How to properly dismantle a pvc door. How to remove a plastic door from the hinges on the balcony: instructions

Very often, during the operation of PVC products, homeowners face the question of how to remove a plastic door from its hinges. During this procedure, it should be remembered that everything should be done carefully so as not to violate the integrity of the structure. Plastic doors can be found in any residential or public space, where they act as an entrance element. In some apartments and cottages, they serve as an integral part of the balcony block.

General characteristics of the door structure

The mechanism of plastic doors is quite simple. It includes a box and a canvas, reinforced with three or four loops. The panel is made of PVC and has a frame made of durable metal. Removal and re-installation is best done with an assistant.

Strong and durable hinges for plastic doors are complex, they are made of Teflon. It is very important to understand their internal structure in order to easily dismantle the structure later. The loop consists of the following elements:

• door insert;
• frame element with pins for fastening;
• movable and adjustable sleeve located between the frame and door parts.

The loops are equidistant from each other. This helps to evenly distribute the load. The upper and lower elements are installed along the line of the box. In order to mask the fittings, plastic caps are usually put on top of the hinges. In this case, the building looks solid.

Loop mechanisms can be:

• overhead (for balcony doors);
• applied (for pendulum);
• card: non-removable and removable;
• mortise: simple and bolted;
• invisible;
• screw-in (for light canvases weighing up to 25 kilograms).

The choice of hinges is determined by the type of construction and profiles of the frame with sashes, the presence of an amplifier, the thickness of its walls and how the sashes will open and close.

Reasons for dismantling

The need to remove the doors may appear for the following reasons:

• Breakage or displacement of fasteners.
• Replacing the door leaf or individual parts.
• Repair in the room.
• Opening enlargement.
• Moving large furniture.

It is important not only to carefully remove the canvas from the hinges, but also to subsequently install it in place.

Dismantling technology

Before removing the plastic balcony door, you first need to clarify the type of construction and pay attention to the details of the fittings. For dismantling, a simple tool is used:

• screwdriver straight and Phillips;
• a set of hexagons;
• pliers;
• wire cutters;
• finisher;
• mount.

The simple process of removing the door involves several steps:

All actions should not be rough and sharp, otherwise the hardware breakage is inevitable.

Before removing the doors, it is recommended to carefully cover the fittings from the plastic door with soft material or even carefully dismantle it.

Reverse installation

First, you should put the canvas in the opening so that loops can be put on top of it without any problems. You should focus on the bottom loop. The canvas must be kept straight to prevent possible distortions. Video on how to install a balcony door, see here:

Secondly, fit the end loop onto the support rod and adjust the position of other elements.

Thirdly, close the door without touching the handle and without fixing the lock.

Fourth, install the axle cylinders of each hinge in place and press on the lower pins. Its edge should go up to an audible click. The end of the rod should return to its original position and protrude from above by about fifty millimeters.

You can tighten the hinges with a hex wrench

Fifth, if necessary, twist the loops so that the canvas aligns.

Sixth, put on decorative caps and check the operation of the structure.

Before starting operation, it is useful to lubricate the hinge parts with oil or cover them with graphite shavings.

You can adjust the plastic door using a microlift and a limiter. The first fixture does a great job of troubleshooting regardless of the weight and size of the canvas. It prevents sagging of very heavy door panels. The microlift takes on part of the load, but only when it is closed. Usually it is presented in the form of a roller located at the bottom of the structure, or a movable plate at the top of the web.

The limiter helps to prevent sagging of the web, and also determines the maximum angle of its opening, protecting the panel from hitting the slopes.

How to fix sagging doors?

It is recommended to open the plastic sash and find a hexagon screw on the top hinge. Using a key, the screw is rotated 2-3 turns clockwise. Next, you need to check the overall performance.

How to eliminate side rubbing of the door leaf?

On the lower canopy on the inside of the door there is a side screw. By screwing it in a clockwise direction, you can restore the position of the door leaf. It will no longer be able to rub against the side beam of the frame and will close easily.

How to establish tightness?

At the ends of the door there are special eccentrics. By rotating them, the door mode is adjusted. Eccentrics must be deployed at equal angles. In this case, the sash will close tightly. You should also adjust the canopies with special screws.

