
• Thin planks. These can be hollow metal rods, bamboo sticks, or vine branches (they are lighter than usual);
• Scotch tape or glue;
• Rope, fishing line or strong thread;
• Spool to adjust the length of the thread;
• Scissors.
• Pattern.

I want to say right away that the model, as well as the complexity of the craft, will depend on how old our little one is, for which we are making. And the conditions under which we do it. For example, if the baby is very, very small and cannot run around the field flying a kite, but we want to give him new emotions, or if we are already in open field, and before that we didn’t plan to do anything, because we don’t have even half of the list of materials, you can still come up with something.

Ideas and DIY

Craft for kids

For example, here is the most elementary, but no less cool craft:

1. take a simple plastic bag;
2. tie a thread of her handles in the middle.

It remains to catch the wind! It is so simple! But believe me, the little one will be greatly delighted. Moreover, you don’t have to run much, the kite “puffs up” itself and takes off, as soon as the breath of the breeze touches it. True, it will not fly high, but children under 5 years old will still be interested.

But let's talk about something more complex that can be done at home with our helpers.

Paper kite that flies high in 5 minutes

This option seemed to us the simplest and fastest, so we immediately made it at the first wind. I really liked it, and my son, and even my husband, although he was very skeptical.

Details in our video:

The simplest kite design

All the same package, or rather, I will describe with the package, but instead of it, you can use any of the above materials.

We will need:

• Package - 1-3 pcs. (depending on their size);
• Wooden sticks (we choose light ones) - 2 pcs.;
• Scotch;
• Knife and scissors;
• Fishing line;
• Glue;
• Marker;
• Coil;
• Strong rope.

Manufacturing:

1. We cut off the sticks so that we have one 60 cm, and the second - 35. Fold them crosswise. We put the one that is shorter on the long one, retreating 15 cm from above. We fix them by bandaging with tape.
2. We cut each edge of the stick in the middle to a depth of 1 cm. wrapped with adhesive tape under the notch. So the design will be more durable.
3. We stretch the fishing line into the cuts and pull it.
4. We wrap it with tape several times to secure the fishing line.
5. We fold the packages, perhaps if they are too small, they will have to be firmly glued to each other to get right size. On top of the cellophane "canvas" we put the "skeleton" and circle it. Adding 1.5 cm of cellophane to the fold on each side, cut out the base.
6. We attach the frame to the base and tuck the edges. We fix them with tape.
7. We tie a 50 cm fishing line to one and to the second edge of a short stick.
8. We also tie a rope 25-40 cm to the top of the layout. Its length will depend on the slope of the kite you choose. If you want the structure to fly almost horizontally, then its length should be minimal; vertically - maximum.
9. We tie the middle of the fifty-centimeter fishing line to the fishing line that is fixed at the top.
10. We tie a rope to the junction of the woods. Secure it firmly with tape.
11. We decorate our aeronaut. Another rope, small, about half a meter, on which cute bows are tied, we tie to the lower end of the frame.

We draw a picture on the “front” side of the base.

According to the same scheme, but with other materials of construction. Cocktail tubes, paper and rope are used here.

Based on materials

Parchment paper kite

For work you need:

• parchment paper 36*51 cm;
• wooden sticks or light slats: 2 x 60 cm, 48 cm and 36 cm;
• colored crepe paper;
• strong thread;
• reel with fishing line;
• glue stick and PVA;
• a small metal ring;
• scissors.

Fold the parchment sheet in half, so we outlined the middle line. Along the top edge of the narrow side of the rectangle, place the smallest stick, stepping back from the edge by a centimeter. Lubricate the free edge of the sheet with glue and wrap it so that the stick is inside, it should be tightly fixed.

Lubricate a stick 48 cm long with PVA and glue to the center line of the workpiece.

Lay the remaining sticks along the diagonals of the rectangle.

Glue them with pieces of paper, as shown in the photo.

Cut out squares or arbitrary figures from colored paper and stick on the front side of the rectangle.

On both sides of the intersection point of the diagonals, make a hole.
With pieces of thread, tie the ends of the sticks at the upper corners of the rectangle, pulling them together a little.

Tie a long piece of thread to the upper right corner of the kite. String a ring on the thread, it will help control the flying machine. Then thread the thread through the holes previously made in the center of the rectangle and pass it through the ring again. Tie the end of the thread to the upper left corner of the product.

Tie the end of the line tightly to the control ring.

Glue long strips of corrugated paper to the bottom of the kite. These "tails" will help him balance in the air currents. Them optimal size 5cm*2.5m.

The air wanderer is ready to surprise you with its flight characteristics. Good luck with your flight!


DIY simple box kite

Serpent Rokkaku

More serious design.

Convenient snake reel

Draw a circle with a diameter of 20 cm. Cut out two such blanks from cardboard. Cut comfortable finger slits on them, they should match exactly on both circles.

Cut several strips 2.5 cm wide.

Mark the inner circle, use a compass or a suitable template.