How to adjust the door handle?

Move the decorative plate 90 degrees. Under it are hidden the mechanism of the handle and the mounting screws, which should be screwed tighter. For details on debugging plastic doors, see this video:

When removing the door from the hinges, the most important thing is not to damage the fittings, otherwise you will have to go to the store or suffer with a poorly opening door.

Plastic doors need to be removed for maintenance 2 times a year in order to lubricate and adjust the moving mechanisms. Many people are interested in how to remove a plastic door from its hinges.

The need to remove plastic interior doors from the hinges occurs infrequently. In many cases, minor repairs can be made without dismantling the structure.

It is necessary to remove the balcony door from the hinges in such situations:

1. fasteners are broken, require replacement - to adjust or replace any parts and accessories, you need to remove the door from the hinges;
2. the room is being renovated - it is necessary to remove the double-glazed window to protect it from pollution or damage;
3. if it blocks the passage - sometimes even in the open position, the PVC sheet prevents large objects and furniture from being carried through the door frame opening.

Rules for doing work

You need to remove the balcony plastic door if one of the hinges is broken, or the door leaf needs repair. You also need to remove the door to lubricate the fasteners with oil. You can replace faulty fasteners without any problems, since the design is of high quality and mobility. It is enough to lubricate the door mechanism once a year. This increases the durability of the product.

It is necessary to remove the PVC door leaf according to the rules. The entrance structure, unlike the balcony one, is equipped with reinforced fasteners and a mechanism that protects against burglary. It has a lot of weight, so in such cases it is better to work with an assistant. The metal-plastic product is equipped with 3 fasteners.

If you need to remove the metal-plastic front door, then you should proceed according to the following plan:

• It is necessary with the help of pliers and a screwdriver to disassemble all 3 boxes of hinged hinges. Remove the decorative caps by prying them off with a screwdriver.
• Press down the upper fastener and pull the hinge pin out of the groove by the lower end with pliers.
• The next step is to perform the same actions with the middle mount.
• Then you need to lift the sash up by 50 mm and tilt it in your direction. If the structure is heavy, then you can complete this step by slipping a lever under the sash.
• Rotate the structure so that the lever-rotation of the lower sash comes into action. Then carefully lift and remove the structure from the bottom fastener.

After removing the product, lubricate or change the fasteners, repair the door leaf. After the repair, the main task is to install the door leaf evenly so that it opens easily. It is necessary to adjust the position of the product after its installation.

The design of a plastic balcony door is not very different from ordinary interior doors. The door to the balcony includes a door frame and a leaf fixed on hinges. You can remove the balcony sash with your own hands. The product is small in size and light in weight, so you can do all the work without an assistant.

Most often, the installation of plastic balcony doors is carried out on only 2 hinges, which speeds up the work on their dismantling. You can also find sashes on 3 fasteners - then slightly different calculations and methods of dismantling will be needed.

Fasteners have a simple removable design, so the balcony sash must be slightly opened and raised by 2-3 cm using a mount as a lever.

To remove the balcony sash from the hinges:

1. Remove the protective caps from the mounts.
2. Open the sash, but do not block it.
3. Press on the pin of the upper mount in order to pull its end out of the groove.
4. Using pliers, pull the pin out of the groove, after grabbing it at the bottom of the loop.
5. Bend the sash towards you and pull the sash up by the handle to release the lower pin.
6. After that, the structure is freely removed.

When the product is removed, you can carry out repairs and lubricate the fasteners.

Reverse installation

When installing the door in place, all work is performed in the reverse order:

• First you need to install the canvas in the opening of the door frame, so that the hinges can be easily put on top of it. You need to adjust according to the location of the lower mount. The sash must be kept level so that there are no distortions in the future.
• Put the hinge on the support rod and adjust the location of other parts.

• Close the sash without holding the handle and without installing locks.
• Mount the upper and lower axle cylinders of the fasteners and press on the lower hinges. The end of the pin should lift up until it clicks. The end of the rod should return to its initial position and protrude no more than 50 mm from above.
• Fasteners are screwed with a 6-point wrench to align the door. Then you need to install it in place, put on decorative caps.

After all this, the functionality of the door structure is checked. Before using the structure, it is necessary to lubricate the hinges with oil.

Adjustment of the product is carried out with the help of a limiter and a microlift. These devices will help to eliminate problems and sagging of the canvas. When the sash is closed, the microlift takes over the load. This device is made in the form of a roller, which is located at the bottom or top of the movable plate web.

Proper care of loops

Hinges need proper care. Therefore, after removing the door leaf, it is necessary to process them.

Consider how to lubricate PVC door hinges:

1. Clean the structure of debris and dust. You can wash it with gasoline.
2. Wipe the mounting surface, remove all dirt.
3. Lubricate fasteners with special grease.

Lubricant can be bought in stores. It is sold in an oil can, with which it will be more convenient to process the fasteners with grease. Processing can also be performed if the canvas is in place.

A plastic door is an attractive design that has many positive features. That is why it can increasingly be found as an entrance, balcony and interior design in houses. It is also distinguished by practicality of use and low cost.

However, like any other, it needs quality care and timely repairs, and sometimes it needs to be removed from its hinges. This may be needed for various reasons - to disassemble, clean, decorate or check the operation.

Traditional fasteners

Attention! To understand the principle of removing the structure, you should understand what fasteners are on it. They may differ in their appearance and design. Accordingly, the principle of withdrawal is also somewhat different.

Peculiarities

They are distinguished by a rather complex design. It is important to understand the principle of the device, which will allow you to remove it without any problems. The device is represented by the following components:

1. Metal tab. This component is often called the door part.
2. A frame part that has built-in pins needed for fastening.
3. Remote bushing. It is located between the metal tab and the frame part.

Such components are able to ensure proper fit of the frame, while maintaining smooth opening and closing. If necessary, you can adjust the hinges in the required direction, ensuring a more correct functioning of the constipation or lock.

Possible product options for plastic structures that differ in their color

The adjustment can be done in two ways. One of them is horizontal. It is done using a stitch pattern. The second method of adjustment is vertical. It involves the use of adjusting screws, which are located under the decorative caps of the products.

Fasteners need lubrication from time to time. This will extend the service life, take care of reliability and durability. According to the type of fastening, they are divided into overhead and applied options. Among the most popular are overhead options. They are also considered the easiest to remove. It should be understood that initially you should pay special attention to overhead models. This will allow you to purchase a high-quality design that will be easy to remove and disassemble. To do this, you need to learn a little more about overlay models. They are used for mounting a balcony door.

The quality of the functionality of the doors themselves depends on the quality of the installed products. Very often distortions occur, in which the loops are primarily to blame, because due to the low level of production, they have extremely weak characteristics and simply cannot withstand the weight.

The modern hinge is classified according to GOST, they all differ in mounting options that affect the weight of the door leaf and the direction in which it opens. Various areas of application are possible. therefore, you need to pay attention to the characteristics that the manufacturer usually indicates when selling the product.

You should pay attention to a number of points, among which are the following:

1. The design of the sash and frame profile.
2. The presence or absence of an amplifier.
3. profile wall thickness.
4. The weight of the sashes and their dimensions.
5. opening principle.

All these points should be taken into account so that the structure serves for a long time and there is no need to remove the canvas. Most often, the hinges are quite strong and reliable, in view of the fact that they are made of Teflon. If suddenly the loop fails, there will be no difficulties with its replacement. For them, side cutters, pliers, a hammer, a doboynik are useful. Most often, the removal of the structure is necessary if low-quality fittings were originally installed, it is out of order, or the door is broken.

The principle of operation of a standard balcony design

When is demolition required?

Dismantling may be planned or the problem occurs suddenly. Very often it is a breakdown. A certain fastening, the door itself may fail, or its high-quality adjustment is required. In most cases, this will have to remove the structure from the hinges.

Another common cause is the replacement of individual parts or the installation of a new door. In these cases, unhinging becomes a necessity. Also among the reasons are repair work in the house, in which the canvas significantly interferes, or the process of expanding the opening.