Fold the cut strips along the contour of the cutouts, glue with hot glue.

Glue the inner ring in the same way.

Glue the second circle on top of it.

Glue the end of a long thread to the inner surface of the spool and wind the thread.

So that it does not get confused, tie a match to its end, fix it with glue. Insert the thread into the slot on the outer ring.

With such convenient fixture your flying kite will conquer not only the sky, but also the hearts of your children.

* based on materials

mechanical bird

Not quite a kite, but also flies. And even without a motor and wind. Make such homemade toy everyone can do it, it does not require special skills and tools. All you need is kebab skewers, paper clips, super glue and polyethylene. Such a mechanical bird is very light and strong, it is very interesting to play with it.

As you can see, everything is very simple and feasible! I wish you fruitful cooperation with your baby in creating a kite! Also, great launch! I hope you will tell us how your weekend in nature was and whether you managed to amuse your baby (and yourself too; I am still delighted with the flights of this wingless "beast"). I say goodbye until we meet again and remind you of the subscription for yourself and your friends!

3 20 175

The desire to take off and reach uncharted heights is inherent in each of us. And although, unlike birds, we cannot soar in the sky on our own, we are able to give the joy of watching free flight to ourselves and our children. Think we're talking about a plane ticket? And here it is not. We just want to tell you a few ways to make a kite. This simplest aircraft, made from improvised do-it-yourself tools, will give you a lot of positive impressions and emotions.

Did you know that the first kites plied the skies of ancient China in the second century BC? e.? Today the art of building and running them is back in vogue. And every year, every second Sunday in October, World Kite Day is celebrated.

By the way, the hero of our today's article is sometimes called "kite" in a foreign manner. So, when you come across this term, don't be surprised.
And now it's time to do snake building.

The easiest way

Do you want to spend a fine day with fun and profit, watching how a kite made by yourself soars cheerfully in the sky like a bird? if you don't have experience in creating such aeronautical structures, we advise you to start your journey by assembling the lightest kite model. It is attractive in that it can be done without a complex drawing.

For work, you will need the simplest materials at hand:

• tracing paper;
• scissors;
• wooden twigs or skewers about 60 cm long;
• adhesive tape or electrical tape;
• thick thread or twine.

Instead of wooden twigs, thin window glazing beads will do, and tracing paper can be replaced with plain paper (but remember that the lighter the kite, the better it will fly).

Fold the twigs crosswise as in the photo, fix the junction with a thread or a thin rope, lubricate it with quick-drying glue for strength.

Put the resulting blank on tracing paper and cut out a quadrilateral (well, you can’t call it a rhombus from the point of view of mathematics), for which the crossed sticks will be diagonals. Attach the twigs with adhesive tape to paper basis, Special attention take the corners.

Cut out a strip of tracing paper about 2 m long and 2 cm wide. Glue it around the perimeter of the quadrangle with adhesive tape.

Glue the intersection of the rods on both sides of the tracing paper with adhesive tape. With a nail heated on fire, carefully burn a through hole to fix the thread to the snake.

Pass the thread through the hole, make a loop and tie it around the cross. Remember that the loop must be with inside snake. Tie a thread, cord or fishing line wound on a spool to the loop (see how to make a spool at the end of the article).

The most important stage has come - decoration. Entrust this task to the child: he will independently decorate the craft at his own discretion. If you are collecting a test copy to study its flight characteristics, you can skip the design stage.

The simplest kite is ready. You can go outside to catch the wind and cheer yourself up.

Diamond shaped kite made of plastic bag

Want to make your kite more resistant to the elements. We suggest you use polyethylene as an improvised material. You will get it absolutely free of charge by cutting the old tight package. Another good option to give new life old things - take umbrella fabric. It is dense, light and does not get wet.

A little time, accuracy, strict adherence to the step-by-step photo instructions - and your kite will be ready to take off on its first flight. You will see that conquering the expanses of heaven is a fascinating pastime. Moreover, this version of the snake is more advanced than the first. He equipped with a bridle, making it easier to control.

original version

Who told you that a kite can only be triangular or diamond-shaped? Away with these outdated stereotypes. A little imagination and you can assemble a flying machine at home in the shape of a butterfly, flower or fish.

For work you will need:

• thick flexible wire;
• colored paper;
• marker or pencil;
• scissors;
• glue stick;
• thick thread and a piece of thin rope.

First of all, think over the scheme and size of your future creation. Draw a sketch on paper and think over the design.

And now it's time to bring ideas to life. Take pieces of flexible wire and bend them according to your scheme. Wrap the ends of the wire tightly with thread, for a secure fit, make at least a dozen turns on each connection and tie a knot.

Put the blank on paper, circle it with a marker, leaving a couple of centimeters around the perimeter for allowances. Make notches on the allowances so that the edges do not wrinkle when bent.

Spread the remaining allowances with glue and glue to the base of the workpiece. You can make a kite out of paper or fabric in several colors. In this case, cutting necessary elements, do the same.