Removing the metal-plastic sheet yourself

How is the job done right?

Disassembly involves the removal of the canvas. The algorithm of work should be followed in order to achieve a favorable outcome of the dismantling process. There are three main steps in the stripping process.

The first step is to remove the overlays from the canvas. To do this, open the loops, removing caps from them that perform a protective function. The principle boils down to the fact that the door is covered, leaving the handle raised up. After that, the overlay is gently pry with a screwdriver to bend the plastic.

Removing the main pin with pliers

The next step is the need for parsing. To loosen the mechanism, press the hinges at the top, helping to lower the pin down. You can completely remove the axis with pliers. The final step is the actual removal of the canvas. To do this, you need to grab it and tilt it towards you. Only after that it is gently lifted so that the loops are separated. It should be borne in mind that the design has an impressive weight, so you may have to work together.

After that, there is a need for subsequent installation of the structure in place. To do this, the canvas is inserted into the opening, putting it on the hinges, while focusing on the bottom. It is put on the support pin and the position of the elements is adjusted. After that, the door is finally inserted into the opening, the axial cylinders are mounted, twisted and the decor elements are put in their place. In conclusion, the functioning of the canvas and fittings should be checked. If there are defects, the operation of the door leaf should be adjusted.

Various types of plastic doors

Attention! At first glance, it may seem that the withdrawal process is unusually simple. However, it is not recommended to deviate from the instructions. It has been designed by experienced professionals who know how to proceed in order not to damage the components and can be reinstalled normally.

Now you know how to do it yourself. This job does not require any special skills. Removal is a simple and accessible process for every person, and calling specialists is not required. The canvas itself will be removed extremely simply and without problems, especially if its installation was performed correctly. If necessary, you can always pay attention to the video, which illustrates this process in detail. This will get rid of even possible difficulties and will guarantee the ease of the process itself.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your own ...

New Articles

New comments

S.A.

Grade

Svetlana

Grade

Sergey

Grade

Sergey

Grade

Alexei

Grade

Latest reviews

adminadmin

It would seem that it is difficult to dismantle a PVC balcony sheet? In practice, it turns out that without instructions on how to remove a plastic balcony door from its hinges, it is not easy to do the work yourself, especially for people without experience.

A seemingly simple design is quite heavy, so it will require a competent algorithm of actions during the dismantling process. To remove it from the hinges neatly, quickly and without the risk of damage, you need to know exactly which hinges you will have to work with.

Hinge options for PVC doors - components

The design of a balcony door, as well as a double-glazed window, is based on the use of fasteners - hinges. The main material for the manufacture of loops is Teflon. Teflon products cope with the load, despite the impressive weight of the door leaf, guarantee smooth operation of the structure, and contribute to the creation of a tight connection with the door frame.

Each loop consists of several important elements:

• metal part No. 1 (mounted to the door);
• metal part No. 2 (mounted on the frame due to built-in pins);
• remote sleeve (redistributes the load from the door to the box).

The dismantling process has its own nuances, but the main rule is accurate coordinated movements without haste according to the instructions.

How to dismantle the canvas of a plastic balcony door with your own hands: a guide

There is nothing difficult in removing the plastic balcony door by studying the video on the thematic channel. Step-by-step instructions will provide additional assistance. Following the recommendations, you can solve the dismantling problem without having special skills, which will save on paying for the services of specialists.

How to remove a PVC balcony door with your own hands:

1. The door must be closed without closing the handle to the end.
2. On each side of the structure, it is necessary to remove the caps that mask the hinge mechanisms with a screwdriver.
3. Start dismantling from the top loop. To do this, click on the upper part - the pin protruding beyond the loop.
4. Using pliers, the cylinder is picked up at the bottom of the loop, after which it is delicately removed through the bottom of the mechanism.
5. The door is tilted towards itself, easily pulled by the handle, taking into account the weight of the structure, preventing a fall.
6. The canvas is lifted a few centimeters up, releasing the cylinder in the lower support of the mechanism. The design is ready for complete dismantling, since the hinges no longer fix it.

In the same way, you can install the product in place.

PVC door installation - reverse order

After the completion of repair and correction work, the plastic door must also be delicately installed in place. This will require:

1. Insert the canvas into the opening so that it is on the hinges in the upper part, avoiding distortions.
2. The lower loop is also put on the support pin with the adjustment of all elements.
3. The axial cylinders of the hinges are mounted in place, after which the pins are manipulated in the reverse order of dismantling with pressure from the bottom up until a characteristic click and protrude outward by half a centimeter.
4. You can adjust the position of the door by twisting the hinges.

At the final stage, the decorative masking mechanisms of the loops - caps - are returned to their place.

What to do with rusted hinges?

Prolonged use of the door can lead to the formation of rust on the hinge mechanisms. In such cases, it is important to remove the canvas from the hinges without sudden movements.

Do not use a hammer or other tools to try to break the rust layer on the fasteners. Such manipulations will only exacerbate the situation.

The solution will be a special aerosol that can remove plaque within 6-12 hours after application. As soon as the mechanisms are cleaned, they begin to work with them according to the instructions for dismantling.

When can you do without dismantling?

Problems with the functioning of the PVC door leaf do not always need to be solved by dismantling. Some problems are fixed on the spot with simple tools - a hex key and a screwdriver.

To understand that the protective caps on the hinge mechanisms are not a source of problems, you need to start the repair by removing them (use a screwdriver). Often it is these details that negatively affect the operation of the door. A simple treatment of the caps with lubricant can solve the problem of squeaking, tight closing and opening.

In case of skew, it is necessary to correct the position of the web directly in the holes of the loops hidden under the caps, using a key and a screwdriver.

As a preventive measure, the structure needs to be lubricated from time to time, to adjust the position, preventing problems from aggravating when dismantling the balcony door becomes the only way to solve it.

Any balcony door over time needs adjustment, which experts recommend annually, and minor repairs in some cases. It is not necessary to attract specialists to carry out these works, adjustment and simple repair of a balcony door with the knowledge of simple technology is easy to do on your own, while saving financial resources.

Fig.1 Construction of plastic door leaves

Repair work of doors on the loggia or balcony, which can be done on your own

Breakage of the internal parts of the fittings, requiring the removal of the sash and subsequent disassembly of the door leaf, significant mechanical damage to the plastic frame of balcony doors, deformation and decomposition of plastic due to temperature and chemical exposure are not subject to self-repair. If the hinges in the frame or door leaf are torn out, the welds will break and diverge, and complex repairs are also required.

In most cases, it is necessary to replace the fittings and the door leaf, which can be quickly installed by a specialist who understands the repair. With your own hands, you can perform the following simple operations to repair PVC doors:

• adjustment of the web in the horizontal and vertical plane, clamping force to the frame;
• replacement of broken locks and handles, their adjustment in case of weakening;
• inserting a new sealant into the leaf and frame;
• replacement of glass bags;
• cosmetic repair of scratches and minor damage to the door leaf.

Rice. 2 Some damage to the balcony PVC profile

Plastic door leaf adjustment

The standard design of plastic balcony doors has adjusting elements in the form of bolt heads with hexagonal recesses, the main tool for turning them is an L-shaped hex wrench with a diameter of 4 mm. Adjustment work includes the following operations:

Rice. 4 Setting the distance and web pressure, checking the seal

Replacing handles and locks

Usually, a balcony lock is built into the handle, if it breaks or does not work well, it is removed and the lock mechanism is lubricated, if this does not help, the fittings are completely changed. They do the same with mortise or overhead locks that can break - they are changed if the lubricant did not help.

If the door handle is broken, its replacement consists of several operations:

1. Pull the decorative PVC trim over and turn it 90 degrees.
2. Unscrew the mounting bolts and remove the window handle.
3. They put a new mechanism and fasten it with new or old bolts, close the handle with an overlay.