To strengthen the frame, tie additional pieces of wire on the back of the structure.

You can decorate the product with tissue paper or shreds of thin fabric, you need to glue them to the front side.

It remains to fix the cherished thread of control. In order for the kite to fly, it must be done correctly. Regardless of its size and shape, fasten the rope in 3 places on the frame on the back of the product. Next, tie its ends, stepping back from the center of the structure by 30 cm, and tie the thread.

Your own fantasy kite is ready to fly. Any child will appreciate such a toy. But he will get even more joy from launching his new pet if adults find time to teach him this art.

Rectangular kite

We present to your attention a master class for creating a rectangular flying kite.

Make it with your children and you will get a triple benefit:

• give the younger generation the skills to work with your own hands;
• show that reality is much more interesting virtual world gadgets;
• get a lot of pleasure from joint creativity.

Yes, there is a triple! You can list the advantages of such a hand-made for a long time, but it's time to proceed directly to manufacturing.

* based on handmadecharlotte.com

For work you need:

• parchment paper, sheet 36*51 cm;
• wooden sticks or light slats, 2 x 60 cm, 48 cm and 36 cm;
• colored corrugated paper;
• strong thread;
• reel with fishing line;
• glue stick and PVA;
• a small metal ring;
• scissors.

Fold the parchment sheet lengthwise, lining up the edges. This is necessary to outline the line of the middle. Along the top edge of the narrow side of the rectangle, place the smallest stick, stepping back from the edge by a centimeter. Lubricate the free edge of the sheet with glue and wrap it so that the stick is inside, it should be tightly fixed.

Lubricate a stick 48 cm long with PVA and glue to the center line of the workpiece.

Lay the remaining sticks along the diagonals of the rectangle.

Glue them with pieces of paper, as shown in the photo.

Cut out squares or arbitrary figures from colored paper and stick on the front side of the rectangle.

On both sides of the intersection point of the diagonals, make a hole.

With pieces of thread, tie the ends of the sticks at the upper corners of the rectangle, pulling them together a little.

Tie a long piece of thread to the upper right corner of the kite. String a ring on the thread, it will help control the flying machine. Then thread the thread through the holes previously made in the center of the rectangle and pass it through the ring again. Tie the end of the thread to the upper left corner of the product.

Tie the end of the line tightly to the control ring.

Glue long strips of corrugated paper to the bottom of the kite. These "tails" will help him balance in the air currents. Their optimal size is 5 cm * 2.5 m.

The air wanderer is ready to surprise you with its flight characteristics. Good luck with your flight!

Cardboard coil for a kite at home

In order for the kite to proudly soar up, you need a very long thread or fishing line. Naturally, walking with an armful of thread in your hands is not advisable. For comfortable starting and control, a coil is used. You can buy ready-made, or you can make it from cardboard at home.

* Based on materials from eventor.ru

For work you will need:

• corrugated board;
• glue gun;
• scissors or cutter;
• pencil;
• ruler;
• compasses (preferred but not required)

Draw a circle with a diameter of 20 cm. Cut out two such blanks from cardboard. Cut comfortable finger slits on them, they should match exactly on both circles.

Cut several strips 2.5 cm wide.

Mark the inner circle, use a compass or a suitable template.

Fold the cut strips along the contour of the cutouts, glue with hot glue.

Glue the inner ring in the same way.

Glue the second circle on top of it.

Glue the end of a long thread to the inner surface of the spool and wind the thread.

So that it does not get confused, tie a match to its end, fix it with glue. Insert the thread into the slot on the outer ring.

With such a handy accessory, your flying kite will conquer not only the sky, but also the hearts of your children.

Now let's talk about how to fly a kite correctly. For spectacular flights, you need to achieve maximum controllability and maneuverability of the product.

1. Select open space to launch, otherwise, instead of enjoying the flight, you will have to take your kite out of the trees over and over again.
2. Make sure the wind is blowing outside. Without it, you will not be able to launch your creation. Optimal wind strength when thin tree branches sway and ripples flow through the water. If it is stronger, there is a risk of snake wreck. Then stand with your back to the wind and hold the kite in front of you. If it's built right, it can fly right out of your hands. Why not magic?
3. Having problems with flight control? Check if the thread is attached to the bridle exactly in the middle. Failure to comply with this condition will lead to uncontrollability of the kite.
4. The bridle is fixed correctly, but the snake lives own life, completely ignoring your commands? Checking the tail. Try it alternately lengthen and weight. Increase the length, if this does not help, tie a weighting agent to the tail. It can be a paper bow or just a bunch of grass - use what is at hand.
5. Is it hard for a kite to fly? Doesn't he want to gain height? Try lightening the tail. Get rid of excess decor or shorten it a little. But remember the golden rule: measure seven times, cut once.

Armed with our advice and detailed master classes you can get to work. A little practice - and a kite of any design, assembled with your own hands, will become commonplace for you. Do not be afraid to conquer heights and teach this to your children.