Rice. 5 Handle replacement

Removing the balcony door

When carrying out some repairs, the question arises of how to remove the fiberglass balcony door. It is quite simple, the operation is carried out in the following order:

Rice. 6 How to remove a plastic door leaf: workflow

1. Before removing the PVC balcony door, we remove the protective plastic pads from the hinges, slightly pulling them towards ourselves, if necessary, they can be slightly bent with a flat screwdriver.
2. Depending on the design, the balcony door is removed from the hinges by moving the released pin in the upper hinge down or up, pressing on the free end with a finger or a hard object, with a tight move you can pull it out with pliers.
3. Now you can remove the door, for which we open it slightly and lift it up, removing it from the bottom hinge until the sash is released.

The reverse installation is carried out in the following sequence:

1. The door leaf is put on the bottom hole on the axis fixed in the box (it is more convenient if the axis is slightly deviated from the vertical position).
2. Bring the upper loop to its part with a hole and holding the canvas, insert the cylindrical pulley into place.
3. They put on plastic lining and close the door leaf.

Installing a new seal

The sealing tape on the balcony door is changed if cracks, hardening, breaks appear on it. To change, you should select a seal that matches this profile, you need to install the tape on the door leaf and frame (you will need to remove the plastic balcony door), while taking into account that these are different seals with a different cross-sectional shape.

Better sealing is provided by chamber types, unlike petal ones, their cross-sectional area is larger, and they should be preferred when buying.

To replace the tape, you must perform the work in this order:

We prepare two different sealing tapes for the canvas and the box.

1. We remove the balcony plastic door from the hinges. To do this, remove the plastic lining and pull out the metal pulley, then slightly open the door and move upwards to remove the canvas from the bottom hinge.
2. We lay the canvas on its side, turn the fastening of the upper hinge to the side and remove the old tape, its connection is located in the middle of the top of the door leaf - from there, dismantling should begin.
3. We insert a new tape from the middle of the upper part, avoiding strong tension in the corners, glue the ends of the tape together and to the frame with rubber glue.
4. We return the upper hinge to its place and proceed to replace the seal on the door frame. We remove the old tape, clean the perimeter of dirt and dust and install a new seal, gluing it at the top in the middle.

Rice. 7 Installing the seal in fiberglass door leaves

When carrying out work, you should be careful not to confuse the mounting side of the sealing tape - usually it is located with a wide part of the profile on the outside of the canvas and the box.

Replacement of damaged double-glazed window

A broken double-glazed window can be repaired with your own hands by replacing the broken glass and sticking a sheet of the same size in its place. This work takes a lot of time and does not bring significant financial savings, therefore, in case of damage, it is easier to replace it with a new one.

It is easy to do the work yourself if you order a new double-glazed window according to the size of the old one - for an accurate measurement, it is enough to remove the top and side glazing beads and measure the width and height of the damaged package with a tape measure.

Rice. 8 Replacement of a double-glazed window for plastic balcony doors

The installation of new glazing is carried out in the following sequence:

1. Holding the glass window, remove the top and side glazing beads, prying them with a narrow spatula or a wide flat screwdriver.
2. We take out the old package from the frame, clean the opening from dirt and dust and install new glass.
3. We return the glazing beads to their place with a slight pressure.

When carrying out work, it is important not to confuse the fasteners (it is better to mark the glazing beads), otherwise small gaps may appear in the corners due to deviations in size.

There are several ways to resolve the issue of how to repair a plastic coating:

• Clay Cosmofen. It is a liquid plastic of low viscosity of cloudy transparency, it is used for gluing rigid plastic structures, it dries within 4 seconds, the total setting time is 16 hours. To remove scratches, white Kosmofen is used, which is applied to the damaged surface, after hardening it is removed with a sharp chisel and then polished.
• Specialized putties for plastics. When deciding how to fix severe damage, you should focus on automotive putties. These materials are widely used for repairing plastic, they can close large holes in plastic, and after grinding and painting, get a fairly flat surface.
• Use of a hair dryer. To remove small scratches, you can use a regular hair dryer - when exposed to heat, the edges of the scratches melt and they become less noticeable.

Rice. 9 Plastic repair

On your own, you can make adjustments and simple repairs to the doors on the balcony (remove and insert a double-glazed window, replace the seal or handle) - you need an ordinary household tool and minimal construction skills to work. To eliminate significant damage or noticeable scratches on the plastic, it is more practical to use the services of specialists who can change the door or professionally hide the damage.